Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

Hello,I have a 350 client pcmcia card with the latest ACU, NDIS, Firmware the is associating between two AP's. One is a 1200 (12.02) with the better signal and the other is a 350 (12.02) weaker signal. The client is not associating with the stonger s...

tlchant by • Level 1
  • 620 Views
  • 1 replies
  • 0 Helpful votes

hello , I have purchased 2 aironet 1220 , (upgraded to IOS ) AP's & a few 350 PCMCIA cards , I was hoping to set up WPA , sadly the although the AP is WPA ready the APU for the 350 PCMCIA cards do not support it yet.I want to make the wireless networ...

Can I use the radius server that comes with Windows2000 server in the Internet Authentication Service with the Aironet 1200 for authentication? Or do I need to use Secure Access Server or something like it?

jmackin by • Community Member
  • 661 Views
  • 1 replies
  • 0 Helpful votes

. On Cisco Aironet Wireless Bridges – can we limit the CPE to Wireless Bridge Connection in Bandwidth? E.g. 128kbps, (instead of the 802.11x 1,2,5.5,11Mbps data rates). If not, then how can we achieve bandwidth control, since we wish to optimize the ...

alok_sharma by • Community Member
  • 782 Views
  • 1 replies
  • 0 Helpful votes

Dear all The 802.11 standard does not require that the Access Point broadcast the Service Set ID. This phrase is right or wrong I see the document which said we can set ,can you tell me answerthanks a lot

admin_2 by • Level 7
  • 521 Views
  • 1 replies
  • 0 Helpful votes

I am using the Cisco 350 card in an office environment, but my signal level is "very low" or "low" now at all times. I use a Dell CPiA laptop that, until a few days ago, always registered a "very good" or "excellent" signal strength.The laptop is abo...

jtalens by • Community Member
  • 1200 Views
  • 5 replies
  • 0 Helpful votes

I have worked with home wlan devices (dhcp/router/switch ie. SMC/Netgear/Linksys,etc.)), but am now venturing out to small businesses.I have a small rural medical clinic that is pursuing an online med package and needs wireless access to their existi...

wpcc by • Community Member
  • 649 Views
  • 1 replies
  • 0 Helpful votes

We are setting up a conference room with three access points(1200's). All three are set up using different channels(1,6 or 11). When we were doing some testing with 25 computers we noticed that whichever access point was directed to channel 11, that ...

rx33328 by • Community Member
  • 901 Views
  • 3 replies
  • 0 Helpful votes

Hi I have just had shipped 2x aironet 1220B series AP's .I just went to upgrade there software using AP1200-Cisco-IOS-Upgrade-Image-v1.imgusing the web browse to image option , all apeared to go well, but now when the AP reboots it sits with all 3 gr...

I was told it´s possible to configure a trunk beetween 2 parallel BR350 links working on different channels which are connected to a switch on both sides.My question now is if it´s possible to configure the same when one link is a 3rd party transpare...

t.franke by • Community Member
  • 570 Views
  • 1 replies
  • 0 Helpful votes

I'm having some trouble here, maybe it's lack of understanding or maybe I'm just a tool and am doing something dumb.Am I wrong in assuming that if I setup VLANs on an AP350 and map a simple WEP secured SSID to each VLAN, each of those SSIDs will beco...

jason by • Community Member
  • 704 Views
  • 1 replies
  • 0 Helpful votes

I am using a windows 2000 machine, when I install my wireless card I recieive an DHCP I/P Address,now my question WHen I go back to my desk and plug into my network connection without rebooting I get another I/P DHCP address which is normal. The prob...

jp0801 by • Level 1
  • 513 Views
  • 1 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card