Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Recently the Cisco Prime infra was upgraded to 3.1. After which end client seeing Temperature status as "Both CPU temperatures are high" Under System Information in Prime Dashboard. Tried restarting the services, but still the issue is there. Can a...
Dear All, I have Cisco Wireless LAN 2504 having software version 8.0.115.0. I need to know the below points. Is this software is compatible with 3800 AP series. If not then will my existing 2504 be upgraded to latest software to support 3800 AP seri...
Hi Guys we have converted capwap to autonomous with ios 15.3(3)JF and then configured it in very simple way to broadcast SSID and associate clients , we tested it and it worked fine. But after rebooting the AP some how the AP was not able to show in ...
Hi All, I have access points in 2 sites that are joining a regional primary controller and each ap is a member of a certain ap group we configured a secondary controller to those APs that is located in another physical location "not in HA pair" ...
Hi guys, I tried to install certificate in my CMX, it is a success but when I check the the CMX portal, it is still uses the default certificate? I followed the CMX documentation about this maybe you can share what is happening here. Thanks
I recently attempted to upgrade our WLC environment (5508 and 15+ 2602 APs) and hit a few issues and was wondering if anyone else has encountered anything similar? My starting point was 7.3.112.0 on our WLC with a planned upgrade path of: 7.3.112...
We are upgrading our WLC 2504 from version 8.1.102.0 to 8.5.131.0. Need to know if this version will be compatible with ISE 2.1, the release note says 2.2 and 2.3 but did not mention about 2.1. Can someone confirm on this?
I have a appliance Prime Infrastucture with version 2.2 but comming soon the appliance it will be reemplaced with virtual machine wiht a new version 3.4. I thing download a backup since the version 2.2 and upload the backup on the virtual machine. ...
Resolved! WLC 2504: Web Auth certificate expires
Hey all! I'm using a wlc 2504. There is a third party signed (public signed) certificate for the guest portal. Can someone tell me how to recreate that certifcate? The current certificate is going to expire in a few days. Thank you!
Hi Guys, I have Access Points 1552 in Mesh Network, 5 GHz for the Mesh Backhaul and serving clients on 2.4 GHz I am wondering why I am not getting any Cleanair nor in the GUI nor in CLI show {802.11a | 802.11b} clean air device ap Cisco_AP any th...
Can some help me that mobile client disconnecting from WLC they should re login, I downgraded IOS from 8.5 - 8.3 from but still same problem. I am coping the log.
Resolved! flexconnect configuration: two options
for flexconnect its possible two ways for configuration: 1) without "vlan support" and, port where access point is connected, in access mode with this configuration obviously there are less settings and time for config 2) access point is in flexc...
Hi All,We have upgraded our controllers to version 7.6.100. After upgrading, the access points also upgraded their version to 15.2(4)JB3. But, the problem is that after this process the APs do not get IP. It stays on this state:*Sep 26 03:55:36.334: ...
Greetings! Is there an posibility to connect external third-party 3G modem via USB to ISR 891 router? I try to connect MTS 3G-CDMA450 modem (produced in Ukraine)
Hello, my access points are all at TX Power on Global. I can see that many only stand on TX Power Level 5. However, this is not enough to expose the WLAN far enough. If I manually set the access points to Power Level 1 or 2, my wireless network is ...
