Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hello,I have a Wifi access point (model cisco AIR-AP1832I-E-K9). In France, time changes every last Sunday of March 3:00 (plus one hour) and every last Sunday of October 2:00 (minus one hour).Can you tell me how to configure this in command line for ...
Resolved! Mobility Express stuck in DST
Greetings, European Summer Time ended last Sunday (October 28), but our ME controller doesn't seem to have noticed and is now one hour ahead. The time zone is configured correctly (GMT+1 Amsterdam, Berlin, Rome, Vienna) and NTP is in sync. I can't fi...
Hi experts, I am facing this issue with 3702 Access point, where randomly sends BPDU to the switchport and err-disables the port. obviously i have bpdugaurd enable on the port and i would like to keep it this way. the image that i am using on the AP...
Hi everyone,i have met a issue that is AP2802 cannot join WLC.AP model:AIR-AP2802I-H-K9software:8.3.143.0WLC release:8.3.143.0 AP get the ip address by DHCP. the log as below:ethernet_port wired0, ip 10.1.1.30, netmask 255.255.255.0, gw 10.1.1.254, m...
Resolved! Latency spikes every ~1 minute
Hi Meraki Community,I'm using 5 MR33s running firmware 25.13. We have had issues with Twilio VoIP and in our investigations have found our wifi network has latency spikes almost exactly every minute apart - it seems very mechanical in nature. Does an...
In this case, I use image mobility express and later use lwap when did upgrade with both ios always output this message and I was opening a case with the tac. and told me this problem with the hardware. Best regards.
Hi. We have a 2700 autonomous AP configured to allow domain users to authenticate access to the Wireless Lan. To connect to the wireless the users enter their username/password or tick the "Use windows credentials" box which prepopulates the fields...
Our Vulnerability Scanner says that the cisco AIR-AP2802I-E-K9 is a High Risk.The Reason for that is that the process Lighttpd is unsecure. Lighttpd is from a another vendor. When you follow this link you can see that the vendor already fixed this pr...
Good day i have a problem which is rather weird. i configured web auth (internal) using lobby account to create passwords for guests. however when i test only phones pass the auth stage and have access to internet. difference now is i have tested 2 l...
Resolved! SSID availability - Scheduling
Hello Forks !!!Hope you all are doing great :-P.My question is related to " SSID availability scheduling", so when I scheduled it to be not available does it disabled it or hides it ??Currently I have two SSIDs one for the guests and other for the em...
I need to take WLC backup using Cisco Prime
Hi! We have wifi network based on wlc5508 and 2702i ap everything works well except max client speed. Only 2 mbps of download/upload is availaible for each client, and there is no any qos/limits configured on controller neither uplink router. We have...
Dear All, Here is my issue, Firstly, i plugged the AP 2702i to the switch port model 3560G using RG-45 cable. When i logged into the Ap through the Web Browser, i saw this message as mentioned in the subject title.At the same time, i touched the AP f...
Resolved! Cisco 2504 controller not booting
SYS and ALM LEDs on steady amber when powered. Please what could be the problem with the controller?Controller does not load any startup config.How do I make the controller boot?
Hello folks, I'm wondering let's say I have a switch that I can access remotely only. The switch is IP address is configure below: switch1# ! int vlan 6 ip address 192.168.6.5 255.255.255.0 ! !int vlan 120 ip address 192.168.120.5 255.255.255.0 ! i...
