cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
855
Views
0
Helpful
8
Replies

C9130AXI-B unable to get IP address from DHCP Server

ybp2000
Level 1
Level 1

Hello All,

I cannot get C9130AXI-B Access Point to get IP addresses from DHCP Server.

Configuration

DHCP Server (dhcpserver.de) is on Win 11, connected to Cisco Catalyst C1200-8FP-2G PoE switch

C9130AXI-B running EWC image v17.12.03 connected to the same switch

Management Interface of C9130AXI-B setup with a fixed IP (tried DHCP also)

When AP is powered up, it cannot get the network configuration (stuck in  flashing red-green-off LED). 

The following messages are in DHCP Server log:

 

 

 

[05/09/2024 14:45:04] Adapter 0 has recognized an incoming DHCP request
[05/09/2024 14:45:04] Adapter 0 has recognized an incoming DHCP request
[05/09/2024 14:45:04] DHCP message = DHCPDISCOVER
[05/09/2024 14:45:04] DHCP message = DHCPDISCOVER
[05/09/2024 14:45:04]    requested options: 1 3 6 7 12 15 26 28 42 43
[05/09/2024 14:45:04]    requested options: 1 3 6 7 12 15 26 28 42 43
[05/09/2024 14:45:04] Lookup client data for physical address "14-16-9D-E2-06-94" / client_id "14-16-9D-E2-06-94"
[05/09/2024 14:45:04] Lookup client data for physical address "14-16-9D-E2-06-94" / client_id "14-16-9D-E2-06-94"
[05/09/2024 14:45:04] Client 14-16-9D-E2-06-94 is configured with the IP address 192.168.1.4
[05/09/2024 14:45:04] Client 14-16-9D-E2-06-94 is configured with the IP address 192.168.1.4
[05/09/2024 14:45:04] Response: offer the configured IP address (lease time = 86400)
[05/09/2024 14:45:04] Response: offer the configured IP address (lease time = 86400)
[05/09/2024 14:45:04] Sending a broadcast response to the client
[05/09/2024 14:45:04] Connection 0: sending top queue packet
[05/09/2024 14:45:04] Sending a broadcast response to the client
[05/09/2024 14:45:04] Connection 0: sending top queue packet
[05/09/2024 14:46:06] Adapter 0 has recognized an incoming DHCP request
[05/09/2024 14:46:06] Adapter 0 has recognized an incoming DHCP request
[05/09/2024 14:46:06] DHCP message = DHCPDISCOVER
[05/09/2024 14:46:06] DHCP message = DHCPDISCOVER
[05/09/2024 14:46:06]    requested options: 1 3 6 7 12 15 26 28 42 43
[05/09/2024 14:46:06]    requested options: 1 3 6 7 12 15 26 28 42 43
[05/09/2024 14:46:06] Lookup client data for physical address "14-16-9D-E2-06-94" / client_id "14-16-9D-E2-06-94"
[05/09/2024 14:46:06] Lookup client data for physical address "14-16-9D-E2-06-94" / client_id "14-16-9D-E2-06-94"

 

 

 

In Wireshark:

ybp2000_0-1715281262463.png

If I replace the DHCP server with the Netgear R8000P Wi-Fi Router (just to use is as a router), then everything works fine.

What am I am missing in the setup with the DHCP server? 

 

8 Replies 8

marce1000
VIP
VIP

 

            - Check logs on the C9130AXI-B (too) , when trying to acquire an address ,

 M.



-- Each morning when I wake up and look into the mirror I always say ' Why am I so brilliant ? '
    When the mirror will then always repond to me with ' The only thing that exceeds your brilliance is your beauty! '

Hello,
Below is a part the log from the C9130AXI-B. 

The firewall is turned off on the Window machine running DHCP server. 

Thanks.



 

User Access Verification
Username:          Starting dnsmasq watcher...
         Starting DNSmasq...
[  OK  ] Started DNSmasq.
[  OK  ] Started dnsmasq watcher.
[  OK  ] Started RSYNC User Key Generation.
[  OK  ] Reached target sshd-keygen.target.
         Starting OpenSSH server daemon...
[  OK  ] Started OpenSSH server daemon.
[*09/21/2022 12:55:11.5662] wlan: [4414:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:11.5956] wlan: [4429:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:11.6091] Unable to load host key "/storage/ssh/ssh_host_ed25519_key": invalid format
[*09/21/2022 12:55:11.6125] Unable to load host key: /storage/ssh/ssh_host_ed25519_key
[*09/21/2022 12:55:11.6262] wlan: [4450:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:11.6567] wlan: [4472:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:11.6910] wlan: [4494:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:11.7245] wlan: [4513:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:11.7546] wlan: [4535:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:11.7946] wlan: [4556:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:11.8328] wlan: [4579:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:11.8634] wlan: [4598:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:11.8939] wlan: [4619:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:11.9246] wlan: [4641:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:11.9544] wlan: [4662:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:11.9864] wlan: [4683:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:12.0214] wlan: [4713:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:12.0593] wlan: [4733:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:12.1022] wlan: [4775:E:CMN_MLME] mlme_ext_vap_setup: Mesh vap not supported by this radio!!
[*09/21/2022 12:55:12.1022] wlan: [4775:E:CMN_MLME] mlme_ext_vap_create_pre_init: Unable to setup vap params
[*09/21/2022 12:55:12.1023] wlan: [4775:E:CMN_MLME] mlme_ext_vap_create: failed to create a vap object
[*09/21/2022 12:55:12.1023] wlan: [4775:I:ANY] wlan_vap_create: failed to create a vap object
[*09/21/2022 12:55:12.1023] 
[*09/21/2022 12:55:12.1023] wlan: [4775:E:CMN_MLME] mlme_vdev_ext_obj_create:  VDEV MLME legacy obj creation failed
[*09/21/2022 12:55:12.1023] wlan: [4775:E:CMN_MLME] mlme_vdev_obj_create_handler: Legacy vdev object creation failed
[*09/21/2022 12:55:12.1023] wlan: [4775:I:ANY] osifp_create_wlan_vap: VDEV (creation) failed 
[*09/21/2022 12:55:12.1024] wlan: [4775:I:ANY] osif_create_vap: wlan vap failed
[*09/21/2022 12:55:12.1024] 
[*09/21/2022 12:55:12.1024] wlan: [4775:I:ANY] wlan_cfg80211_add_virtual_intf: Failed to create VAP. osif_create_vap returned NULL!
[*09/21/2022 12:55:12.2408] wlan: [4831:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:12.2524] EEPROM Size = 65536
[*09/21/2022 12:55:12.2524] loading trx table from EEPROM to DTCM
[*09/21/2022 12:55:12.2524] 24480 bytes copied from RHL EEPROM to DTCM
[*09/21/2022 12:55:12.2524] EEPROM Size = 65536
[*09/21/2022 12:55:12.2524] loading ro1 table from EEPROM to DTCM
[*09/21/2022 12:55:12.2524] 12240 bytes copied from RHL EEPROM to DTCM
[*09/21/2022 12:55:12.2525] EEPROM Size = 65536
[*09/21/2022 12:55:12.2525] loading ro2 table from EEPROM to DTCM
[*09/21/2022 12:55:12.2525] 12240 bytes copied from RHL EEPROM to DTCM
[*09/21/2022 12:55:12.2769] wlan: [4849:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:12.3039] wlan: [4868:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:12.3432] wlan: [4894:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:12.3747] wlan: [4911:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:12.4073] wlan: [4932:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:12.4337] wlan: [4956:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:12.4710] wlan: [4982:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:12.5063] wlan: [4996:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:12.5339] wlan: [5017:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:12.5642] wlan: [5039:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:12.6033] wlan: [5064:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:12.6353] wlan: [5083:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:12.6635] wlan: [5102:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:12.6944] wlan: [5123:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:12.7235] wlan: [5143:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:12.7674] wlan: [5183:E:CMN_MLME] mlme_ext_vap_setup: Mesh vap not supported by this radio!!
[*09/21/2022 12:55:12.7674] wlan: [5183:E:CMN_MLME] mlme_ext_vap_create_pre_init: Unable to setup vap params
[*09/21/2022 12:55:12.7674] wlan: [5183:E:CMN_MLME] mlme_ext_vap_create: failed to create a vap object
[*09/21/2022 12:55:12.7674] wlan: [5183:I:ANY] wlan_vap_create: failed to create a vap object
[*09/21/2022 12:55:12.7674] 
[*09/21/2022 12:55:12.7675] wlan: [5183:E:CMN_MLME] mlme_vdev_ext_obj_create:  VDEV MLME legacy obj creation failed
[*09/21/2022 12:55:12.7675] wlan: [5183:E:CMN_MLME] mlme_vdev_obj_create_handler: Legacy vdev object creation failed
[*09/21/2022 12:55:12.7675] wlan: [5183:I:ANY] osifp_create_wlan_vap: VDEV (creation) failed 
[*09/21/2022 12:55:12.7675] wlan: [5183:I:ANY] osif_create_vap: wlan vap failed
[*09/21/2022 12:55:12.7675] 
[*09/21/2022 12:55:12.7676] wlan: [5183:I:ANY] wlan_cfg80211_add_virtual_intf: Failed to create VAP. osif_create_vap returned NULL!
[*09/21/2022 12:55:12.9000] wlan: [5239:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:12.9333] wlan: [5254:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:12.9640] wlan: [5278:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:12.9934] wlan: [5295:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:13.0240] wlan: [5318:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:13.0540] wlan: [5337:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:13.0841] wlan: [5359:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:13.1139] wlan: [5379:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:13.1439] wlan: [5404:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:13.1850] wlan: [5434:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:13.2153] wlan: [5450:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:13.2449] wlan: [5471:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:13.2766] wlan: [5492:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:13.3052] wlan: [5513:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:13.3349] wlan: [5535:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:13.3657] wlan: [5557:I:ANY] ieee80211_vap_setup: Disable vht SU BFEE by default in AP mode
[*09/21/2022 12:55:13.4328] wlan: [5608:E:CMN_MLME] mlme_ext_vap_setup: Mesh vap not supported by this radio!!
[*09/21/2022 12:55:13.4328] wlan: [5608:E:CMN_MLME] mlme_ext_vap_create_pre_init: Unable to setup vap params
[*09/21/2022 12:55:13.4328] wlan: [5608:E:CMN_MLME] mlme_ext_vap_create: failed to create a vap object
[*09/21/2022 12:55:13.4328] wlan: [5608:I:ANY] wlan_vap_create: failed to create a vap object
[*09/21/2022 12:55:13.4328] 
[*09/21/2022 12:55:13.4328] wlan: [5608:E:CMN_MLME] mlme_vdev_ext_obj_create:  VDEV MLME legacy obj creation failed
[*09/21/2022 12:55:13.4329] wlan: [5608:E:CMN_MLME] mlme_vdev_obj_create_handler: Legacy vdev object creation failed
[*09/21/2022 12:55:13.4329] wlan: [5608:I:ANY] osifp_create_wlan_vap: VDEV (creation) failed 
[*09/21/2022 12:55:13.4329] wlan: [5608:I:ANY] osif_create_vap: wlan vap failed
[*09/21/2022 12:55:13.4329] 
[*09/21/2022 12:55:13.4330] wlan: [5608:I:ANY] wlan_cfg80211_add_virtual_intf: Failed to create VAP. osif_create_vap returned NULL!
[*09/21/2022 12:55:15.0158] 
[*09/21/2022 12:55:15.0158] !!!!! {/opt/cisco/bin/capwap_brain} failed writing /click/vrrp_elector/preferred_ap_name len 0 data: ""
         Starting Lighttpd Watcher...
         Starting dnsmasq watcher...
         Stopping DNSmasq...
[  OK  ] Stopped DNSmasq.
         Starting DNSmasq...
[  OK  ] Started Lighttpd Watcher.
         Starting dhcpv6 client watcher...
[  OK  ] Started DNSmasq.
[*09/21/2022 12:55:15.2252] ip6_port srcr2, ip6local ::, ip6 ::, plen 0, gw6 ::, gw6_mac 00:00:00:00:00:00, mtu 1500, vid 0, mode6 2(slaac)
         Starting DHCPv6 client...
[  OK  ] Started dnsmasq watcher.
[  OK  ] Started DHCPv6 client.
[  OK  ] Started capwapd.
[  OK  ] Started dhcpv6 client watcher.
[*09/21/2022 12:55:15.6716] device aptrace0 entered promiscuous mode
[*09/21/2022 12:55:15.7810] pid 6168's current affinity mask: f
[*09/21/2022 12:55:15.7811] pid 6168's new affinity mask: 3
[  OK  ] Started gRPC server daemon.
[  OK  ] Started Clean Air daemon.
[*09/21/2022 12:55:16.1303] tri_radio mode is enabled
[*09/21/2022 12:55:16.1813] chpasswd: password for user changed
[  OK  ] Started WCPD process.
[*09/21/2022 12:55:16.5905] USB Device Disconnected from the AP
[*09/21/2022 12:55:16.9801] WCP: Opening /var/platform/num_wan_ports failed!
[*09/21/2022 12:55:17.0136] DOT11_TXP[0]:Domain configured: 0 class:A
[*09/21/2022 12:55:17.0642] DOT11_TXP[2]:Domain configured: 41 class:B
[*09/21/2022 12:55:17.5057] DOT11_TXP[1]:Domain configured: 41 class:B
[  OK  ] Started Security Auditing Service.
[*09/21/2022 12:55:18.4397] DOT11_DRV[3]: Skip Radio3, driver is not implemented - wcp/RadDrv3 :: Dot11AthDriverNL80211
[*09/21/2022 12:55:18.4610] flags value is 0 process ble_init
[*09/21/2022 12:55:18.4922] DOT11_DRV[1]: vendor_set_slot_capability: slot 1, radio_service_type 1
[*09/21/2022 12:55:18.4923] DOT11_DRV[1]: Init Radio1
[*09/21/2022 12:55:18.5256] DOT11_DRV[1]: set_channel Channel set to 36
[*09/21/2022 12:55:18.5287] DOT11_DRV[2]: vendor_set_slot_capability: slot 2, radio_service_type 0
[*09/21/2022 12:55:18.5287] DOT11_DRV[2]: Init Radio2
[*09/21/2022 12:55:18.5620] DOT11_DRV[2]: set_channel Channel set to 165
[*09/21/2022 12:55:18.5746] DOT11_DRV[0]: vendor_set_slot_capability: slot 0, radio_service_type 0
[*09/21/2022 12:55:18.5747] DOT11_DRV[0]: Init Radio0
[*09/21/2022 12:55:18.6033] DOT11_DRV[0]: set_channel Channel set to 6
[*09/21/2022 12:55:18.6059] DOT11_DRV[3]: vendor_set_slot_capability: slot 3, radio_service_type 0
[*09/21/2022 12:55:18.6149] DOT11_DRV[4]: off_channel timeout but no req in progress
[*09/21/2022 12:55:19.5023] DOT11_CFG[0] Radio Mode is changed from Local to FlexConnect
[*09/21/2022 12:55:19.5029] DOT11_CFG[0]: Starting radio 0
[*09/21/2022 12:55:19.5036] DOT11_DRV[0]: Start Radio0 - Begin
[*09/21/2022 12:55:19.5052] DOT11_DRV[0]: Start Radio0 - End
[*09/21/2022 12:55:19.5496] DOT11_CFG[1] Radio Mode is changed from Local to FlexConnect
[*09/21/2022 12:55:19.5505] DOT11_CFG[1]: Starting radio 1
[*09/21/2022 12:55:19.5517] DOT11_DRV[1]: Start Radio1 - Begin
[*09/21/2022 12:55:19.5532] DOT11_DRV[1]: Start Radio1 - End
[*09/21/2022 12:55:19.5971] DOT11_CFG[2] Radio Mode is changed from Local to FlexConnect
[*09/21/2022 12:55:19.5976] DOT11_CFG[2]: Starting radio 2
[*09/21/2022 12:55:19.5986] DOT11_DRV[2]: Start Radio2 - Begin
[*09/21/2022 12:55:19.6001] DOT11_DRV[2]: Start Radio2 - End
sensord psage_base init: RHB Sage base ptr 29030000
[*09/21/2022 12:55:19.9840] DOT11_DRV[0]: Stop Radio0 - Begin
[*09/21/2022 12:55:19.9885] DOT11_DRV[0]: Stop Radio0 - End
[*09/21/2022 12:55:20.0819] DOT11_DRV[0]: set_channel Channel set to 1
[*09/21/2022 12:55:20.0843] DOT11_DRV[0]: Start Radio0 - Begin
[*09/21/2022 12:55:20.0855] DOT11_DRV[0]: Start Radio0 - End
[*09/21/2022 12:55:20.1094] DOT11_DRV[0]: Stop Radio0 - Begin
[*09/21/2022 12:55:20.1143] DOT11_DRV[0]: Stop Radio0 - End
[*09/21/2022 12:55:20.3179] DOT11_DRV[0]: set_channel Channel set to 1
[*09/21/2022 12:55:20.3204] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:20.3204] DOT11_DRV[0]: vap Id 0 set TWT Support to disable, failed
[*09/21/2022 12:55:20.3205] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:20.3205] DOT11_DRV[0]: vap Id 1 set TWT Support to disable, failed
[*09/21/2022 12:55:20.3207] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:20.3207] DOT11_DRV[0]: vap Id 2 set TWT Support to disable, failed
[*09/21/2022 12:55:20.3208] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:20.3208] DOT11_DRV[0]: vap Id 3 set TWT Support to disable, failed
[*09/21/2022 12:55:20.3208] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:20.3209] DOT11_DRV[0]: vap Id 4 set TWT Support to disable, failed
[*09/21/2022 12:55:20.3209] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:20.3210] DOT11_DRV[0]: vap Id 5 set TWT Support to disable, failed
[*09/21/2022 12:55:20.3211] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:20.3211] DOT11_DRV[0]: vap Id 6 set TWT Support to disable, failed
[*09/21/2022 12:55:20.3212] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:20.3212] DOT11_DRV[0]: vap Id 7 set TWT Support to disable, failed
[*09/21/2022 12:55:20.3212] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:20.3213] DOT11_DRV[0]: vap Id 8 set TWT Support to disable, failed
[*09/21/2022 12:55:20.3213] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:20.3213] DOT11_DRV[0]: vap Id 9 set TWT Support to disable, failed
[*09/21/2022 12:55:20.3214] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:20.3215] DOT11_DRV[0]: vap Id 10 set TWT Support to disable, failed
[*09/21/2022 12:55:20.3215] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:20.3216] DOT11_DRV[0]: vap Id 11 set TWT Support to disable, failed
[*09/21/2022 12:55:20.3216] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:20.3216] DOT11_DRV[0]: vap Id 12 set TWT Support to disable, failed
[*09/21/2022 12:55:20.3217] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:20.3217] DOT11_DRV[0]: vap Id 13 set TWT Support to disable, failed
[*09/21/2022 12:55:20.3218] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:20.3218] DOT11_DRV[0]: vap Id 14 set TWT Support to disable, failed
[*09/21/2022 12:55:20.3219] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:20.3219] DOT11_DRV[0]: vap Id 15 set TWT Support to disable, failed
[*09/21/2022 12:55:20.3219] DOT11_DRV[0]: Radio 0 set HE/802.11ax TWT to disable, failed
[*09/21/2022 12:55:20.3222] DOT11_DRV[0]: Start Radio0 - Begin
[*09/21/2022 12:55:20.3236] DOT11_DRV[0]: Start Radio0 - End
[*09/21/2022 12:55:20.3449] DOT11_DRV[0]: Channel set to 1, width 20
[*09/21/2022 12:55:20.3450] DOT11_DRV[0]: Channel set to 1 skipped
[*09/21/2022 12:55:20.4303] DOT11_DRV[0]: Stop Radio0 - Begin
[*09/21/2022 12:55:20.4347] DOT11_DRV[0]: Stop Radio0 - End
[*09/21/2022 12:55:20.4868] wlan: [0:I:ANY] ol_ath_twt_disable_complete_event_handler: twt disabled
[*09/21/2022 12:55:20.5415] DOT11_DRV[0]: Channel set to 1, width 20
[*09/21/2022 12:55:20.5415] DOT11_DRV[0]: Channel set to 1 skipped
[*09/21/2022 12:55:20.6769] DOT11_DRV[1]: Stop Radio1 - Begin
[*09/21/2022 12:55:20.6817] DOT11_DRV[1]: Stop Radio1 - End
[*09/21/2022 12:55:20.7825] DOT11_DRV[1]: set_channel Channel set to 108
[*09/21/2022 12:55:20.7948] DOT11_DRV[1]: Start Radio1 - Begin
[*09/21/2022 12:55:20.7963] DOT11_DRV[1]: Start Radio1 - End
[*09/21/2022 12:55:20.8206] DOT11_DRV[1]: Stop Radio1 - Begin
[*09/21/2022 12:55:20.8252] DOT11_DRV[1]: Stop Radio1 - End
[*09/21/2022 12:55:20.8255] DOT11_DRV[1]: Start Radio1 - Begin
[*09/21/2022 12:55:20.8269] DOT11_DRV[1]: Start Radio1 - End
[*09/21/2022 12:55:20.8521] DOT11_DRV[1]: Stop Radio1 - Begin
[*09/21/2022 12:55:20.8568] DOT11_DRV[1]: Stop Radio1 - End
[*09/21/2022 12:55:20.8588] DOT11_DRV[1]: set_channel Channel set to 108
[*09/21/2022 12:55:20.8621] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:20.8622] DOT11_DRV[1]: vap Id 0 set TWT Support to disable, failed
[*09/21/2022 12:55:20.8623] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:20.8623] DOT11_DRV[1]: vap Id 1 set TWT Support to disable, failed
[*09/21/2022 12:55:20.8624] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:20.8624] DOT11_DRV[1]: vap Id 2 set TWT Support to disable, failed
[*09/21/2022 12:55:20.8625] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:20.8717] DOT11_DRV[1]: vap Id 3 set TWT Support to disable, failed
[*09/21/2022 12:55:20.8719] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:20.8720] DOT11_DRV[1]: vap Id 4 set TWT Support to disable, failed
[*09/21/2022 12:55:20.8720] wlan: [0:I:ANY] ol_ath_twt_disable_complete_event_handler: twt disabled
[*09/21/2022 12:55:20.8721] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:20.8721] DOT11_DRV[1]: vap Id 5 set TWT Support to disable, failed
[*09/21/2022 12:55:20.8722] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:20.8722] DOT11_DRV[1]: vap Id 6 set TWT Support to disable, failed
[*09/21/2022 12:55:20.8723] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:20.8723] DOT11_DRV[1]: vap Id 7 set TWT Support to disable, failed
[*09/21/2022 12:55:20.8724] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:20.8724] DOT11_DRV[1]: vap Id 8 set TWT Support to disable, failed
[*09/21/2022 12:55:20.8725] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:20.8725] DOT11_DRV[1]: vap Id 9 set TWT Support to disable, failed
[*09/21/2022 12:55:20.8725] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:20.8726] DOT11_DRV[1]: vap Id 10 set TWT Support to disable, failed
[*09/21/2022 12:55:20.8726] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:20.8727] DOT11_DRV[1]: vap Id 11 set TWT Support to disable, failed
[*09/21/2022 12:55:20.8727] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:20.8728] DOT11_DRV[1]: vap Id 12 set TWT Support to disable, failed
[*09/21/2022 12:55:20.8728] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:20.8728] DOT11_DRV[1]: vap Id 13 set TWT Support to disable, failed
[*09/21/2022 12:55:20.8729] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:20.8729] DOT11_DRV[1]: vap Id 14 set TWT Support to disable, failed
[*09/21/2022 12:55:20.8730] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:20.8730] DOT11_DRV[1]: vap Id 15 set TWT Support to disable, failed
[*09/21/2022 12:55:20.8730] DOT11_DRV[1]: Radio 1 set HE/802.11ax TWT to disable, failed
[*09/21/2022 12:55:20.8733] DOT11_DRV[1]: Start Radio1 - Begin
[*09/21/2022 12:55:20.8748] DOT11_DRV[1]: Start Radio1 - End
[*09/21/2022 12:55:20.8989] DOT11_DRV[1]: Channel set to 108, width 40
[*09/21/2022 12:55:20.8990] DOT11_DRV[1]: Channel set to 108 skipped
[*09/21/2022 12:55:20.9057] DOT11_DRV[1]: Stop Radio1 - Begin
[*09/21/2022 12:55:20.9106] DOT11_DRV[1]: Stop Radio1 - End
[*09/21/2022 12:55:20.9130] DOT11_DRV[1]: Start Radio1 - Begin
[*09/21/2022 12:55:20.9145] DOT11_DRV[1]: Start Radio1 - End
[*09/21/2022 12:55:20.9394] DOT11_DRV[1]: Channel set to 108, width 40
[*09/21/2022 12:55:20.9395] DOT11_DRV[1]: Channel set to 108 skipped
[*09/21/2022 12:55:21.0769] DOT11_DRV[2]: Stop Radio2 - Begin
[*09/21/2022 12:55:21.0818] DOT11_DRV[2]: Stop Radio2 - End
[*09/21/2022 12:55:21.1818] DOT11_DRV[2]: set_channel Channel set to 64
[*09/21/2022 12:55:21.1841] DOT11_DRV[2]: Start Radio2 - Begin
[*09/21/2022 12:55:21.1854] DOT11_DRV[2]: Start Radio2 - End
[*09/21/2022 12:55:21.2086] DOT11_DRV[2]: Stop Radio2 - Begin
[*09/21/2022 12:55:21.2131] DOT11_DRV[2]: Stop Radio2 - End
[*09/21/2022 12:55:21.2134] DOT11_DRV[2]: Start Radio2 - Begin
[*09/21/2022 12:55:21.2235] DOT11_DRV[2]: Start Radio2 - End
[*09/21/2022 12:55:21.2468] DOT11_DRV[2]: Stop Radio2 - Begin
[*09/21/2022 12:55:21.2513] DOT11_DRV[2]: Stop Radio2 - End
[*09/21/2022 12:55:21.3618] DOT11_DRV[2]: set_channel Channel set to 64
[*09/21/2022 12:55:21.3643] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:21.3644] DOT11_DRV[2]: vap Id 0 set TWT Support to disable, failed
[*09/21/2022 12:55:21.3644] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:21.3644] DOT11_DRV[2]: vap Id 1 set TWT Support to disable, failed
[*09/21/2022 12:55:21.3645] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:21.3645] DOT11_DRV[2]: vap Id 2 set TWT Support to disable, failed
[*09/21/2022 12:55:21.3646] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:21.3646] DOT11_DRV[2]: vap Id 3 set TWT Support to disable, failed
[*09/21/2022 12:55:21.3647] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:21.3647] DOT11_DRV[2]: vap Id 4 set TWT Support to disable, failed
[*09/21/2022 12:55:21.3647] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:21.3648] DOT11_DRV[2]: vap Id 5 set TWT Support to disable, failed
[*09/21/2022 12:55:21.3648] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:21.3648] DOT11_DRV[2]: vap Id 6 set TWT Support to disable, failed
[*09/21/2022 12:55:21.3649] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:21.3649] DOT11_DRV[2]: vap Id 7 set TWT Support to disable, failed
[*09/21/2022 12:55:21.3650] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:21.3650] DOT11_DRV[2]: vap Id 8 set TWT Support to disable, failed
[*09/21/2022 12:55:21.3651] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:21.3651] DOT11_DRV[2]: vap Id 9 set TWT Support to disable, failed
[*09/21/2022 12:55:21.3651] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:21.3652] DOT11_DRV[2]: vap Id 10 set TWT Support to disable, failed
[*09/21/2022 12:55:21.3652] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:21.3653] DOT11_DRV[2]: vap Id 11 set TWT Support to disable, failed
[*09/21/2022 12:55:21.3653] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:21.3653] DOT11_DRV[2]: vap Id 12 set TWT Support to disable, failed
[*09/21/2022 12:55:21.3654] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:21.3654] DOT11_DRV[2]: vap Id 13 set TWT Support to disable, failed
[*09/21/2022 12:55:21.3655] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:21.3655] DOT11_DRV[2]: vap Id 14 set TWT Support to disable, failed
[*09/21/2022 12:55:21.3656] wlan: [6383:E:ANY] ieee80211_ucfg_setparam: TWT support disabled
[*09/21/2022 12:55:21.3656] DOT11_DRV[2]: vap Id 15 set TWT Support to disable, failed
[*09/21/2022 12:55:21.3656] DOT11_DRV[2]: Radio 2 set HE/802.11ax TWT to disable, failed
[*09/21/2022 12:55:21.3658] DOT11_DRV[2]: Start Radio2 - Begin
[*09/21/2022 12:55:21.3750] wlan: [0:I:ANY] ol_ath_twt_disable_complete_event_handler: twt disabled
[*09/21/2022 12:55:21.3766] DOT11_DRV[2]: Start Radio2 - End
[*09/21/2022 12:55:21.3995] DOT11_DRV[2]: Channel set to 64, width 40
[*09/21/2022 12:55:21.3995] DOT11_DRV[2]: Channel set to 64 skipped
[*09/21/2022 12:55:21.4055] DOT11_DRV[2]: Stop Radio2 - Begin
[*09/21/2022 12:55:21.4099] DOT11_DRV[2]: Stop Radio2 - End
[*09/21/2022 12:55:21.4122] DOT11_DRV[2]: Start Radio2 - Begin
[*09/21/2022 12:55:21.4134] DOT11_DRV[2]: Start Radio2 - End
[*09/21/2022 12:55:21.4373] DOT11_DRV[2]: Channel set to 64, width 40
[*09/21/2022 12:55:21.4373] DOT11_DRV[2]: Channel set to 64 skipped
[*09/21/2022 12:55:21.4912] Socket: Valid Element: wcp/wcp_db Handler: set_vlan_name_map Data: null Length: 10
sensord split_glue psage_base: RHB Sage base ptr 29030000
sensord split_glue sage_addr: RHB Sage base ptr 29030000
sensord crim: RHB Sage base ptr 29030000
[*09/21/2022 12:55:24.6332] AP is in good condition, BLE is off
[*09/21/2022 12:55:24.6332] Set radio wifi0 power 4 antenna chain 4 15 0
[*09/21/2022 12:55:24.6332] Set radio wifi1 power 4 antenna chain 8 255 0
[*09/21/2022 12:55:24.6332] Set radio wifi2 power 4 antenna chain 4 15 0
[*09/21/2022 12:55:26.0683] IOT Bootloader Flash Tool 1.4
[*09/21/2022 12:55:26.0683] Firmware upgrade initiated by ble_init
[*09/21/2022 12:55:26.0683] bundled_ver_split ['2', '7', '20']
[  OK  ] Started BLE init service.
[*09/21/2022 12:55:45.4554] OK
         Stopping Cisco syslog service...
[  OK  ] Stopped Cisco syslog service.
         Starting Cisco syslog service...
[  OK  ] Started Cisco syslog service.
[  OK  ] Started ME Install Script.
[  OK  ] Reached target Multi-User System.
[*09/21/2022 12:55:58.1234] chatter: tohost_virtual :: ToHost: device 'virtual' went down
Wed Sep 21 12:55:58 UTC 2022 Starting Controller...Please wait for a few minutes ....
Wed Sep 21 12:55:58 UTC 2022 Creating webauth tarball extract directory
Wed Sep 21 12:55:58 UTC 2022 IOSd monitor 7287 started
Wed Sep 21 12:55:58 UTC 2022 fromdev_wired0 count = 147
Failed to find module 'autofs4'
systemd 246 running in system mode. (+PAM +AUDIT +SELINUX +IMA -APPARMOR -SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL +XZ -LZ4 -ZSTD -SECCOMP +BLKID -ELFUTILS +KMOD -IDN2 -IDN -PCRE2 default-hierarchy=hybrid)
Detected virtualization container-other.
Detected architecture arm64.
Running with unpopulated /etc.
Initializing machine ID from random generator.
Populated /etc with preset unit settings.
Queued start job for default target BinOS.
system-check_storage.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling.
(This warning is only shown for the first unit using IP firewalling.)

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

           Cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706



Cisco IOS Software [Dublin], C9800-AP Software (C9800-AP-K9_IOSXE-UNIVERSALK9-M), Version 17.12.3, RELEASE SOFTWARE (fc7)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2024 by Cisco Systems, Inc.
Compiled Wed 20-Mar-24 15:44 by mcpre


This software version supports only Smart Licensing as the software licensing mechanism.


PLEASE READ THE FOLLOWING TERMS CAREFULLY. INSTALLING THE LICENSE OR
LICENSE KEY PROVIDED FOR ANY CISCO SOFTWARE PRODUCT, PRODUCT FEATURE,
AND/OR SUBSEQUENTLY PROVIDED SOFTWARE FEATURES (COLLECTIVELY, THE
"SOFTWARE"), AND/OR USING SUCH SOFTWARE CONSTITUTES YOUR FULL
ACCEPTANCE OF THE FOLLOWING TERMS. YOU MUST NOT PROCEED FURTHER IF YOU
ARE NOT WILLING TO BE BOUND BY ALL THE TERMS SET FORTH HEREIN.

Your use of the Software is subject to Cisco's General Terms and any 
relevant supplemental terms found at
https://www.cisco.com/site/us/en/about/legal/contract-experience/index.html.

You hereby acknowledge and agree that certain Software and/or features are
licensed for a particular term, that the license to such Software and/or
features is valid only for the applicable term and that such Software and/or
features may be shut down or otherwise terminated by Cisco after expiration
of the applicable license term (e.g., 90-day trial period). Cisco reserves
the right to terminate any such Software feature electronically or by any
other means available. While Cisco may provide alerts, it is your sole
responsibility to monitor your usage of any such term Software feature to
ensure that your systems and networks are prepared for a shutdown of the
Software feature.



FIPS: Flash Key Check : Key Not Found, FIPS Mode Not Enabled
platform initcisco C9130AXI-B (VXE) processor (revision VXE) with 160837K bytes of memory.
Processor board ID FJC24431E95
2048K bytes of non-volatile configuration memory.
1812516K bytes of physical memory.
100000K bytes of AP Images at ap_images:.
513300K bytes of Backup Controller Image at backup_image:.
7774207K bytes of virtual hard disk at bootflash:.
25000K bytes of Temp trace export at tmp_trace_export:.
Installation mode is BUNDLE 

%Default route without gateway, if not a point-to-point interface, may impact performance
Num of cpu cores     4
Maximum number of AP's supported   100
%Default route without gateway, if not a point-to-point interface, may impact performance
No such file


Press RETURN to get started!



User Access Verification

Username: Wed Sep 21 12:58:59 UTC 2022 Created controller running file: Wed Sep 21 12:58:59 UTC 2022

% Username:  timeout expired!

































WLC1416.9DE2.0694 con0 is now available





Press RETURN to get started.








User Access Verification

Username: 
% Username:  timeout expired!

































WLC1416.9DE2.0694 con0 is now available





Press RETURN to get started.








User Access Verification

Username: admin
Password: 

########################################################################################################
#                                                                                                      #
#      Welcome to the Cisco Catalyst C9800-AP Embedded Wireless Controller command line interface      #
#                                                                                                      #
# Please see command reference guide for the complete list of supported commands for this release:     #
# https://www.cisco.com/c/en/us/td/docs/wireless/embedded_wireless_controller_configuration_guide.html #
#                                                                                                      #
########################################################################################################

WLC1416.9DE2.0694>

 

 

balaji.bandi
Hall of Fame
Hall of Fame

 

If I replace the DHCP server with the Netgear R8000P Wi-Fi Router (just to use is as a router), then everything works fine.

 

If the DHCP Server works - this means Windows 11 DHCP Server and NetGear WIFI Router works ?

When you replace with same DHCP SERVER and Cisco AP ot working ?

is this for clients or AP not able to get DHCP ? may be i was not clear

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

AP not able to get the IP Address from the DHCP server

Rich R
VIP
VIP

Your server log says it's sending a DHCP offer but your Wireshark trace does not see that offer so either the server is lying or the offer has been dropped somewhere between your server and the capture.  Are there any ACLs or firewalls in the path?

No ACLs on the switch. No firewalls on the PC running DHCP server.

Then that implies your server is lying.  Did you get a packet capture on the switch to confirm the server actually sent the packets?

No Cables on Me
Level 1
Level 1

Looks like you are running EWC,  have you tried using the internal  DHCP server on the WLC and see if that works.  The AP and EWC is directly connected. 

 

Review Cisco Networking for a $25 gift card