11-16-2015 11:25 PM - edited 07-05-2021 04:14 AM
I am using the autonomous AP AIR-CAP2702I-S-K9 (Firmware: ap3g2-k9w7-xx.153-3.JBB5). I want to set up a Guest SSID with web authentication.
First, I had created the vlan, Guest SSID with open authentication which work properly as vlan guest group IP address.
When I click on the web authentication box, it assigned the guest group IP address directly and no any log in page pop up. As this time, it can't connect to internet under this IP.
May I know more detail about this setting?
11-24-2015 05:55 AM
HI
Check this Configuration guide which may be help you
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wlan-security/116897-configure-technology-00.html
11-24-2015 10:02 PM
I had followed this setting step. However, it still can't work. No any log in page pop up and assigned the guest group IP address directly.
03-02-2016 01:46 AM
I had followed this setting step. However, it still can't work. No any log in page pop up. It direct to www.msn.com only. Could you help me to review the setting??
config detail:
version 15.2 no service pad service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname ap ! ! logging rate-limit console 9 ! aaa new-model ! ! aaa authentication login default local aaa authorization exec default local ! ! ! ! ! aaa session-id common clock timezone +0800 8 0 no ip cef ip admission name web_auth proxy http ip admission name webauth proxy http ip name-server 8.8.8.8 ! ! ! ! dot11 syslog ! dot11 ssid Guest web-auth authentication open guest-mode mbssid guest-mode ! ! dot11 guest username Guest lifetime 60 password 7 115C415546425A ! ! ! username admin privilege 15 password 7 08154B1B59382C890 ! ! bridge irb ! ! ! interface Dot11Radio0 no ip address ! ssid Guest ! antenna gain 0 stbc station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 spanning-disabled bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding ip admission webauth ! interface Dot11Radio1 no ip address shutdown antenna gain 0 peakdetect no dfs band block channel dfs station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 spanning-disabled bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding ! interface GigabitEthernet0 no ip address duplex auto speed auto bridge-group 1 bridge-group 1 spanning-disabled no bridge-group 1 source-learning ! interface GigabitEthernet1 no ip address duplex auto speed auto bridge-group 1 bridge-group 1 spanning-disabled no bridge-group 1 source-learning ! interface BVI1 ip address dhcp client-id GigabitEthernet0 ipv6 address dhcp ipv6 address autoconfig ipv6 enable ! ip forward-protocol nd ip http server ip http authentication aaa no ip http secure-server ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag ! ! ! radius-server local nas 10.130.123.120 key 7 1511021F0725 ! ! bridge 1 route ip ! ! ! line con 0 line vty 0 4 transport input all ! sntp server 118.143.17.82 sntp broadcast client end
03-02-2016 03:44 AM
Hi,
Please follow this:
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wlan-security/116897-configure-technology-00.html
Regards
Don't forget to rate helpful posts
03-16-2016 04:09 AM
We want to test our DUT's throughput on 2.4G HT40 mode with Cisco2702 AP,
Could you know any images for supporting 2.4G HT40 on Cisco2702 AP? (AIR-CAP2702E-T-K9)
Thanks a lot.
04-14-2016 11:29 PM
I still can't solve this problem as this instruction. Do you have any other suggestion?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide