Cisco Catalyst 9120AXE EWC cant Controller

wenli · ‎09-26-2023

Greetings,

I recently acquired four Cisco Catalyst 9120AXE EWC Access Points for deployment. I began by provisioning power to one of the Access Points using a power injector. Following this, I initiated a factory reset utilizing the power mode setting. Upon completion, I patiently waited for the status LED to turn green, indicating readiness. Subsequently, I established a connection to the Access Point via WLAN and accessed the web-based user interface.

Within the web interface, I proceeded to configure essential parameters such as hostname, username, password, management IP address, subnet mask, and the wireless LAN settings. However, upon completing the configuration, I encountered an issue where the Access Point failed to detect the controller. The Access Point status LED is now intermittently blinking red and green.

I have since posted my query on a forum seeking assistance with this matter.

Thank you for your attention and support.

Best regards,
Wen Xuan Li

balaji.bandi · ‎09-26-2023

 I encountered an issue where the Access Point failed to detect the controller. The Access Point status LED is now intermittently blinking red and green.

Do you have WLC in the area ? how is your AP on boarding progress - broacast ? option 43 ?

connect console cable and post complete logs

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

wenli · ‎09-27-2023

CASH1-AP02>HELO
5.0205HNDRC1a-1.0.38-163.162
CPU0
L1CD
MMUI
MMUA
CODE
ZBBS
MAIN
Boot Strap Register: 0x6fc7b
NVRAM memcfg 0x60607
DDR3-1600 CL11 total 2048MB 4 8bits part[s]

DDR test done successfully
CFE Version: 5
Verifying MASTER U-Boot...
Launching MASTER U-Boot version 0x0060 ...

____ _
/ ___|(_) ___ ___ ___
| | | |/ __| / __|/ _ \
| |___ | |\__ \| (__| (_) |
\____||_||___/ \___|\___/
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|

U-Boot 2017.09 (Jul 20 2023 - 17:38:14 -0700) Broadcom BCM49408

Board: VANC-e
I2C: ready
DRAM: 2 GiB
enable MMU ... OK
NAND: Status wait timeout: nandsts=0x0 mask=0x40000000, count=0
NAND ECC BCH-8, page size 4096 bytes, spare size used 216 bytes
1024 MiB
MMC:
SF: Detected mx25l6405d with page size 256 Bytes, erase size 4 KiB, total 8 MiB
In: serial
Out: serial
Err: serial
Platform: 4908
SF: Detected mx25l6405d with page size 256 Bytes, erase size 4 KiB, total 8 MiB
pmc_init:PMC using DQM mode
pmc_patch_4908:7 0 7c0438 3470346
Board IP address : 10.1.1.114:ffffff00
Host IP address : 10.1.1.1
Gateway IP address : 10.1.1.1
Run from flash/host/tftp (f/h/c) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : :
Default host ramdisk file name :
Default ramdisk store address :
Board Id (0-18) : VANC_54991
Number of MAC Addresses (1-32) : 11
Base MAC Address : 58:8b:1c:b6:7b:38
PSI Size (1-128) KBytes : 48
Enable Backup PSI [0|1] : 0
System Log Size (0-256) KBytes : 0
Auxillary File System Size Percent: 0
flow memory allocation (MB) : 43
buffer memory allocation (MB) : 16
DHD 0 memory allocation (MB) : 0
DHD 1 memory allocation (MB) : 0
DHD 2 memory allocation (MB) : 0
Partition 1 Size (MB) : 0M
Partition 2 Size (MB) : 0M
Partition 3 Size (MB) : 0M
Partition 4 Size (MB) (Data) : 4M

BootImage: MASTER
Found external PHY firmware image
MTDPART Str = (mtdparts=nand:1m(nvram),5888k(bootfs),-(fs))
Net: Registering Ethernet Driver.....
Broadcom BCM 4908 Ethernet driver 0.1
pmc_switch_power_up: Rgmii Tx clock zone1 enable 0 zone2 enable 0.
Setting SGMII Calibration value to 0x8
swap_pair = 0

Detecting PHYs...
84880 A0 ae02:5158 --> N/A
84881 A0 ae02:5150 --> N/A
84884 A0 ae02:5148 --> N/A
84884E A0 ae02:5168 --> N/A
84885 A0 ae02:5178 --> N/A
84886 A0 ae02:5170 --> N/A
84887 A0 ae02:5144 --> N/A
84888 A0 ae02:5140 --> N/A
84888E A0 ae02:5160 --> N/A
84888S A0 ae02:5174 --> N/A
84880 B0 ae02:5159 --> N/A
84881 B0 ae02:5151 --> N/A
84884 B0 ae02:5149 --> N/A
84884E B0 ae02:5169 --> N/A
84885 B0 ae02:5179 --> N/A
84886 B0 ae02:5171 --> N/A
84887 B0 ae02:5145 --> N/A
84888 B0 ae02:5141 --> N/A
84888E B0 ae02:5161 --> N/A
84888S B0 ae02:5175 --> N/A
84891 A0 3590:5090 --> N/A
54991 A0 3590:5094 --> N/A
54991E A0 3590:5098 --> N/A
84891L A0 3590:5080 --> N/A
54991L A0 3590:5084 --> N/A
54991EL A0 3590:5088 --> N/A
84892 A0 3590:50a0 --> N/A
54992 A0 3590:50a4 --> N/A
54992E A0 3590:50a8 --> N/A
84894 A0 3590:50b0 --> N/A
54994 A0 3590:50b4 --> N/A
54994E A0 3590:50b8 --> N/A
54991H A0 3590:50d0 --> N/A
54994H A0 3590:50f0 --> N/A
84891 B0 3590:5091 --> N/A
54991 B0 3590:5095 --> N/A
54991E B0 3590:5099 --> N/A
84891L B0 3590:5081 --> N/A
54991L B0 3590:5085 --> N/A
54991EL B0 3590:5089 --> 0x1f
84892 B0 3590:50a1 --> N/A
54992 B0 3590:50a5 --> N/A
54992E B0 3590:50a9 --> N/A
84894 B0 3590:50b1 --> N/A
54994 B0 3590:50b5 --> N/A
54994E B0 3590:50b9 --> N/A
54991H B0 3590:50d1 --> N/A
54994H B0 3590:50f1 --> N/A

Loading firmware into detected phys...
Firmware version: Blackfin B0 v02-02-03-2020-03-16
Loading firmware into phys: map=0x80000000
Halt the phys processors operation
Upload the firmware into the on-chip memory
100%
Reset the processors to start execution of the code in the on-chip memory
Verify that the processors are running: OK
Verify that the firmware has been loaded with good CRC: OK
Firmware loading completed successfully

Unsupported MII type: 0
bcm4908_eth-0
MAC: 58:8b:1c:b6:7b:38

Hit ESC key to stop autoboot: 0
Mounting UBI device fs
ubi0: attaching mtd3
MG link 1G
ubi0: scanning is finished
ubi0: attached mtd3 (name "mtd=2", size 1017 MiB)
ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
ubi0: VID header offset: 4096 (aligned 4096), data offset: 8192
ubi0: good PEBs: 4069, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 589751834
ubi0: available PEBs: 33, total reserved PEBs: 4036, PEBs reserved for bad PEB handling: 80
Load Addr 0x10000000
Mount UBIFS PARTITION part1 ...
Loading file 'part1/part.bin' to addr 0x10000000...
Done

Checking image signing.
Image signing verification success for part part1 continue to run...
Multi Image Header Found
Count = 0 Offset = 0x10000050 Len = 11199200
Count = 1 Offset = 0x10aae330 Len = 3624983
Count = 2 Offset = 0x10e23348 Len = 7202
Booting from Partition: part1
arg 0: 0x10000050
arg 1: 0x3000000
arg 2: 0x1800000
## Loading init Ramdisk from Legacy Image at 03000000 ...
Image Name: Simple Ramdisk Image
Created: 2022-08-11 0:34:38 UTC
Image Type: AArch64 Linux RAMDisk Image (lzma compressed)
Data Size: 3624919 Bytes = 3.5 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 01800000
Booting using the fdt blob at 0x1800000
load dtb from fixed memory location directly...
/memory = 0x80000000 bytes @ 0x0
Set Memory to 2147483648l
WARNING: Node's property /reserved-memory/dt_reserved_buffer is not defined
WARNING: Node's property /reserved-memory/dt_reserved_flow is not defined
Appending NVRAM to dtb, ret:0
Loaded DTB from 0x01800000 with size 7202l
Curr Boot Args: <NULL>
DTB Boot Args (coherent_pool=4M cpuidle_sysfs_switch pci=pcie_bus_safe rootwait crashkernel=128M@0M)
Bootargs set to setenv bootargs console=$consoledev,$baudrate activepart=part1 activeboot=0 bootver=0x60 boardid=0x3 forceboot=0 coherent_pool=4M cpuidle_sysfs_switch pci=pcie_bus_safe rootwait crashkernel=128M@0M $console $nandEcc $mtdparts ubi.mtd=fs apmode=me BOOT_DEBUG=0
Cleanup Complete.... ARMv8_secure_init_done!!!
Loading Ramdisk to 4fb30000, end 4fea4fd7 ... OK
reserving fdt memory region: addr=0 size=20000
Using Device Tree in place at 0000000001800000, end 0000000001804c21

Starting kernel ...

[01/01/1970 00:00:02.8590] hub 3-0:1.0: config failed, hub doesn't have any ports! (err -19)
[01/01/1970 00:00:02.9510] brcmboard registered
[*01/01/1970 00:00:14.0290] buginf() enabled.
[*01/01/1970 00:00:14.0360] Made it into bootsh: Aug 11 2022 00:10:33 T-24d9397ced0a4659b2d7c81901185234c3a17e4e-g24d9397c-aut
[*01/01/1970 00:00:22.9470] bootsh mini ramfs booted /bootpart/part1/ramfs_data_cisco.cpio.lzma

Welcome to Cisco.

Usage of this device is governed by Cisco's End User License Agreement,
available at:
http://www.cisco.com/c/en/us/td/docs/general/warranty/English/EU1KEN_.html.

Restricted Rights Legend

Use, duplication, or disclosure by the Government is subject to
restrictions as set forth in subparagraph (c) of the Commercial
Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and
subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

Cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

This product contains some software licensed under the
"GNU General Public License, version 2" provided with
ABSOLUTELY NO WARRANTY under the terms of
"GNU General Public License, version 2", available here:
http://www.gnu.org/licenses/old-licenses/gpl-2.0.html

This product contains some software licensed under the
"GNU Library General Public License, version 2" provided
with ABSOLUTELY NO WARRANTY under the terms of "GNU Library
General Public License, version 2", available here:
http://www.gnu.org/licenses/old-licenses/lgpl-2.0.html

This product contains some software licensed under the
"GNU Lesser General Public License, version 2.1" provided
with ABSOLUTELY NO WARRANTY under the terms of "GNU Lesser
General Public License, version 2.1", available here:
http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html

This product contains some software licensed under the
"GNU General Public License, version 3" provided with
ABSOLUTELY NO WARRANTY under the terms of
"GNU General Public License, Version 3", available here:
http://www.gnu.org/licenses/gpl.html.

This product contains some software licensed under the
"GNU Affero General Public License, version 3" provided
with ABSOLUTELY NO WARRANTY under the terms of
"GNU Affero General Public License, version 3", available here:
http://www.gnu.org/licenses/agpl-3.0.html.

[*01/01/1970 00:00:48.8780] init: ioctl(SIOCGIFHWADDR): wired0: No such device
[*01/01/1970 00:00:48.8810] init: ioctl(SIOCGIFHWADDR): wired0: No such device
[*01/01/1970 00:00:48.8830] init: ioctl(SIOCGIFHWADDR): wired0: No such device
[*01/01/1970 00:00:48.8860] init: ioctl(SIOCGIFHWADDR): wired0: No such device
Press S for a shell, or another magic key...

ګ▒▒&▒[H▒jCreated slice -.slice.
ң+L[W▒▒eached target Timers.
[ OK ] Listening on Delayed Shutdown Socket.
[ OK ] Reached target Sockets.
[ OK ] Created slice system.slice.
Starting Cisco UBIFS reformat/mount...
[*01/01/1970 00:00:53.3760] root: Cisco Axel file system mounting
[ OK ] Created slice system-serial\x2dgetty.slice.
[ OK ] Reached target Cisco File Systems (Pre).
[ OK ] Reached target Slices.
[ OK ] Created slice system-sshd\x2dkeygen.slice.
[ OK ] Started Cisco UBIFS reformat/mount.
Starting Cisco early mount...
[ OK ] Started Cisco early mount.
[ OK ] Reached target Local File Systems (Pre).
Starting Cisco system time setup...
[*09/02/2023 23:59:59.0090] Last reload time: Sep 2 23:59:59 2023
[*09/02/2023 23:59:59.0000] Setting system time Sat Sep 2 23:59:59 UTC 2023
Starting Cisco seed generation...
Starting Cisco fips check...
Starting Cisco platform file generation...
[*09/02/2023 23:59:59.3000] GCM-128 POST passed
[*09/02/2023 23:59:59.3000] GCM-256 POST passed
[*09/02/2023 23:59:59.4140] Auxiliary radio device detected
[ OK ] Started Cisco system time setup.
[ OK ] Started Cisco seed generation.
[ OK ] Started Cisco fips check.
[ OK ] Started Cisco platform file generation.
Starting Cisco btldr service...
[*09/02/2023 23:59:59.7300]
[*09/02/2023 23:59:59.7300] [9/2/2023 23:60:60] : Shadow is now in-synced with master
[ OK ] Started Cisco btldr service.
[ OK ] Reached target Local File Systems.
Starting Cisco S10 boot service...
[ OK ] Started Cisco system time saving.
[*09/03/2023 00:00:00.0710] 22
MH▒▒ Starting Cisco system time saving...
[*09/03/2023 00:00:00.1420] Active version: 17.6.4.56
[*09/03/2023 00:00:00.1430] Backup version: 0.0.0.0
Starting Cisco pkg i[09/03/2023 00:00:00.3080] bcmlibs: module license 'Proprietary' taints kernel.
[09/03/2023 00:00:00.3900] Disabling lock debugging due to kernel taint
nstall service...
[*09/03/2023 00:00:00.2930] Loading BCM modules ...
[*09/03/2023 00:00:00.2930] Ignore pptp.ko
[*09/03/2023 00:00:00.2960] Ignore pktflow.ko
[*09/03/2023 00:00:00.2980] Ignore pktrunner.ko
[*09/03/2023 00:00:00.3000] Load bcmlibs.ko
[*09/03/2023 00:00:00.4670] BCMLIBS loaded[09/03/2023 00:00:00.7790] bm_base_addr 0xffffffc006000000, size 67108864, bm_base_addr_phys 0x0000000006000000
[09/03/2023 00:00:00.8960] fm_base_addr 0xffffffc002e00000, size 12582912, fm_base_addr_phys 0x0000000002e00000
...
[*09/03/2023 00:00:00.4790] Load wlcsm.ko
[*09/03/2023 00:00:00.5020] Load rdp_fpm.ko
[*09/03/2023 00:00:00.5450] Load bdmf.ko
[*09/03/2023 00:00:00.5690] Load proclikefs.ko
[*09/03/2023 00:00:00.5870] Load rdpa_gpl.ko
[*09/03/2023 00:00:00.6060] Load rdpa_gpl_ext.ko
[*09/03/2023 00:00:00.6240] Load rdpa.ko
[*09/03/2023 00:00:00.6880] Load rdpa_usr.ko
[*09/03/2023 00:00:00.7080] Load rdpa_mw.ko
[*09/03/2023 00:00:01.0140] RDP Physical address=0x82200000 Virtual address = 0xffffff8001c80000
[*09/03/2023 00:00:01.0270] configure_runner: NATC keysize 0x100070 key element size 16 contextsize 0x400000 context element size 64
[*09/03/2023 00:00:01.0270] ++++Runner gso_de[09/03/2023 00:00:01.7270] Broadcom Command List Driver v1.0
sc_pool created successful[09/03/2023 00:00:01.8220] crossbar[0]: Allocated cb_idx=0 int_ep=0
[09/03/2023 00:00:01.8970] crossbar[0]: Add cb_idx=0 ext_ep=0 SERDES:6
[09/03/2023 00:00:01.9720]
[09/03/2023 00:00:01.9720] Detecting PHYs...
[09/03/2023 00:00:02.0500] Lift PHY at address 31 out of Reset by GPIO:31 Active Low
ly
[*09/03/2[09/03/2023 00:00:02.1460] 54991EL B0 3590:5089 --> 0x1f
[09/03/2023 00:00:02.2170]
[09/03/2023 00:00:02.2170] Loading firmware into detected PHYs...
[09/03/2023 00:00:02.2170]
[09/03/2023 00:00:02.3470] Firmware version: Blackfin B0 v02-02-03-2020-03-16
[09/03/2023 00:00:02.4300] Loading firmware into PHYs: map=0x80000000 count=1
[09/03/2023 00:00:02.5120] Halt the PHYs processors operation
[09/03/2023 00:00:02.5800] Upload the firmware into the on-chip memory
2%er_nat_cache_key_ptr=0xffffffc003700000
4%fffffc002e00000at_cache_context_ptr=0xf
6%nt_ptr=0xffffffc003200000ner_context_co
8%0000,virt_addr 0xffffff80018fe0000x82c3
9%/03/2023 00:00:01.5140]
13%5>; Allocating <15360> bufs; RDP enum <
14%ipinfo.ko 00:00:01.6710] Load ch
15%brcmchipinfo: brcm_chipinfo_init entry
17%cmd.ko023 00:00:01.6910] Load rdpa_
18%d cmdlist.ko:00:01.7170] Loa
19%0] Load bcm_enet.ko809
21%0 int_ep 0 to ext_ep 0 connect cb_idx:
23%idx:0 int_ep 1 to ext_ep 2 connect cb_
25%check... Starting Cisco act2
82%
[09/03/2023 00:00:05.6230] audit_printk_skb: 102 callbacks suppressed
84%/03/2023 00:00:05.6950]
87%/03/2023 00:00:05.7190]
88%co pkg install service./2023 00:00:05.8460]
100%
[09/03/2023 00:00:06.2670] Reset the processors to start execution of the code in the on-chip memory
[09/03/2023 00:00:06.3720] Verify that the processors are running: OK
[09/03/2023 00:00:06.9220] Verify that the firmware has been loaded with good CRC: OK
[09/03/2023 00:00:07.0090] Firmware loading completed successfully
[09/03/2023 00:00:07.0090]
[09/03/2023 00:00:07.1100] Adjusted SF2 SGPHY: sphy_ctrl=0x00010c1b
[09/03/2023 00:00:07.1930] getrcal for res select 5, int 661, ext 649, ratio 125 ratio1 140, rcal 8
[09/03/2023 00:00:07.2910] Setting SGMII Calibration value to 0x8
[09/03/2023 00:00:07.3610] PLL_PON(8051): 0x0210; TX_PON(8067): 0x0040; RX_PON(80b2): 0x0880
[09/03/2023 00:00:07.9890] dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
[ OK ] Started Cisco S10 boot service.
Starting Cisco marlin_sia module service...
[*09/03/2023 00:00:07.1830] NOTE: Using Port Grouping for IMP ports : [ 0 --> 4 ] [ 1, 2 --> 5 ] [ 3, 7 --> 8 ]
[*09/03/2023 00:00:07.9890] eth0: Down <58:8B:1C:B6:7B:38> <ExtSw P0, Logical 08> PHY_ID <0x0007f008:0x08: On-chip 1G GPHY> Cfg: ANG.1G; Down
[*09/03/2023 00:00:07.9890] eth1: Down <58:8B:1C:B6:7B:38> <ExtSw P1, Logical 09> PHY_ID <0x0007f009:0x09: On-chip 1G GPHY> Cfg: ANG.1G; Down
[*09/03/2023 00:00:07.9890] eth2: Down <58:8B:1C:B6:7B:38> <ExtSw P2, Logical 10> PHY_ID <0x0007f00a:0x0a: On-chip 1G GPHY> Cfg: ANG.1G; Down
[*09/03/2023 00:00:07.9890] eth3: Down <58:8B:1C:B6:7B:38> <ExtSw P3, Logical 11> PHY_ID <0x0007f00b:0x0b: On-chip 1G GPHY> Cfg: ANG.1G; Down
[*09/03/2023 00:00:07.9890] eth4: Down <58:8B:1C:B6:7B:38> <ExtSw P7, Logical 15>
[*09/03/2023 00:00:07.9890] Chip Port 9, CrossBar Port 0, PHY_ID <0x06100006:0x06: On-chip 2.5G SERDES> Cfg: ANG.2.5G; Down
[*09/03/2023 00:00:07.9890] PHY_ID <0x0388001f:0x1f:External Cascaded 10G EXT3> Cfg: ANG.2.5G; Down
[*09/03/2023 00:00:07.9890] ===> Activate Deep Green Mode
[*09/03/2023 00:00:07.9890] bcmswlpbk0 (Ext switch port: (Logical Port: Virtual link DOWN
[*09/03/2023 00:00:08.0710] bcm_enet_init:L2672 ENET system contructed and configured enet-kthrd thread
[*09/03/2023 00:00:08.0710] enet_kthread_handler:L326 Instantiating ENET thread
[*09/03/2023 00:00:08.0930] open </dev/fcache> error no 2
[*09/03/2023 00:00:08.0930] fcctl: failed to disable hw acceleration
[*09/03/2023 00:00:08.0930] fcctl: failed to configure Flow Cache
[*09/03/2023 00:00:08.0940] open </dev/fcache> error no 2
[*09/03/2023 00:00:08.0940] fcctl: failed to disable Flow Cache
[*09/03/2023 00:00:08.0950]
[*09/03/2023 00:00:08.0950] open </dev/fcache> error no 2
[*09/03/2023 00:00:08.0950] fcctl: failed to flush Flow Cache entries Broadcom Packet Flow Cache flushing the flows
[*09/03/2023 00:00:08.1100] Auto Detection of Serdes: Enabled
[*09/03/2023 00:00:08.1100] PHY Capabilities: 2.5GFD|1GFD|100MFD
[*09/03/2023 00:00:08.1100] Link is Down.
[*09/03/2023 00:00:08.5050]
[*09/03/2023 00:00:08.5050]
[*09/03/2023 00:00:08.5050]
[*09/03/2023 00:00:08.5050]
[*09/03/2023 00:00:08.5050] Authenticating ACT2 ID:C9120
[*09/03/2023 00:00:08.5050] Authenticating SN:FOC272448M6
[*09/03/2023 00:00:08.5060]
[*09/03/2023 00:00:08.5060] (ACT2Boot) Hardware is Cisco (c) authentic
[*09/03/2023 00:00:08.5060]
[*09/03/2023 00:00:08.5090] ret code = 0.
[*09/03/2023 00:00:08.5120] Seeding /dev/urandom from ACT2
[*09/03/2023 00:00:08.5150] wired0 Link encap:Ethernet HWaddr 58:8B:1C:B6:7B:38
[*09/03/2023 00:00:08.5150] UP BROADCAST MULTICAST MTU:2044 Metric:1
[*09/03/2023 00:00:08.5150] RX packets:131 errors:0 dropped:4 overruns:0 frame:0
[*09/03/2023 00:00:08.5150] TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
[*09/03/2023 00:00:08.5150] collisions:0 txqueuelen:1000
[*09/03/2023 00:00:08.5150] RX bytes:14559 (14.2 KiB) TX bytes:0 (0.0 B)
[*09/03/2023 00:00:08.5150]
[*09/03/2023 00:00:08.5170] 58:8B:1C:B6:7B:38
[*09/03/2023 00:00:08.5170] BCM11ax AP: MIC Certificate Present
[*09/02/2023 23:59:59.0070] Last reload time: Sep 2 23:59:59 2023
[*09/02/2023 23:59:59.0000] Setting system time Sat Sep 2 23:59:59 UTC 2023
[*09/02/2023 23:59:59.5390] Last reload reason : 0: unknown
[*09/03/2023 00:00:00.5860] Reading ACT2 SUDI certificates
Starting Cisco watchdog...
Starting Cisco nolan service...
Starting Cisco nss service...
[ OK ] Started Cisco watchdog.
[ OK ] Started Cisco nolan service.
[*09/03/2023 00:00:03.6490] <=== Deactivate Deep Green Mode
[*09/03/2023 00:00:03.6490] bcmswlpbk0 (Ext switch port: (Logical Port: Virtual link UP
[*09/03/2023 00:00:03.6490] wired0 (Ext switch port: 7) (Logical Port: 15) (phyId: 1f) Link Up at 1000 mbps full duplex
[ OK ] Started Cisco nss service.
Starting Cisco S15platform...
Starting Cisco Kclick...
Starting Cisco nolan USB service...
[*09/03/2023 00:00:04.0960] Loading HND Module
[ OK ] Started Cisco nolan USB service.
[ OK ] Started Cisco pre-PoE negotiation.
[*09/03/2023 00:00:04.2570] stile module dp init successfully
[*09/03/2023 00:00:04.2570] NBAR Label:BLD_POLARIS_DEV_LATEST_20200414_053707 Module timestamp: Aug 10 2022 at 23:37:34 User: ttaichol
Starting Cisco pre-PoE negotiation...
[ OK ] Started Cisco Kclick.
[*09/03/2023 00:00:04.6480]
[*09/03/2023 00:00:04.6480] ACT2 Check passed
[*09/03/2023 00:00[ OK ] Started Cisco act2 check.
[ OK ] Started Cisco marlin_sia module service.
[ OK ] Started Cisco S15platform.
Starting Cisco Sku service...
Starting Cisco certificate create service...
Starting Cisco ME service...
Starting Cisco Kclick...
Starting Cisco sysctl service...
[*09/03/2023 00:00:06.0230] Starting c[09/03/2023 00:00:06.4120] broadcomThermalDrv brcm-therm: init (CPU count 4 4 4 4)
heck if backup WiFi NVRAM are available
[*09/03/2023 00:00:06.0230] WiFi backup nvram - crc = 2417779407
[*09/03/2023 00:00:06.0230] WiFi active nvram - crc =617
[*09/03/2023 00:00:06.0230] [WARNING]ACTIVE and BACKUP NVRAM NOT use same data
[*09/03/2023 00:00:06.0420] restore done!
[*09/03/2023 00:00:06.0480] restore done!
[*09/03/2023 00:00:06.3530] sysctl: write error: Input/output error
[*09/03/2023 00:00:06.3820] MEMODE variable is already set - Just proceed
[*09/03/2023 00:00:06.7290] crypto worker thread started
[*09/03/2023 00:00:06.7320] crypto worker thread started
[*09/03/2023 00:00:06.7600] Broadcom EAP Forwarder v0.1 is loaded
[*09/03/2023 00:00:06.8090] igs_module_init:867: IGS 18 create network socket successful
[*09/03/2023 00:00:07.2180] Wifi Forwarding Driver is initialized!
[ OK ] Started Cisco Sku service.
[ OK ] Started Cisco certificate create service.
[ OK ] Started Cisco ME service.
[*09/03/2023 00:00:07.5280] wl_module_init: passivemode set to 0x1
[*09/03/2023 00:00:07.5280] wl_module_init: txworkq set to 0x0
[*09/03/2023 00:00:07.5280] wl_pktfwd_sys_init: WL_PKTFWD[1.1.0] Success
[*09/03/2023 00:00:07.5320] initvars_cis_pci: Not CIS format
[*09/03/2023 00:00:07.5330] sprom_read_pci: buf[0] = 0xffff, returning bad-crc
[*09/03/2023 00:00:07.5330] srom read failed
[*09/03/2023 00:00:07.5330] srom rev:0
[*09/03/2023 00:00:07.5360] BME Service Initialization
[*09/03/2023 00:00:07.5360] BME: M2M Core id 0x844 rev 3
[*09/03/2023 00:00:07.5370] wl0: phy_radio_attach: RF Band Cap: 2G:1 5G:1
[*09/03/2023 00:00:07.5660] BME:register key<1010802> user RLM sel IDX set 1 mem 2 8 hi 0 0
[*09/03/2023 00:00:07.5670] wl0 taf_do_enable: TAF is enabled
[*09/03/2023 00:00:07.5680]
[*09/03/2023 00:00:07.5680] WLC_ATTACH routine completed successfully
[*09/03/2023 00:00:07.5680] wfd0-thrd WL 0 FLowControl total<22369> lo<5592> hi<2236> favor prio<4>
[*09/03/2023 00:00:07.5690] wfd_bind: wfd0-thrd initialized pktlists: radio 0 nodes 4104 xfer wl_pktfwd_xfer_callback+0x0/0x298 [wl]
[*09/03/2023 00:00:07.5690]
[*09/03/2023 00:00:07.5690] Creating CPU ring for queue number 0 with 1024 packets descriptor=0xffffffbffd251680
[*09/03/2023 00:00:07.5690] Creating CPU ring for queue number 1 with 1024 packets descriptor=0xffffffbffd2516c0
[*09/03/2023 00:00:07.5690] wfd_bind: Dev apr1v0 wfd_idx 0 wl_radio_idx 0 Type skb:sll configured WFD thread wfd0-thrd minQId/maxQId (8/9), status (0) qmask 0x3
[*09/03/2023 00:00:07.5690] Instantiating WFD 0 thread
[*09/03/2023 00:00:07.5690] wl_wfd_bind: wl0 wfd_idx 0 success
[*09/03/2023 00:00:07.5700] eap_dev_g: initialized pktlists: radio 0 nodes 4104 xfer wl_pktfwd_xfer_callback+0x0/0x298 [wl]
[*09/03/2023 00:00:07.5700] 0 FlowControl total<22369> lo<5592> hi<2236> favor prio<4> enabled<1>
[*09/03/2023 00:00:07.5710] apr1v0: Broadcom BCM43684 802.11 Wireless Controller 17.20.10 (r790816 WLTEST)
[*09/03/2023 00:00:07.5740] initvars_cis_pci: Not CIS format
[*09/03/2023 00:00:07.5750] sprom_read_pci: buf[0] = 0xffff, returning bad-crc
[*09/03/2023 00:00:07.5750] srom read failed
[*09/03/2023 00:00:07.5750] srom rev:0
[*09/03/2023 00:00:07.5780] BME Service Initialization
[*09/03/2023 00:00:07.5780] BME: M2M Core id 0x844 rev 3
[*09/03/2023 00:00:07.5790] wl1: phy_radio_attach: RF Band Cap: 2G:1 5G:1
[*09/03/2023 00:00:07.6080] BME:register key<1010802> user RLM sel IDX set 1 mem 2 8 hi 0 0
[*09/03/2023 00:00:07.6090] wl1 taf_do_enable: TAF is enabled
[*09/03/2023 00:00:07.6100]
[*09/03/2023 00:00:07.6100] WLC_ATTACH routine completed successfully
[*09/03/2023 00:00:07.6100] wfd1-thrd WL 1 FLowControl total<22369> lo<5592> hi<2236> favor prio<4>
[*09/03/2023 00:00:07.6110] wfd_bind: wfd1-thrd initialized pktlists: radio 1 nodes 4104 xfer wl_pktfwd_xfer_callback+0x0/0x298 [wl]
[*09/03/2023 00:00:07.6110]
[*09/03/2023 00:00:07.6110] Creating CPU ring for queue number 2 with 1024 packets descriptor=0xffffffbffd251700
[*09/03/2023 00:00:07.6110] Creating CPU ring for queue number 3 with 1024 packets descriptor=0xffffffbffd251740
[*09/03/2023 00:00:07.6110] wfd_bind: Dev apr0v0 wfd_idx 1 wl_radio_idx 1 Type skb:sll configured WFD thread wfd1-thrd minQId/maxQId (10/11), status (0) qmask 0xc
[*09/03/2023 00:00:07.6110] Instantiating WFD 1 thread
[*09/03/2023 00:00:07.6110] wl_wfd_bind: wl1 wfd_idx 1 success
[*09/03/2023 00:00:07.6120] eap_dev_g: initialized pktlists: radio 1 nodes 4104 xfer wl_pktfwd_xfer_callback+0x0/0x298 [wl]
[*09/03/2023 00:00:07.6120] 1 FlowControl total<22369> lo<5592> hi<2236> favor prio<4> enabled<1>
[*09/03/2023 00:00:07.6130] apr0v0: Broadcom BCM43684 802.11 Wireless Controller 17.20.10 (r790816 WLTEST)
[ OK ] Started Cisco Kclick.
[ OK ] Started Cisco sysctl service.
Starting Cisco syslog service...
Starting Cisco S16platfomm...
Starting rsyslog client...
Starting Cisco certtime service...
[*09/03/2023 00:00:11.8730] pid 3495's current affinity mask: f
[*09/03/2023 00:00:11.8730] pid 3495's new affinity mask: e
[*09/03/2023 00:00:11.8750] pid 3491's current affinity mask: f
[*09/03/2023 00:00:11.8750] pid 3491's new affinity mask: e
[*09/03/2023 00:00:11.9300] wl: Not up
[*09/03/2023 00:00:11.9310] wl: Not up
[*09/03/2023 00:00:11.9380] wl: Bad Band
[*09/03/2023 00:00:11.9430] Success.
[*09/03/2023 00:00:11.9440] Success.
[ OK ] Started Tam server.
Starting Tam server...
[ OK ] Started Cisco Tam service.
Starting Cisco Tam service...
[ OK ] Started Cisco syslog service.
[ OK ] Started rsyslog client.
Starting Cisco synclogd...
[ OK ] Started Cisco S16platfomm.
Starting RHL daemon...
[ OK ] Started Cisco synclogd.
[09/03/2023 00:00:13.0480] NXP-RHL-Driver 0001:01:00.0: RHL: AP SKU = 1, pow min,max = -4, 20
[09/03/2023 00:00:13.0480] , Rx Diversity =0, 6g AP = 0, Ithaca Esku =0
[09/03/2023 00:00:13.2480] NXP-RHL-Driver 0001:01:00.0: Final VSPA image size val 0x1086000
[09/03/2023 00:00:14.1430] bcm963xx-pcie: RHL legacy interrupt initialized
[ OK ] Started RHL daemon.
[ **] A start job is running for Cisco certtime service (34s / 2min 23s)[*09/03/2023 00:00:12.8110] rhl_reset : got minor 55
[*09/03/2023 00:00:13.3390] V2H call back init
[*09/03/2023 00:00:13.3390] V2H callback registered
[*09/03/2023 00:00:14.2170]
[*09/03/2023 00:00:14.2170] Click sched monitor: schedulers = 1
[ *** ] A start job is running for Cisco certtime service (53s / 2min 23s)[09/03/2023 00:00:42.4690] audit_printk_skb: 45 callbacks suppressed
[ OK ] Started Cisco certtime service.
[ OK ] Reached target System Initialization.
j▒▒5▒j▒z▒Reachedi▒ju▒▒▒▒▒▒▒▒▒▒▒ɝ▒с▒ͥ▒▒▒▒▒ѕ▒▒jR▒ Starting Cisco brain service...
Starting Cisco image/firmware updater service...
[*09/03/2023 00:01:08.4710] watchdogd: reading file /click/wdog_helper/ap_monproc_kclick: No such file or directory
[*09/03/2023 00:01:08.4710]
[*09/03/2023 00:01:08.4710] !!!!! {watchdogd} reading /click/wdog_helper/ap_monproc_kclick failed [2]: No such file or directory
[*09/03/2023 00:01:08.4710]
[*09/03/2023 00:01:08.4710] !!!!! {watchdogd} Process kclick no heartbeat for 60s
[*09/03/2023 00:01:08.4710]
[*09/03/2023 00:01:08.4710] !!!!! {watchdogd} Process sxpd gone for 60s
[*09/03/2023 00:01:08.4750] watchdogd: reading file /tmp/brain_dump: No such file or directory
[*09/03/2023 00:01:08.4750] watchdogd: reading file /click/l2_l3_gateway/gateway_ip_addr: No such file or directory
[*09/03/2023 00:01:12.5800] starting tam services using ACT2...
[*09/03/2023 00:01:12.5800]
[*09/03/2023 00:01:12.5800] TAM init done
[*09/03/2023 00:01:13.4010]
[*09/03/2023 00:01:13.4010] [9/3/2023 0:2:14] updt_util: PHY firmware is up to date
[*09/03/2023 00:01:13.4090]
[*09/03/2023 00:01:13.4090] [9/3/2023 0:2:14] updt_util: All bootloaders are up to date
Starting Security Auditing Service...
Starting Cisco led service...
Starting Clean Air daemon...
Starting Cisco rtd service...
Starting Cisco klogd...
[ OK ] Started RHL monitor/reset daemon.
[*09/03/2023 00:01:14.8070] reset device opened
Starting RHL monitor/reset daemon...
Starting Hostapd process...
Starting ME Install Script...
[ OK ] Started Serial Getty on ttyS0.
j▒▒5▒j▒z▒Startini▒ju▒▒▒▒▒▒▒▒▒▒▒ɝ▒сb▒▒▒▒▒▒ɽ▒▒▒͹jR▒[ OK ] Started System Monitor service.
[*09/03/2023 00:01:15.2120] root: Systemd memory leak found Rss=8620, doing systemctl daemon-reexec
M▒▒ Starting System Monitor service...
Starting WCPD process...
Starting RSYNC User Key Generation...
Starting gRPC server daemon...
Starting capwapd...
Starting AP Trace daemon...
Starting Cisco kexec...
Starting Fast CGI daemon...
Starting BLE init service...
Starting Cisco printkd...
Starting Sensord daemon...
[ OK ] Started NTP_PROC daemon.
Starting NTP_PROC daemon...
[ OK ] Started Cisco image/firmware updater service.
[ OK ] Started Cisco led service.
[ OK ] Started Cisco klogd.
[ OK ] Started Cisco kexec.
[ OK ] Started BLE init service.
[ OK ] Started Cisco printkd.
[*09/03/2023 00:01:16.2830] Failed to get properties: Connection reset by peer
[*09/03/2023 00:01:16.2920] Failed to get properties: Connection reset by peer
[*09/03/2023 00:01:16.3810] Failed to get properties: Connection reset by peer
[*09/03/2023 00:01:16.3820] Failed to get properties: Connection reset by peer
[*09/03/2023 00:01:16.3830] Failed to get properties: Connection reset by peer
[*09/03/2023 00:01:16.3840] Failed to get properties: Connection reset by peer
[ OK ] Started Cisco rtd service.
[*09/03/2023 00:01:16.5100] hostapd:Hostapd: DCDS not init cloud=0 webauth=255 255 init=0
[*09/03/2023 00:01:16.5100]
[ OK ] Started Hostapd process.
[*09/03/2023 00:01:16.5440] EEPROM Size = 65536
[*09/03/2023 00:01:16.5440] loading pow table from EEPROM to scratch buf
[*09/03/2023 00:01:16.5440] 10200 bytes copied from RHL EEPROM to scratch buf
Starting ntp file watcher...
[ OK ] Started AP Trace daemon.
[ OK ] Started Fast CGI daemon.
[*09/03/2023 00:01:16.6370] No valid NTP source
[*09/03/2023 00:01:16.6370] No valid ntp server info file. Stop NTP!
Starting ntp watcher...
[ OK ] Started Sensord daemon.
[ OK ] Started ntp file watcher.
[ OK ] Started ntp watcher.
[ OK ] Started Cisco brain service.
Starting dnsmasq watcher...
Starting DNSmasq...

[ OK ] Started DNSmasq.
[ OK ] Started dnsmasq watcher.

User Access Verification
Username: [*09/03/2023 00:01:17.8860] click-config/io-real.click:382: While configuring 'todev_wired0 :: ToDevice':
[*09/03/2023 00:01:17.8860] warning: device 'wired0' is down
[*09/03/2023 00:01:18.0600] click-config/io-real.click:382: While configuring 'fromdev_wired0 :: FromWiredSwNssDevice':
[*09/03/2023 00:01:18.0600] warning: device 'wired0' is down
[*09/03/2023 00:01:18.2100] wired0 (Ext switch port: 7) (Logical Port: 15) (phyId: 1f) Link DOWN.
[*09/03/2023 00:01:18.2100] ===> Activate Deep Green Mode
[*09/03/2023 00:01:18.2100] bcmswlpbk0 (Ext switch port: (Logical Port: Virtual link DOWN
[*09/03/2023 00:01:18.4410] click-config/io-real.click:382: While initializing 'tohost_wired0 :: ToHost':
[*09/03/2023 00:01:18.4410] warning: device 'wired0' is down
[*09/03/2023 00:01:18.6230]
[*09/03/2023 00:01:18.6230] !!!!! {/opt/cisco/bin/capwap_brain} failed writing /click/vrrp_elector/preferred_ap_name len 0 data: ""
Starting Lighttpd Watcher...
[ OK ] Started Lighttpd Watcher.
[ OK ] Started capwapd.
Starting dnsmasq watcher...
Stopping DNSmasq...
[ OK ] Stopped DNSmasq.
Starting DNSmasq...
[*09/03/2023 00:01:18.8090] EEPROM Size = 65536
[*09/03/2023 00:01:18.8090] loading trx table from EEPROM to DTCM
[*09/03/2023 00:01:18.8090] 24480 bytes copied from RHL EEPROM to DTCM
[*09/03/2023 00:01:18.8090] EEPROM Size = 65536
[*09/03/2023 00:01:18.8090] loading ro1 table from EEPROM to DTCM
[*09/03/2023 00:01:18.8090] 12240 bytes copied from RHL EEPROM to DTCM
[*09/03/2023 00:01:18.8090] EEPROM Size = 65536
[*09/03/2023 00:01:18.8090] loading ro2 table from EEPROM to DTCM
[*09/03/2023 00:01:18.8090] 12240 bytes copied from RHL EEPROM to DTCM
[ OK ] Started DNSmasq.
Starting dhcpv6 client watcher...
[*09/03/2023 00:01:18.9140] ip6_port srcr2, ip6local ::, ip6 ::, plen 0, gw6 ::, gw6_mac 00:00:00:00:00:00, mtu 1500, vid 0, mode6 2(slaac)
Starting DHCPv6 client...
[ OK ] Started dnsmasq watcher.
[ OK ] Started DHCPv6 client.
[ OK ] Started dhcpv6 client watcher.
[ OK ] Started Clean Air daemon.
[*09/03/2023 00:01:19.3050] chpasswd: password for user changed
[*09/03/2023 00:01:19.3140] <=== Deactivate Deep Green Mode
[*09/03/2023 00:01:19.3140] bcmswlpbk0 (Ext switch port: (Logical Port: Virtual link UP
[*09/03/2023 00:01:19.3140] wired0 (Ext switch port: 7) (Logical Port: 15) (phyId: 1f) Link Up at 1000 mbps full duplex
[*09/03/2023 00:01:19.8080] pid 5873's current affinity mask: f
[*09/03/2023 00:01:19.8080] pid 5873's new affinity mask: 2
[*09/03/2023 00:01:19.8740] capwapd: reading file /click/nss_lag_control/lacp_state: No such file or directory
[*09/03/2023 00:01:19.8750]
[*09/03/2023 00:01:19.8750] !!!!! {/opt/cisco/bin/capwapd} reading /click/nss_lag_control/lacp_state failed [2]: No such file or directory
[*09/03/2023 00:01:19.8750] capwapd: reading file /click/nss_lag_control/capwap_state: No such file or directory
[*09/03/2023 00:01:19.8750]
[*09/03/2023 00:01:19.8750] !!!!! {/opt/cisco/bin/capwapd} reading /click/nss_lag_control/capwap_state failed [2]: No such file or directory
[ OK ] Started gRPC server daemon.
[ OK ] Started RSYNC User Key Generation.
[ OK ] Reached target sshd-keygen.target.
Starting OpenSSH server daemon...
[ OK ] Started OpenSSH server daemon.
[ OK ] Started WCPD process.
[*09/03/2023 00:01:21.3760] WCP: Opening /var/platform/num_wan_ports failed!
[*09/03/2023 00:01:21.4060] DOT11_TXP[0]:Domain configured: 41 class:B
[*09/03/2023 00:01:21.7820] DOT11_TXP[0]:Domain configured: 41 class:B
[*09/03/2023 00:01:22.1700] DOT11_TXP[0]:Domain configured: 0 class:A
[*09/03/2023 00:01:23.4410] DOT11_DRV[0]: BCM FIPS POST for CCMP-128 and GCMP-128 passed
[*09/03/2023 00:01:23.4410] DOT11_DRV[0]: Stop Radio0
[*09/03/2023 00:01:23.4410] Stopped Radio 0
[*09/03/2023 00:01:23.4670] US (US/0) UNITED STATES
[*09/03/2023 00:01:23.4730] DOT11_DRV[0]: set_channel Channel set to 6/20
[ OK ] Started Security Auditing Service.
[*09/03/2023 00:01:24.6730] DOT11_DRV[1]: BCM FIPS POST for CCMP-128 and GCMP-128 passed
[*09/03/2023 00:01:24.6730] DOT11_DRV[1]: Stop Radio1
[*09/03/2023 00:01:24.6730] Stopped Radio 1
[*09/03/2023 00:01:24.6980] US (US/0) UNITED STATES
[*09/03/2023 00:01:24.7040] DOT11_DRV[1]: set_channel Channel set to 36/20
[*09/03/2023 00:01:25.5850] DOT11_DRV[2]: off_channel timeout but no req in progress
[*09/03/2023 00:01:25.6010] DOT11_CFG[0] Radio Mode is changed from Local to FlexConnect
[*09/03/2023 00:01:25.6020] DOT11_CFG[0]: Starting radio 0
[*09/03/2023 00:01:25.6030] DOT11_DRV[0]: Start Radio0
[*09/03/2023 00:01:25.6110] DOT11_DRV[0]: set_channel Channel set to 6/20
[*09/03/2023 00:01:26.0150] Started Radio 0
[*09/03/2023 00:01:26.0240] DOT11_CFG[1] Radio Mode is changed from Local to FlexConnect
[*09/03/2023 00:01:26.0250] DOT11_CFG[1]: Starting radio 1
[*09/03/2023 00:01:26.0250] DOT11_DRV[1]: Start Radio1
[*09/03/2023 00:01:26.0320] DOT11_DRV[1]: set_channel Channel set to 36/20
[*09/03/2023 00:01:26.4190] Started Radio 1
sensord psage_base init: RHB Sage base ptr a1030000
[*09/03/2023 00:01:27.5180] size: 17504 bytes (48032 left)
[*09/03/2023 00:01:27.7710] DOT11_DRV[0]: Stop Radio0
[*09/03/2023 00:01:27.7720] Stopped Radio 0
[*09/03/2023 00:01:27.7980] DOT11_DRV[0]: Start Radio0
[*09/03/2023 00:01:27.8040] DOT11_DRV[0]: set_channel Channel set to 1/20
[*09/03/2023 00:01:28.2020] Started Radio 0
[*09/03/2023 00:01:28.2020] DOT11_DRV[0]: set_channel Channel set to 1/20
[*09/03/2023 00:01:28.2500] wl: Unsupported
sensord split_glue psage_base: RHB Sage base ptr a1030000
sensord split_glue sage_addr: RHB Sage base ptr a1030000
sensord crim: RHB Sage base ptr a1030000
[*09/03/2023 00:01:29.9400] DOT11_DRV[0]: Stop Radio0
[*09/03/2023 00:01:29.9400] Stopped Radio 0
[*09/03/2023 00:01:29.9650] DOT11_DRV[0]: Start Radio0
[*09/03/2023 00:01:29.9720] DOT11_DRV[0]: set_channel Channel set to 1/20
[*09/03/2023 00:01:30.3820] Started Radio 0
[*09/03/2023 00:01:30.3820] DOT11_DRV[0]: set_channel Channel set to 1/20
[*09/03/2023 00:01:30.3880] wl: Busy
[*09/03/2023 00:01:32.0260] DOT11_DRV[0]: Stop Radio0
[*09/03/2023 00:01:32.0260] Stopped Radio 0
[*09/03/2023 00:01:32.0520] DOT11_DRV[0]: Start Radio0
[*09/03/2023 00:01:32.0580] DOT11_DRV[0]: set_channel Channel set to 1/20
[*09/03/2023 00:01:32.4620] Started Radio 0
[*09/03/2023 00:01:32.4620] DOT11_DRV[0]: set_channel Channel set to 1/20
[*09/03/2023 00:01:32.4690] wl: Busy
[*09/03/2023 00:01:32.7090] DOT11_DRV[0]: Stop Radio0
[*09/03/2023 00:01:32.7090] Stopped Radio 0
[*09/03/2023 00:01:32.7360] DOT11_DRV[0]: Start Radio0
[*09/03/2023 00:01:32.7420] DOT11_DRV[0]: set_channel Channel set to 1/20
[*09/03/2023 00:01:33.1480] Started Radio 0
[*09/03/2023 00:01:33.1480] DOT11_DRV[0]: set_channel Channel set to 1/20
[*09/03/2023 00:01:33.1550] wl: Busy
[*09/03/2023 00:01:35.1500] DOT11_DRV[0]: Stop Radio0
[*09/03/2023 00:01:35.1510] Stopped Radio 0
[*09/03/2023 00:01:35.1860] DOT11_DRV[0]: Start Radio0
[*09/03/2023 00:01:35.1930] DOT11_DRV[0]: set_channel Channel set to 1/20
[*09/03/2023 00:01:35.7270] Started Radio 0
[*09/03/2023 00:01:35.7270] DOT11_DRV[0]: set_channel Channel set to 1/20
[*09/03/2023 00:01:35.7350] wl: Busy
[*09/03/2023 00:01:36.9180] size: 17504 bytes (48032 left)
[*09/03/2023 00:01:37.1650] DOT11_DRV[1]: Stop Radio1
[*09/03/2023 00:01:37.1650] Stopped Radio 1
[*09/03/2023 00:01:37.1920] DOT11_DRV[1]: Start Radio1
[*09/03/2023 00:01:37.1980] DOT11_DRV[1]: set_channel Channel set to 36/20
[*09/03/2023 00:01:37.6070] Started Radio 1
[*09/03/2023 00:01:37.6070] DOT11_DRV[1]: set_channel Channel set to 36/20
[*09/03/2023 00:01:37.6500] wl: Unsupported
[*09/03/2023 00:01:39.3630] DOT11_DRV[1]: Stop Radio1
[*09/03/2023 00:01:39.3630] Stopped Radio 1
[*09/03/2023 00:01:39.3890] DOT11_DRV[1]: Start Radio1
[*09/03/2023 00:01:39.3960] DOT11_DRV[1]: set_channel Channel set to 36/20
[*09/03/2023 00:01:39.7960] Started Radio 1
[*09/03/2023 00:01:39.7960] DOT11_DRV[1]: set_channel Channel set to 36/20
[*09/03/2023 00:01:41.7760] DOT11_DRV[1]: Stop Radio1
[*09/03/2023 00:01:41.7760] Stopped Radio 1
[*09/03/2023 00:01:41.8010] DOT11_DRV[1]: Start Radio1
[*09/03/2023 00:01:41.8080] DOT11_DRV[1]: set_channel Channel set to 36/20
[*09/03/2023 00:01:42.2000] Started Radio 1
[*09/03/2023 00:01:42.2000] DOT11_DRV[1]: set_channel Channel set to 36/20
[*09/03/2023 00:01:44.1120] DOT11_DRV[1]: Stop Radio1
[*09/03/2023 00:01:44.1120] Stopped Radio 1
[*09/03/2023 00:01:44.1380] DOT11_DRV[1]: Start Radio1
[*09/03/2023 00:01:44.1450] DOT11_DRV[1]: set_channel Channel set to 36/20
[*09/03/2023 00:01:44.5410] Started Radio 1
[*09/03/2023 00:01:44.5410] DOT11_DRV[1]: set_channel Channel set to 36/20
[*09/03/2023 00:01:44.6930] DOT11_DRV[1]: Stop Radio1
[*09/03/2023 00:01:44.6930] Stopped Radio 1
[*09/03/2023 00:01:44.7230] DOT11_DRV[1]: Start Radio1
[*09/03/2023 00:01:44.7290] DOT11_DRV[1]: set_channel Channel set to 36/20
[*09/03/2023 00:01:45.1240] Started Radio 1
[*09/03/2023 00:01:45.1240] DOT11_DRV[1]: set_channel Channel set to 36/20
[*09/03/2023 00:01:45.8010] OK
[*09/03/2023 00:01:47.4330] DOT11_DRV[1]: Stop Radio1
[*09/03/2023 00:01:47.4330] Stopped Radio 1
[*09/03/2023 00:01:47.4570] DOT11_DRV[1]: Start Radio1
[*09/03/2023 00:01:47.4640] DOT11_DRV[1]: set_channel Channel set to 36/20
[*09/03/2023 00:01:47.9010] Started Radio 1
[*09/03/2023 00:01:47.9010] DOT11_DRV[1]: set_channel Channel set to 36/20
[*09/03/2023 00:01:47.9920] Socket: Valid Element: wcp/wcp_db Handler: set_vlan_name_map Data: null Length: 10
Stopping Cisco syslog service...
[ OK ] Stopped Cisco syslog service.
Starting Cisco syslog service...
[ OK ] Started Cisco syslog service.
[ OK ] Started ME Install Script.
[ OK ] Reached target Multi-User System.
[*09/03/2023 00:02:01.9770] chatter: tohost_virtual :: ToHost: device 'virtual' went down
Sun Sep 3 00:02:02 UTC 2023 SSun Sep 3 00:02:02 UTC 2023 Creating webauth tarball extract directory
Sun Sep 3 00:02:02 UTC 2023 IOSd monitor 9385 started
Sun Sep 3 00:02:02 UTC 2023 fromdev_wired0 count = 3
systemd 243 running in system mode. (+PAM +AUDIT +SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN2 -IDN -PCRE2 default-hierarchy=hybrid)
Detected virtualization container-other.
Detected architecture arm64.
Running with unpopulated /etc.
Initializing machine ID from random generator.
Populated /etc with preset unit settings.
/usr/lib/systemd/system/dbus.socket:5: ListenStream= references a path below legacy directory /var/run/, updating /var/run/dbus/system_bus_socket → /run/dbus/system_bus_socket; please update the unit file accordingly.
system-check_storage.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling.
(This warning is only shown for the first unit using IP firewalling.)

Both links down, not waiting for other chassis
Chassis number is 1

Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

Cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706

Cisco IOS Software [Bengaluru], C9800-AP Software (C9800-AP-K9_IOSXE-UNIVERSALK9-M), Version 17.6.4, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2022 by Cisco Systems, Inc.
Compiled Sun 14-Aug-22 06:34 by mcpre

This software version supports only Smart Licensing as the software licensing mechanism.

PLEASE READ THE FOLLOWING TERMS CAREFULLY. INSTALLING THE LICENSE OR
LICENSE KEY PROVIDED FOR ANY CISCO SOFTWARE PRODUCT, PRODUCT FEATURE,
AND/OR SUBSEQUENTLY PROVIDED SOFTWARE FEATURES (COLLECTIVELY, THE
"SOFTWARE"), AND/OR USING SUCH SOFTWARE CONSTITUTES YOUR FULL
ACCEPTANCE OF THE FOLLOWING TERMS. YOU MUST NOT PROCEED FURTHER IF YOU
ARE NOT WILLING TO BE BOUND BY ALL THE TERMS SET FORTH HEREIN.

Your use of the Software is subject to the Cisco End User License Agreement
(EULA) and any relevant supplemental terms (SEULA) found at
http://www.cisco.com/c/en/us/about/legal/cloud-and-software/software-terms.html.

You hereby acknowledge and agree that certain Software and/or features are
licensed for a particular term, that the license to such Software and/or
features is valid only for the applicable term and that such Software and/or
features may be shut down or otherwise terminated by Cisco after expiration
of the applicable license term (e.g., 90-day trial period). Cisco reserves
the right to terminate any such Software feature electronically or by any
other means available. While Cisco may provide alerts, it is your sole
responsibility to monitor your usage of any such term Software feature to
ensure that your systems and networks are prepared for a shutdown of the
Software feature.

FIPS: Flash Key Check : Key Not Found, FIPS Mode Not Enabled
platform init
All TCP AO KDF Tests Pass
cisco C9120AXE-B (VXE) processor (revision VXE) with 227901K bytes of memory.
Processor board ID FJC27291KND
2048K bytes of non-volatile configuration memory.
1875204K bytes of physical memory.
100000K bytes of AP Images at ap_images:.
513300K bytes of Backup Controller Image at backup_image:.
7774207K bytes of virtual hard disk at bootflash:.
25000K bytes of Temp trace export at tmp_trace_export:.
Installation mode is BUNDLE

%Default route without gateway, if not a point-to-point interface, may impact performance
Num of cpu cores 4
Maximum number of AP's supported 100
%Default route without gateway, if not a point-to-point interface, may impact performance
No such file

wenli · ‎09-27-2023

There isn't a Wireless LAN Controller (WLC) involved. I simply attempted a configuration change without altering the management IP address. The default IP address is 192.168.1.1, and after the reboot, the device was able to locate the controller.

marce1000 · ‎09-26-2023

- Make sure the AP gets sufficient power ; also post the complete boot process from the AP ,

M.

-- Each morning when I wake up and look into the mirror I always say ' Why am I so brilliant ? '
When the mirror will then always repond to me with ' The only thing that exceeds your brilliance is your beauty! '

wenli · ‎09-27-2023