Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hi..Is it possible to configure local EAP Authentication using EAP-fast when active directory server is not both CA server & AD server. Although CA server is antoher standlone server in network. Pls help.
Hi Expert,I'd like to know how many Wireless AP Model can WCS supported for design, I mean I want to design Wireless for building and I am using WCS but I didn't find 1602 model from Cisco, I want to know if there is some files I have to updated. I a...
Hi all, I installed new MSE and integrated it with cisco prime I need to know if it is neccessary to add the CAS license first to can track the clients or can track without it for trial time ?
Hi,Can any give a brief explanation of the interference by channel graph (I attach the file)?In the lask week a problem of disconnections with client has came up, I'm not sure of the reason but I have checked logs an there is some lines about interfe...
Helllo,I tried to connect to the service port on a wlc model 8500 without success. I followed the wlc installation guide, putted an IP address/netmask on the port, connected the port to my laptop network card using a cross-over cable, and set up my c...
We're looking at updating our wireless network and was recommended a Cisco 2504 Wireless LAN controller. I have some questions I was unable to find out in the specs. Was hoping someone here had used one or knew the answers. Anywa we have or will have...
Flex connect AP AD user's disconnected after some time. I check the link it's fine. Please help me what is issue???I am using WLC 2504 version 7.2.x.x.
What is the best WLC code for point to point and point to multipoint bridging on a 2504 with 2602 APs? 7.2-7.4 had transparent vlan issues and I'm not sure if they were fixed in 7.5-7.6. We have 5-6 vlans that we are needing to bridge between a large...
Dear ALL, Can 5760 WLC controller with 1000 APs be used without new 3850 switch, I mean as a standalone WLC or it need to be only with 3850 switch thank you
Under what circumstances will a controller lower the power level on a 5 Ghz radio? In some areas I am seeing RRM controlled power levels as low as 5. I thought because of the greater number of available channels, the potential for co-channel interfe...
I took over a client that has several Cisco 1240AG AP's. Currently they are running the 2.4-GHz 802.11g mode but I see from the dashboard it has a 5-GHz 802.11a thats just disabled. I'd like to use the 5Ghz as well. I found the below on the specs for...
Hello,do I need any upgrade license to migrade from PI 1.3 to PI 1.4 or only a smartnet support is enough? Is there a documentation for the upgrade procedure from PI 1.3 to PI 1.4, I was unable to find it. Thank you. Marek
Hi,where can I learn more about Cisco Wireless? I have GNS3 and Cisco Pakettracer butthere is no simulation for wireless. Can someone tell me what I have to do to learn moreabout Cisco Wireless.Are there maybe some good books to learn from how to con...
Hello.. I am running a Cisco ACS Radius server. I have just setup wireless controller and AP is added successfully. Also able to connected on wireless network. I want to wireless users to authenticate throrugh certificate authentication. Is it poss...
Hi,I am having Cisco Controller 2504, when i am register remote AP's (3521) on controller, AP is register, but in AP settings and WLAN setting H-REAP mode is not showing.Please help on this.Regards,Jitesh.
