11-27-2020 09:21 AM - edited 07-05-2021 12:50 PM
*spamApTask2: Nov 27 18:14:50.099: 00:5f:86:1e:66:e0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 100, joined Aps =0
*spamApTask2: Nov 27 18:14:50.099: 00:5f:86:1e:66:e0 Primary Discovery Response sent to 10.40.94.199:15203
*spamApTask6: Nov 27 18:14:50.249: c4:0a:cb:5c:7a:90 Primary Discovery Request from 10.40.94.114:48716
*spamApTask6: Nov 27 18:14:50.249: c4:0a:cb:5c:7a:90 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 100, joined Aps =0
*spamApTask6: Nov 27 18:14:50.250: c4:0a:cb:5c:7a:90 Primary Discovery Response sent to 10.40.94.114:48716
*spamApTask6: Nov 27 18:14:50.250: c4:0a:cb:5c:7a:90 Primary Discovery Request from 10.40.94.114:48716
*spamApTask6: Nov 27 18:14:50.250: c4:0a:cb:5c:7a:90 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 100, joined Aps =0
*spamApTask6: Nov 27 18:14:50.250: c4:0a:cb:5c:7a:90 Primary Discovery Response sent to 10.40.94.114:48716
*spamApTask4: Nov 27 18:14:50.251: c4:0a:cb:2d:c3:d0 Primary Discovery Request from 10.40.94.59:1321
Do you have any suggestions?
many thanks
Regards Antonio
Solved! Go to Solution.
11-27-2020 05:10 PM
config ap lifetime-check mic enable
try this
11-28-2020 01:40 AM
Cisco Controller) config> ap lifetime-check mic enable
Incorrect usage. Use the '?' or <TAB> key to list commands.
(Cisco Controller) config>
not working
11-27-2020 05:33 PM
any update it seem work ?
11-27-2020 02:51 PM - edited 11-27-2020 04:34 PM
do this command on WLC and see result.
config ap cert-expiry-ignore mic enable
or
config ap lifetime-check mic enable
11-30-2020 06:11 AM
Not sure why nobody seems to have mentioned it, but for anyone else reading this, the full info is in the field notice which addresses this problem - read through it slowly and carefully - twice for good measure. It answers all the questions:
https://www.cisco.com/c/en/us/support/docs/field-notices/639/fn63942.html
To fix it you must do the right things in the right order - time, software, config - and don't miss that it can affect both AP and WLC certs.
Some products which were too far out of support can't be fixed - only changing the time back to the past will keep them working.
06-13-2021 04:37 PM
Hello, I experienced this problem too but it was with some 1142 hw v1-v2-v3-v4 and 1242 hw v1-v2. I solved this by adding these commands to accept mic self-certificates, but too old due to hardware revision. Typed on CLI from the WLC, no reboot requiered.
config ap cert-expiry-ignore mic enable
config ap cert-expiry-ignore ssc enable
save config
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: