06-30-2016 07:09 AM - edited 07-05-2021 05:20 AM
8.2MR2 (8.2.121.0) is now posted, the beta process is closed. Thanks for all the feedback!
CSCva43051 |
Substantial degradation of unicast video performance past 15 clients |
CSCva48770 |
2800/3880: Any DCA event during radio reset is causing cmd-timeout |
CSCva26525 |
8.3 8510 ATF crash task-iappSocketTask iappProcessAtfClientStats+245 |
CSCva51528 |
AP BEACON config value is always shown disabled in WLC after AP reboot |
CSCva55049 |
2800/3880: Limit 'best' DCA to 80 MHz instead of 160 MHz |
CSCuz71914 |
Issues in XOR radio[Monitor Mode] when AP mode moved to Sniffer |
CSCuw18522 |
APF-3-WLAN_OUT_OF_RANGE errors filling up msglog on WLC |
CSCux55307 |
AIR-CT5520 crash in dtlArpTask |
CSCuy75993 |
SNMP returns 11ac module present for 11ac aps like 3700/IW3700 |
CSCuz29885 |
Flex AP automatically switching to non DCA channels |
CSCuz49482 |
FlexConnect: WLAN config stays in ap-specific on moving from |
CSCva06192 |
Kernel panic: PC is at select_task_rq_fair+0x70/0x65c |
CSCva17231 |
on HA failure, Active WLC RF group stuck on 'HA Standby' & RRM stopped |
CSCva25810 |
Flex AVC profile is not removed from the 3802 AP |
CSCva34774 |
WLC crash at apfReceiveTaskwith reason System Crash |
CSCva41168 |
After few hours operation,Client will get wrong IPv6 subnetwork |
CSCva47003 |
8.2MR2: Kernel Panic on 2800/3880 AP PC is at do_bad_area+0x34/0x88 |
CSCva47557 |
Profile:Wrong Group ID reported by 2800/3880 APs cause RF Group failures |
CSCva49188 |
8.2MR2: AAA Vlan override failing on Barabdos AP 8.2.111.30 |
CSCva05514 |
3802 AP - cannot allocate 2880 bytes buffer for pool #16 in NSS mode |
CSCuz48289 |
FT-PSK PMF-Optional, EAPoL M2 MIC error on change to local auth-flex |
CSCva40348 |
AP2800: Radio crashed with bad_vector_pc points to halspd_data |
CSCuz72620 |
ATF:Clear Atf command doesnt clear AP override to disabled. |
CSCuz40509 |
ATF: config all command needs to have override column |
CSCuz20714 |
WLC crashes on emWeb with Reaper Reset |
CSCva30541 |
8.2 MR2: 3800 XOR radio not reporting noise when in monitor role |
CSCva25878 |
3800 AP not clearing evenlogs on WLC |
CSCva29450 |
DHCP option 60 shows shared_printenv error |
CSCva23304 |
Kernel Panic: PC is at wlRecv+0x150/0x964 |
CSCva23178 |
Antenna gain for 1810W APs not returned correct |
CSCuz58657 |
3800 AP: client not joining with link-encryption enabled |
CSCva22748 |
3800: Failing to change channel in sniffer mode |
CSCva32819 |
AP 3800/2800 crash due to Kernel panic |
CSCuz56372 |
SANITY:ME-3800 crashes with kernel panic |
CSCva06132 |
ME: 1852 SW crashed on process ctrl_rx_task |
CSCva06192 |
Kernel panic: PC is at select_task_rq_fair+0x70/0x65c |
CSCva23345 |
3802 AP Radio FW sensord off-channel stuck |
CSCux63449 |
WLC 8.0.120.0 Crash on TransferMsgPeerSend |
CSCuz54125 |
5500 SSHpmCert Memory Corruption( overrun) on Pmalloc/Pfree buffers |
CSCva18981 |
WLC Crash 8.2.100 |
CSCva32509 |
Layer 3 client roam fails on controller running 8.0.134.26 |
CSCva32819 |
AP 3800/2800 crash due to Kernel panic - OOM |
CSCva37881 |
mDNS AP 2800 and 3800 does not forward mDNS packets not on native VLAN |
CSCva38926 |
XOR no noise/interference/rogues/neighbors in Flexconnect mode |
CSCva32183 |
Issue in clean air when moved from monitor to client serving |
CSCva39041 |
3800: RRM wrongly trying to set AP1142 to UNII-2 extended channels |
CSCva37393 |
3800: Beacon Stuck - off channel stuck |
CSCva30755 |
3800: Sensord dying after radio reset |
8.2.111.23
CSCuz88260 |
Unable to handle kernel NULL ptr dereference at virtual addr 00000004 |
CSCva21709 |
1800 AP crashed - apsw_watchdog about to reboot with reason: capwapd |
CSCva25338 |
2800/3800/1800 'show ap summary' displays wrong ip for static ip config |
CSCuy67885 |
5520 or 8540 may have no Manufacturing Installed Certificates |
CSCuz81177 |
2800/3800 Cmd timeout, RX Hang seen |
CSCva07520 |
2800/3800 DP ERR>22>mv_dp_msg_check_rx:1747>FW Failure Status for opcode:7... |
CSCux82102 |
AP 3600+11ac module crash on memory corruption for 8.2 |
CSCva14511 |
2800/3800/1800 DHCP_OPTION_43 messages not seen on AP console |
CSCva13591 |
3802 AP fails to join the WLC after capwap restart |
CSCva19392 |
2800/3800/1800 ERROR:receiveWlanMsg(): mgmt subtype:0xf len:1423 - dropped event |
CSCva20303 |
5520 Mem Leak %APF-3-LIST_ERR: avc_api.c No entry available in table |
CSCuy33972 |
WLC ssh host-key generate command not having an effect |
CSCuz52725 |
2800/3800- Macbook is sometimes using 2SS rate on uplink |
CSCva05657 |
3802 AP - cmd_to off channel stuck Tx FSM is not Idle & TCQ Verify zero |
CSCva12610 |
2800/3800 -Clients are deauthenticating with EAPOL bcast interval expiry |
CSCuz62398 |
1800 capwap local bcast discovery stops working on upgrade to 8.2.102.125 |
CSCva16181 |
2800/3800 Sniffer Mode set on XOR Band fails |
CSCva21076 |
2800/3800/1800 Rx hang detection resulting in multiple radio resets & reboot |
CSCug98522 |
PMIPv6: MAG delivering multiple DNS servers to clients |
CSCuq05475 |
Controller GUI shows AP's NAT IP instead of private |
CSCut42406 |
Ct5508 crashed while disabling Mobility oracle. |
CSCuu91943 |
8510 WLC crash while accessing the controller crash file info thro GUI |
CSCuw28141 |
Reaper Reset: Task "SNMPTask" missed software watchdog |
CSCuw30129 |
Debugging logging quickly falls behind real-time |
CSCuw36069 |
Threshold MIBs incorrectly set for WSSI modules. |
CSCuw65706 |
AP1530 WGB Drops Tx used w/ other 1530 WGB in same MAC address range |
CSCuw89229 |
Mesh instability with fast-convergence when RF link is unstable |
CSCux22620 |
8510 WLC crash in radiusTransportThread system task |
CSCux28775 |
WLC per-WLAN client traffic stats accuracy enhancements |
CSCux29207 |
Issue with SNMP GetBulk request - cLAPGroupsHyperlocationEnable |
CSCux32328 |
Token Bucket leak with QoS Roles and with WebAuth on 8.0.120.2 |
CSCux37498 |
CoA with wlc 8.1.131.0 shows error message on ISE server |
CSCux41577 |
WLC and AP out of SYNC for Client Exclusion List |
CSCux45077 |
AP3500 crashed due to "LWAPP CLIENT" process. |
CSCux47470 |
8.0.110.14 controller crash at openssl_cert_hash_algo_check_callback |
CSCux51484 |
Memory leak observerd in EOGRE SNMP task |
CSCux60012 |
With New Mobility - Mobility Members Don't survive reload |
CSCux60873 |
Radius interface overwrite does not work when chosing "ap group" intf |
CSCux65158 |
ATF : Globally configured mode not applied to newly joined APs |
CSCux66190 |
No.of Interim Update Sent field is not flushing |
CSCux69928 |
Wism2 Silent crash PMALLOC_DOUBLE_FREE on 8.0.122.18 MR3 |
CSCux74970 |
MAG w/PMIPv6 does not assign secondary DNS to clients via DHCP |
CSCux75330 |
Mismatch AP count and unable to add more APs to WLC |
CSCux78464 |
WLC crashes in Process Bonjour_Process_Task |
CSCux81598 |
Memory Allocation problem with SAP1602 |
CSCux83260 |
BGL-Alpha: "lbs-ssc" &" sha256-lbs-ssc" missing in WLC web UI |
CSCux83635 |
FATAL: Couldnt Send message out prints on 5500/7500 standby console |
CSCux91996 |
Rogue containment not starting if no client info on best RSSI AP |
CSCux92251 |
AIR-CAP2702 with WLC 8.2 doesnt allow HTTPS client access |
CSCux93468 |
Anomalous Fan Speed/Temp reading for 8540 |
CSCux95607 |
ATF : User allowed to configure ATF on 1600 unsupported platform |
CSCuy13829 |
AIR-CAP2602I crash on dot11_pmkid_timeout |
CSCuy14547 |
HA Config Sync failed |
CSCuy18768 |
Halo module doesn't work with RxSOP after image upgrade/dowgrade |
CSCuy19485 |
Client detail table view miss alignment for a single client in bar graph |
CSCuy21224 |
upport of 3G/4G module on 3600E/3700E APs |
CSCuy23295 |
intf nasid given priority over wlan nasid in default Ap group |
CSCuy33247 |
AP send disassociation frames twice and Optimized roaming go wrong |
CSCuy37694 |
WLC crash running 8.0.120.0 at task apfRogueTask_1 |
CSCuy43365 |
5520 / 8540 8.2.100.0 Crash in Reaper Reset: Task "apfReceiveTask" |
CSCuy45485 |
Containment to choose AP based on rogue client detected as well as RSSI |
CSCuy45955 |
DFS scan causes beacon transmission to be stuck on AP |
CSCuy47407 |
Client leak at anchor controller |
CSCuy51343 |
Telnet/ssh config for AP is not retaining after upload/download config |
CSCuy52607 |
Data Plane crash - cvmcs_StaToDS |
CSCuy63742 |
Acct commands send inconsistently to TACACS server for rapid commands |
CSCuy73622 |
Time sync failure for mmMsg_HandoffComplete on MC not printed on debugs |
CSCuy92423 |
CWA broken in beta image 8.0.122.50 |
CSCuy94534 |
3700/2700 on DFS dont see 3700/2700 as neighbor when Rxsop High/Med/Low |
CSCuy95327 |
802.1x frames are not marked with DSCP CS4 |
CSCuz01093 |
Traceback apf_site_override.c:2888 Invalid value 0 for WLAN |
CSCuz02871 |
Webauth acl is not pushed from flexgroup when a new wlan is added to AP |
CSCuz15763 |
Flex Data DTLS enabled AP gets stranded with WAN link flap |
CSCuz22237 |
mobility express CORSICA: client not authenticated from 802.1x,wep) |
CSCuz22985 |
BCAST Queue full causing Clients to stay Multicast-direct Pending status |
CSCuz23758 |
Local Profiling Not Sorting Correctly, not corrected on 8.0.132 |
CSCuz24467 |
Mem corruption on GUI crash related to hreap avc group page |
CSCuz38059 |
Anchor WLC does not free Client Sessions - client entries stale |
CSCuz39100 |
ATF config not applied when no AP joined on controller |
CSCuz46264 |
Flood of %SOCKET_TASK-7-DATA_PROCESSING_FAILED error messages |
CSCuz47863 |
SHA256 self-signed cert for WLC web admin |
CSCuz49616 |
WLAN-VLAN Mapping incorrect when AP moves across AP-Groups of diff WLANs |
CSCuz52435 |
Evaluation of wlc for OpenSSL May 2016 |
CSCuz56009 |
Client reassoc not happening when central dhcp enabled |
CSCuz56598 |
Enabling radio after disable/enable admin status,ifno channels available |
CSCuz57198 |
SNMP AP3800:Clean air on xor radio is not functioning properly |
CSCuz57392 |
AP3800 SNMP: Need errors for Channel Settings |
CSCuz58908 |
AP3800 FRA configurations not retained in HA setup |
CSCuz60033 |
WLC is dropping data packets in Hybrid VoWiFi setup |
CSCuz63274 |
mDNS snooping drops IPv6 mDNS traffic |
CSCuz67766 |
WLC crash due to software watchdog for apfMsConnTask_0 |
CSCuz68446 |
NOS: bsnAPIfTable has NULL entries |
CSCuz69239 |
Flex local auth: 11n clients showing as 11ac |
CSCuz70444 |
AP3800: XOR Microcell stuck on max power |
CSCuz70999 |
AP3800: WLC crash while executing XOR radio commands |
CSCuz71197 |
8500 wlc crash when starting 11v dms on sim clients |
CSCuz72522 |
AP3800: FRA COF Metrics shows stale value for disabled Radios |
CSCuz73422 |
1852 AP EAP-TLS client authentication fails |
CSCuz73502 |
Spartan:2.4G data not shown for AP-Ch.Util,AP-Dist by SS,AP-Model Distr |
CSCuz74209 |
AP3800: client network preference default is not default |
CSCuz74637 |
WLC login banner does not show up on GUI. When using CLI it works fine. |
CSCuz74989 |
AP3800: Issue setting channel for XOR radio in sniffer mode |
CSCuz77060 |
SNMP:Radio Mode Trap generated when admin status changed for xor |
CSCuz79051 |
WiSM2 8.1.131.0 crash in ewaFormServe_multicast_detail |
CSCuz79869 |
8510 silent crash |
CSCuz81176 |
AP3800: Beacons stuck seen in radio 0 & 1 |
CSCuz81415 |
1msec delay in processing IGMP packets causing Bcast queue to remain ful |
CSCuz84096 |
RRM doesn't change channel for mesh APs in 8.1 and 8.2 |
CSCuz86679 |
5508 HA SSO crash on SNMPTask |
CSCuz87680 |
WLC crashes with task:emweb on changing wlan config |
CSCuz89491 |
BVI interface is down with latest recovery image |
CSCuz89662 |
1852 Reject clients association due to "suppRates statusCode is 18" |
CSCuz96571 |
Ap-list new mobility packets flooding between AirOS WLC |
CSCuz97117 |
AP3800 CCO image "show inventory" displays incorrect SN & VID format |
CSCva03344 |
Client capabilities shown as 160 MHZ even client is not 160MHZ |
CSCva03888 |
3802 : DSCP marked as 0 in capwap header with CAC config |
CSCva08910 |
Unable to view the client details by clicking on connection rate |
CSCva09603 |
AP3800: 160 Mhz throws SNMP error |
CSCva11172 |
No netflow records exported for anchored client in Auto Anchor Scenario |
CSCva12198 |
SNMP get on device for table cld11nMcsTable returns only 24 indices |
CSCva12984 |
DHCP_OPTION_43 functionality broken in AP3800 AP |
CSCuz81074 |
ME3800: Upgrade failure from 8.2 mr1 to 8.3 |
06-30-2016 04:11 PM
Hope CSCux23003 will be addressed in this code.
06-30-2016 04:32 PM
Hope CSCux23003 will be addressed in this code.
I think it is, Rasika. BST is showing Known Fixed Release as 8.2.113.3.
07-01-2016 01:28 AM
hi
yes, I can confirm CSCux23003 has been addressed on this beta release
regards
07-01-2016 01:22 PM
Thanks Javier
07-01-2016 02:00 PM
Will we see bug CSCuz32677 resolved in these releases, throughput problems?
07-02-2016 10:51 PM
hi Ben
The fix is not yet ready, but we are working to see if it can be included (it only affects specific applications and flow types)
regards
07-08-2016 06:50 AM
Hi All
I'm having my "yearly" maintenance window in 3 weeks. I have planned to upgrade from 8.0.120.0 to 8.2.111.0, because I plan to get some 2802i in a few months.
Would you, in my situation, recommend me to directly go to this beta version (which has a very long list of fixed issues, also for the new AP series) or stick to the stable 8.2.111.0?
I could also do an upgrade at a later time, but by far better would be my normal maintenance window.
It's two 5508 controllers in a failover configuration.
07-11-2016 12:26 AM
Hi
if you plan to do 2800/3800, I would suggest to use current or next beta refresh to be published in the coming days. There are significant improvements for 8.2 branch that would be of great benefit vs using 111/110.0
Beta code has limited support (TAC would only support MR beta until CCO final code is published). if you need extended support due to significant business reasons, please reach out to me to discuss possible solutions.
Our release target is for end of July, so we may be in time
regards
07-11-2016 06:58 AM
Thanks for your reply.
In case of a technical issue with the current beta release, I can make a special maintenance window :)
07-26-2016 10:37 AM
Installed today build 8.2.111.40. Upgraded from build 8.0.120.0. The upgrade took around 40 minutes for my SSO 5508 pair with 50 connected APs. I pre-downloaded the image to the APs which is not included in these 40 minutes.
All in all it took around 1 hour for the full upgrade. So far, after 10 minutes of testing, everything seems to be working. I use local mode APs of the models 3702i and 2702i.
07-12-2016 11:42 AM
Sounds good - do you know if ME images will be available as well?
- and is this the right place to ask about inclusion of bugfixes in beta images, specifically CSCuz29774, I've had an 1852 disconnecting from the master AP 4-8 times a day since I started testing them, and I suspect CSCuz29774 to be the culprit.
Regards,
N.C.
07-13-2016 06:04 AM
hi
>Sounds good - do you know if ME images will be available as well?
I just posted ME image, it is available on the download folder
> - and is this the right place to ask about inclusion of bugfixes in beta images, specifically CSCuz29774,
You can direct bug questions directly to me
At this time, CSCuz29774 is not scheduled to be included in 8.2, but will be part of 8.3
regards
07-18-2016 06:19 PM
Would CSCuz84305 impact the creation of heatmaps in Prime? i have a building that has nothing but 2802i WAPs, and while there is a heatmap generated/displayed for 5Ghz, there is no heatmap for the XOR radio (currently running in 2.4). In my office I have a 3800, and while the surrounding 3702's have heatmaps in 2.4 and 5, there is no heatmap for the 3800 XOR radio (running in 2.4.)
On the use of beta code for customers with 2800/3800 WAPs. Should I use/deploy the 8.2.110.10 as originaly suggested, or is it best to deploy the 8.2.11.30? I have a residential hall that is WiFi only and will be using the 3800's, so they have to work.
BTW - running 5508 on 8.2.110.0 and Prime is 3.1 MR1 (support for XOR radio).
07-19-2016 05:08 PM
Although the list of bugs fixed in 8.2MR2 is pretty long the list of bugs fixed in 8.0MR3 and forthcoming on 8.0MR4 is even longer.
That raises of course question which of the bugs fixed in 8.0MR3/4 are also present in 8.2MR2 and are might not yet addressed? Is there some kind of "bug parity" list available? Would the release notes of 8.2MR2 still list those non addressed but present bugs as "known/open issues"?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide