08-09-2016 11:01 PM - edited 07-05-2021 05:35 AM
Dear Team,
I have couple of Cisco AP1800 at my branch office I want them to be register with WLC -5520 located at my HQ, Please help me with the steps I have to take to complete this installation.
Below are more details
AP Model
AP1800 "AIR-AP1852E-E-K9"
Cisco Aironet 1800 Series (IEEE 802.11ac) Access Point
Primary Software Version : 8.2.110.0
Controller 5520
Software Version | 8.2.110.0 |
Solved! Go to Solution.
08-10-2016 03:20 AM
Yes.
To convert from Mobility Express to CAPWAP, in enable mode enter the command "ap-type capwap".
08-10-2016 03:51 AM
Mea culpa. I didn't notice the AP was a 2702.
Go to HERE. Download the CAPWAP image (TAR file) and then un-pack the IOS into the AP using the command "archive download-sw /over tftp://<TFTP IP address>/filename.tar".
08-09-2016 11:29 PM
Post the complete output to the WLC command of "sh sysinfo".
08-09-2016 11:53 PM
Please find attached as requested, Appreciate your urgent support.
08-10-2016 12:14 AM
Firmware looks good. Regulatory Domain looks good.
Console into the AP and reboot the AP. Post the entire boot-up process.
08-10-2016 12:22 AM
Dear Leo,
I have WLC at my HQ and I have 2 Access Points at Branch, how I can register them to my WLC which is located at HQ from Branch?
08-10-2016 01:31 AM
I have WLC at my HQ and I have 2 Access Points at Branch, how I can register them to my WLC which is located at HQ from Branch?
If the AP boots in CAPWAP image then the AP will be able to find the WLC if DHCP Option 43 is enabled.
08-10-2016 02:32 AM
Currently the AP is using Autonomous Image do I need to change it to lightweight image to register the same?
08-10-2016 02:40 AM
Currently the AP is using Autonomous Image do I need to change it to lightweight image to register the same?
1850 do NOT support autonomous IOS. Only CAPWAP or Mobility Express.
To convert from Mobility Express to CAPWAP, in enable mode enter the command "ap-type capwap".
08-10-2016 02:54 AM
I am sorry the AP type is AIR-CAP2702I-E-K9 with software image(AP3G2-K9W7-M), Version 15.3(3)JBB6, RELEASE SOFTWARE (fc2).
can I change this one to lightweight and add the same to WLC ?
08-10-2016 03:20 AM
Yes.
To convert from Mobility Express to CAPWAP, in enable mode enter the command "ap-type capwap".
08-10-2016 03:41 AM
This command is not working
08-10-2016 03:51 AM
Mea culpa. I didn't notice the AP was a 2702.
Go to HERE. Download the CAPWAP image (TAR file) and then un-pack the IOS into the AP using the command "archive download-sw /over tftp://<TFTP IP address>/filename.tar".
08-10-2016 04:40 AM
I have WLC 5520 with Version as 8.2.110.0 and AP model as AIR-CAP2702I-E-K9, what is the appropriate lightweight version I have to download for AP?
08-10-2016 03:11 PM
It doesn't matter, Irshad. The main objective of the CAPWAP image is to get the AP to find and join a controller. Once the AP joins the controller, the controller will evaluate the version of the full IOS found in the AP. If the AP doesn't have a full version or if the full version is not at the same level as the controller, the controller will PUSH the correct version down to the AP.
08-10-2016 11:09 PM
Thanks.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide