Hi, I have Two Cisco WLC 3500 installed at 2 different DC. I need to configure Redundancy between the two WLC. Since the WLC are installed at 2 different DC the management IP of the two wlc are in different subnet. Whats is best possible Redundancy...
Forum Posts
Hi, I need to upgrade an MSE 3355 running version 8.0.130 to CMX 10.2. I can't seem to find any documentation for the upgrade procedure, has anyone done this upgrade before? Cisco software to download for the MSE 3355 is the CISCO_CMX-10.2.0-213-3355...
Resolved! 2702I Not reaching N Speeds.
We have several 2702i's that are managed by our 5508 WLC, several users are complaining about slow speeds in general. We tested a couple of AP's in 2.4 and 5ghz only and both cap at around 18-20 mbps up and down. We even forced N connections only but...
I have use ISE 2.4 do BYOD with vWLC 8.2.100.0 version and I have use NSP_Onboard Authorization profile, Clients it doesn't get an ip address, So I have try create new Authorization profile in other name but it does the same then I have try to remove...
Device: - AIR-AP2802E-B-K9 - Software Version 8.6.101.0 Receive the following message when attempting to change 2.4Ghz radio channel: Error in setting radio mode to manual. Getting this error message when - changing band from 'Automatic' to 2.4GHz...
Hi We have wlc5508 and ap3600. When pc is connected to internet through guest ssid, we always cannot connect to its server to get the speed. Anyone can explain it? Thank you
We recently upgraded from ISE 1.2 to ISE 1.4 and we have a custom portal that is not acting correctly. You get the initial redirect and you enter you credentials and then select submit. It automatically redirects you back to the portal. If you enter ...
Hello,We usually use APs 1702 which have IOS.The newer APs like 1830,1850 I think they do not have IOS anymore, so the config is different.Am I correct?And since in several months the 1702 is going to EoL, which "new" APs do we have whit the classicI...
HI I've been asked to look why we keep getting these, from what I've read, When a client is associated to the AP but stops communicating because of card removal, roaming out of range, etc. to the AP, the AP will wait until the idle timeout. Once t...
Resolved! ACS - Secondary linking errors
I am trying to repair a broken ACS Secondary configuration. I currently have 2 primaries and want to make one of them a secondary. These devices (virtuals) are both on the same version (5.8.1.4) and the same build. They also have unique licenses. ...
Dear Cisco community member. I have configured the AIR-RM1252G-E-K9 access point (IOS 12.4(10b)JDA3) Even thought the Interfaces are up I still do not see any service on the wireless media (no SSID or any kind of service on the 2.4 Ghz) Any he...
Resolved! Controller based AP not working
Greetings, One of the registered AP in my network stopped working, when i connected to console i found this messages. Kindly help me out. Cisco IOS Software, C2600 Software (AP3G2-RCVK9W8-M), Version 15.2(4)JA1, RELEASE SOFTWARE (fc2)Technical ...
Resolved! Display wireless users in PI 3.4 maps
Hello, I read about that PI can display users, rogues APs and users, microwave and bluetoosh in PI 3.4 maps, but could not find this option... Only displayed APs. Maybe anyone encountered this issue? Thanks.
Hi, We are using 3504 controller with 1832I AP. we are created IPSec VPN in our router to connect remote Site.We are able to ping from WLC to remote site VPN but unable to ping using wifi access point. I have checked my firewall and there is nothing ...
hi Everyone I got contacted for an interview as Network Consulting Engineer for services providers, although my resume is all about enterprise solutions (routing and switching). I won't say no to the interview, but I'm a bit lost, does such role focu...
