Buy or Renew
Buy or Renew
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
1124
Views
0
Helpful
4
Replies

3502i will not join 5508

wjguest28
Level 1
Level 1

‎09-26-2012 10:25 AM - edited ‎07-03-2021 10:43 PM

I have a 3502i(AP_1) that will not join a 5508 WLC(WLC_1)(code 7.2.103). The 3502i(AP_1) will join 4402 WLC(WLC_2)(Code 7.0.230). I have another 3502i(AP_2) that will join the WLC_1 & WLC_2. I am using capwap discover through DNS and hard coding the primiary WLC to AP_1 & AP_2. When I debug capwap events and errors, I see the static capwap messages and replies. Both of the WLC are on the same subnet. I have defauted the AP_1 and it joins the CISCO-CAPWAP-CONTROLLER as expected. When I change the Primiary WLC to WLC_1 it goes back to the CISCO-CAPWAP-CONTROLLER. If i change the primiary WLC to WLC_2 it joins. If I change the primiary back to WLC_1 it joins WLC_2 even though it is not a secondary. I know the previous joined WLC are stored in NVRAM, so that might be why it is doing that. I can join other ap to WLC_1 just not this one.

*spamApTask3: Sep 26 17:17:15.214: <<<<  Start of CAPWAP Packet  >>>>

*spamApTask3: Sep 26 17:17:15.214: CAPWAP Control mesg Recd from 10.22.110.3, Port 9360

*spamApTask3: Sep 26 17:17:15.214:              HLEN 4,   Radio ID 0,    WBID 1

*spamApTask3: Sep 26 17:17:15.214:              Msg Type   :   CAPWAP_PRIMARY_DISCOVERY_REQUEST

*spamApTask3: Sep 26 17:17:15.214:              Msg Length : 94

*spamApTask0: Sep 26 17:17:15.214: b4:14:89:83:d0:00 Received LWAPP PRIMARY_DISCOVERY_REQ from AP

*spamApTask3: Sep 26 17:17:15.214:              Msg SeqNum : 0

*spamApTask3: Sep 26 17:17:15.214:  

*spamApTask3: Sep 26 17:17:15.214:       Type : CAPWAP_MSGELE_DISCOVERY_TYPE, Length 1

*spamApTask0: Sep 26 17:17:15.214: 00:14:f1:48:c0:00 Discarding Primary discovery request in LWAPP from AP supporting CAPWAP

*spamApTask3: Sep 26 17:17:15.214:              Discovery Type : CAPWAP_DISCOVERY_TYPE_STATIC_CONFIG

*spamApTask3: Sep 26 17:17:15.214:  

*spamApTask3: Sep 26 17:17:15.214:       Type : CAPWAP_MSGELE_WTP_DESCRIPTOR, Length 40

*spamApTask3: Sep 26 17:17:15.214:              Maximum Radios Supported  : 2

*spamApTask3: Sep 26 17:17:15.214:              Radios in Use             : 2

*spamApTask3: Sep 26 17:17:15.214:              Encryption Capabilities   : 0x00 0x01

*spamApTask3: Sep 26 17:17:15.214:  

*spamApTask3: Sep 26 17:17:15.214:       Type : CAPWAP_MSGELE_WTP_FRAME_TUNNEL, Length 1

*spamApTask3: Sep 26 17:17:15.214:              WTP Frame Tunnel Mode : NATIVE_FRAME_TUNNEL_MODE

*spamApTask3: Sep 26 17:17:15.214:  

*spamApTask3: Sep 26 17:17:15.214:       Type : CAPWAP_MSGELE_WTP_MAC_TYPE, Length 1

*spamApTask3: Sep 26 17:17:15.214:              WTP Mac Type  : SPLIT_MAC

*spamApTask3: Sep 26 17:17:15.214:  

*spamApTask3: Sep 26 17:17:15.214:       Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 10

*spamApTask3: Sep 26 17:17:15.214:              Vendor Identifier  : 0x00409600

*spamApTask3: Sep 26 17:17:15.215:

        IE            :   UNKNOWN IE 207

*spamApTask3: Sep 26 17:17:15.215:      IE Length     :   4

*spamApTask3: Sep 26 17:17:15.215:      Decode routine not available, Printing Hex Dump

*spamApTask3: Sep 26 17:17:15.215: 00000000: 01 00 00 04                                       ....

*spamApTask3: Sep 26 17:17:15.215:  

*spamApTask3: Sep 26 17:17:15.215:       Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 17

*spamApTask3: Sep 26 17:17:15.215:              Vendor Identifier  : 0x00409600

*spamApTask3: Sep 26 17:17:15.215:

        IE            :   RAD_NAME_PAYLOAD

*spamApTask3: Sep 26 17:17:15.215:      IE Length     :   11

*spamApTask3: Sep 26 17:17:15.215:      Rad  Name     :  

*spamApTask3: Sep 26 17:17:15.215: AP_1

*spamApTask3: Sep 26 17:17:15.215: <<<<  End of CAPWAP Packet  >>>>

*spamApTask3: Sep 26 17:17:15.215: b4:14:89:83:d0:00 Primary Discovery Request from 10.22.110.3:9360

*spamApTask3: Sep 26 17:17:15.215: b4:14:89:83:d0:00 Join Priority Processing status = 0, Incoming Ap's Priority 4, MaxLrads = 50, joined Aps =0

*spamApTask3: Sep 26 17:17:15.215: b4:14:89:83:d0:00 Primary Discovery Response sent to  10.22.110.3:9360

Labels:
0 Helpful
4 Replies 4

wjguest28
Level 1
Level 1

‎09-26-2012 11:50 AM

More info:

------------------ show capwap client rcb ------------------

AdminState                  :  ADMIN_ENABLED

SwVer                       :  7.0.230.0

NumFilledSlots              :  2

Name                        :  AP_1

Location                    :  somewhere

MwarName                    :  WLC_2

MwarApMgrIp                 :  10.20.240.211

MwarHwVer                   :  0.0.0.0

ApMode                      :  Local

ApSubMode                   :  Not Configured

OperationState              :  UP

CAPWAP Path MTU             :  1485

LinkAuditing                :  disabled

AP Rogue Detection Mode     :  Enabled

AP Tcp Mss Adjust           :  Disabled

Band Direct                 :  Enabled

Predownload Status          :  None

Auto Immune Status          :  Disabled

------------------ show capwap client config ------------------

configMagicMark         0xF1E2D3C4

chkSumV2                39682

chkSumV1                3003

swVer                   7.0.230.0

adminState              ADMIN_ENABLED(1)

name                    AP_1

location                Somewhere

group name              No-WLANS

mwarName                WLC_1

mwarIPAddress           10.20.240.212

mwarName               

mwarIPAddress           0.0.0.0

mwarName               

mwarIPAddress           0.0.0.0

ssh status              Enabled

Telnet status           Enabled

numOfSlots              2

spamRebootOnAssert      1

spamStatTimer           180

randSeed                0x0

transport               SPAM_TRANSPORT_L3(2)

transportCfg            SPAM_TRANSPORT_DEFAULT(0)

initialisation          SPAM_PRODUCTION_DISCOVERY(1)

ApMode                  Local

ApSubMode               Not Configured

AP Rogue Detection Mode Enabled

OfficeExtend AP         [0] Disabled

OfficeExtend AP JoinMode[0] Standard

Discovery Timer         10 secs

Heart Beat Timer        30 secs

Led State Enabled       1

Primed Interval         0

AP ILP Pre-Standard Switch Support Disabled

AP Power Injector Disabled

Infrastructure MFP validation Enabled

Configured Switch 1 Addr 10.20.240.210

non-occupancy channels:

Ethernet (Duplex/Speed) auto/auto

AP_1# ping WLC_1

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 10.20.240.212, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms

0 Helpful

Stephen Rodriguez
Cisco Employee
Cisco Employee
In response to wjguest28

‎09-26-2012 11:55 AM

can you grab a screen shot of the Security > AP Policies?

Also a debug mac addr < ap mac> debug capwap events enable , debug capwap errors enable

HTH,
Steve

------------------------------------------------------------------------------------------------
Please remember to rate useful posts, and mark questions as answered

HTH,
Steve

------------------------------------------------------------------------------------------------
Please remember to rate useful posts, and mark questions as answered
0 Helpful

wjguest28
Level 1
Level 1
In response to Stephen Rodriguez

‎09-26-2012 12:08 PM

AP Policies are the same on the 4400 WLC_2

Preview file
16 KB
0 Helpful

wjguest28
Level 1
Level 1
In response to Stephen Rodriguez

‎09-26-2012 12:16 PM

I ran enabled the debugs you requested and there are no events. It is like the AP stops trying to contact WLC_1 and goes stright to WLC_2. If I default the AP then the debug events that are displayed above are what is shown. Attached is AP_1 boot from console.

135734-ap_1.boot.log.zip
0 Helpful
Customers Also Viewed These Support Documents
Review Cisco Networking for a $25 gift card