Can we upgrade the 9800-40 running on 17.3.4c (with 9120 and 1562 APs) to 17.15.3 directly?As per the release notes I could see we can directly upgrade to 17.15.3 if there is no 9130 and 9124 APs.However, in a note in the release notes, it also menti...
Hello everyone,We are currently working on a hospitality Wi-Fi design that requires 100% coverage with a minimum signal strength of –65 dBm and SNR ≥ 30 dB across all guest rooms.Due to interior design constraints, the Cisco Catalyst C9105AXW-E is pr...
When implementing a solution for RFID and WAPs.- what software can be used for RF planning so I can determine WAP locations given a floor map? Cisco Spaces needs a license which I don't have, AirMagnet is discontinued, Cisco does have a predictive pl...
AP Impersonation setting causing APs to showing up as a rogue threat level. Is it necessary to have it enabled on an AP? We do not use lightweight APs. If it is disabled to get rid of the rogue threat levels in DNAC, what effect will it have? I can't...
So today I was testing a QR code to all for easier connections to our Guest Wifi, which see's around 3000 users a week. When I connected I got an error that the Network had security issues.So I immediately check on my laptop, no issue, find someone w...
I am doing WLAN / VLAN mapping in flex connect groups. Is there a way I can dynamically set the Flex-Connect VLAN via ISE? Will the same "Airespace-Interface-Name" parameter that I use for local WLANs work?
Hello, good afternoon, colleagues. I have a WLC 3504 and two AP models connected to provide Wi-Fi to my users (C9117AXI-A and AIR-AP1852I-A-K9). The problem is that the APs suddenly stop providing service. My WLC has version 8.10.196.0, and I think i...
I want to deploy a controller based WLAN in one of the campus buildings that is not wired to the main network. Can I use a Point-to-Point Mesh Link as a bridge to a regular controller based WLAN or does the remote WLAN APs have be part of a mesh netw...
Hello Cisco Community,I was hoping someone could help me figure out why my CW9178I's MIC is not being accepted by my 9800-L-F controller.All of my troubleshooting has lead me to believe that the AP cert if not being accepted due to being invalid/inac...
Hi,we recently purchased several wireless units, we set up an account and we are trying to install the license. We received amagic key but it doesn't work. Does anyone know what this license is and how to install it? Thanks
If 6Ghz is enabled on WLC ssid, the condition is 'WPA3 Enabled'. Then, should only WPA3 be enabled?Or I'm confused if WPA3 is enabled. If WPA3 is enabled and WI-FI7 is enabled, can I use it in WPA2 + WAP3 form as well? Regarding this, is there any re...
We have a Cisco 9800-40 running 17.12.5. We want to enable containment of rogue Access Points (not registered with the WLC or WLCs within the mobility group) broadcasting managed SSIDs or part of the SSID. We enabled rogue detection in the AP Join Pr...
Granting Microsoft Admin Consent to Cisco ApplicationNetwork admins can sign-in using the below link to grant admin permission to the Cisco application.https://login.microsoftonline.com/organizations/adminconsent?client_id=d1b29572-1b35-40cc-9152-a80...
Hi-We are looking to make a 1-to-1 swap/upgrade of our Access Points. Do I need an installer- or is just a matter of takign down one and putting up the other? Thoughts as to the scope of this work? Can it be done by a B&G Person in coordination with ...
Does anyone have the "HydrantID Server CA O1" certificate chain that is actually installed on a Meraki AP (MR52) 30.7.1 Software?The IdenTrust download site has the Hydrant Intermediate CA cert, but the thumbprint is different.https://www.identrust.c...
