01-31-2019 12:41 PM - edited 07-05-2021 09:47 AM
Hello,
i have an CAP 2602 with IOS Version ap3g2-k9w7-xx.153-3.JF9
I have access to the GUI but i can not activate the Radios.
When I try it at Easy Setup -> Network Setup - i got a failure.
See---
Thats the default:
Building configuration... Current configuration : 1536 bytes ! ! Last configuration change at 17:54:37 UTC Sun Sep 1 2013 version 15.3 no service pad service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname ap ! ! logging rate-limit console 9 enable secret 5 $1$k5t3$YaHDVR4gdkoQia.8KG2on0 ! no aaa new-model no ip source-route no ip cef ! ! ! ! dot11 pause-time 100 dot11 syslog ! ! no ipv6 cef ! ! username Cisco password 7 02250D480809 ! ! bridge irb ! ! ! interface Dot11Radio0 no ip address shutdown station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 spanning-disabled bridge-group 1 block-unknown-source no bridge-group 1 source-learning --More-- no bridge-group 1 unicast-flooding ! ap#sh run Building configuration... Current configuration : 1536 bytes ! ! Last configuration change at 17:54:37 UTC Sun Sep 1 2013 version 15.3 no service pad service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname ap ! ! logging rate-limit console 9 enable secret 5 $1$k5t3$YaHDVR4gdkoQia.8KG2on0 ! no aaa new-model no ip source-route no ip cef ! ! ! ! dot11 pause-time 100 dot11 syslog ! ! no ipv6 cef ! ! username Cisco password 7 02250D480809 ! ! bridge irb ! ! ! interface Dot11Radio0 no ip address shutdown station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 spanning-disabled bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding ! interface Dot11Radio1 no ip address shutdown station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 spanning-disabled bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding ! interface GigabitEthernet0 no ip address duplex auto speed auto bridge-group 1 bridge-group 1 spanning-disabled no bridge-group 1 source-learning ! interface BVI1 mac-address c067.af88.88a1 ip address dhcp client-id GigabitEthernet0 ipv6 address dhcp ipv6 address autoconfig ipv6 enable ! ip forward-protocol nd ip http server no ip http secure-server ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag ! ! bridge 1 route ip ! ! ! line con 0 line vty 0 4 login local length 0 transport input all ! end
Via CLI it doesn´t work too.
Some ideas?
01-31-2019 12:58 PM
Hay
hope everthing is ok
try to configure the Ap via cli
this is a clear guide on how to also note that you should no shut "interface Dot11Radio0"
02-01-2019 01:43 AM
02-02-2019 12:03 PM
Hey,
i tried already via CLI and again with your manual, but i can not see any ssid.
I don´t think i have an UX, because the name of my AP is AIR-CAP2602I-E-K9
Could it be a problem with my power injector?
I don´t use one from Cisco, but one with a lot of power!
02-02-2019 12:25 PM
hello friend
this ap doesnt need poe plus
so a normal power injector should work but it should give at lease 15.4W
try to shut no shut the >> Int dot11radio0
also if ur ssh put terminal monitor so u can view the logs as they show up
also attach the show logging
also attach the current config of the ap
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide