Have a customer that we are going to be upgrading 8.5 to 8.10. In the process we are losing a bunch of AIR2602's and then adding new AIR9105's. Do we need to remove the 2602's before we upgrade and then once the upgrade is done, add all of the new ...
Forum Posts
Hola, hemos adquirido AP C9128AXE-E y antena AIR-ANT2513P4M-N para utilizarlo como radioenlaces. Pero, hasta ahora, ha sido imposible acceder a la configuración. Por lo que hemos leído por la web, necesitamos un equipo más, un WCL, el cual que no ten...
Hi Experts How do we shut no shut or bounce AP PoE ports from WLC. Basically we have cameras connected to the outdoor mesh and we want to bounce the ports so they can get new IPs from DHCP. Cheers!
MR42 and MR46 access points running firmware MR 30.7Authentication set to WPA3 authentication.We're seeing this about 1-2 times a day on a 65 device environment. The Mac will try to connect for 30+ seconds, then will show as connected, but with no in...
Hi there,We're using 2FA for our Authentication on Wireless which is from our Azure AD and sync on the Radius Server using Custom API.I know this is a known issue with CNA of Apple when the authentication is using 2FA.I have seen also some forum with...
I am having a strange problem with my AirOS 8540 WLC sometimes using the wrong DHCP proxy IP for one of my vlan interfaces.I have a ISE enabled SSID where i have set a dummy interface in the WLAN tab.Normaly this works flawless for all the networks.B...
Resolved! Hotel WiFi Deployment.
Good day,We've changed our Hotel Wifi APs to Cisco 9120-AX with Catalyst 9800 controller. We're running into an issue where through the hallway the signal is good, but several rooms on each floor have weak or inconsistent signal strength. The APs are...
I have an Organization with approximately (5)0 9163E access points deployed across 15 networks. Though 5GHz is enabled in the RF profile, all of them have no 5GHz working. In the AP detail, they all show power level -1 and channel 36. All are on v30....
Under Network-wide / Configure / Alerts / Alert Settings / Wireless, can anyone provide hard number definitions (or percentage values, if it's a ratio) for the dropdown values when making a Client Bandwidth Usage Alert?
Resolved! Cisco WLC 9800 AP Groups
Hi All, How are you using AP Groups on the Cisco 9800 WLC setup? on Aireos (the 8500 WLC in this case) we had multiple AP groups used at a site to define the settings for a selection of AP's for different area's of that site e.g. office, manufacturin...
Resolved! Error conflict DHCP
How might I have received this error in some APs?I have the DHCP in another Fw that I changed recently.How it is possibel i recived this error this DHCP it is only for meraki AP I put a fix IP on the FW for this AP i rebooting the AP, I experienced t...
I was recently advised to set 24Mbps as the minimum mandatory data rate and 18Mbps as supported. I'm wondering if having one supported data rate below the minimum mandatory data rate is considered best practice. I had been under the impression that t...
Hi ,Last week on 3 different networks I had 20+ APs that were down. The switchport had the error : SecurePort authentication failureAfter taking packet captures , I noticed that the certificate of the APs were expired : I had to reboot the APs like 1...
I have two new 9800-40 controllers running 17.06.03One chassis set to to number 1 priority 2 and the other is number 2 priority 1.When they are booted at the same time, eventually dual-active recovery is triggered and one chassis goes to active recov...
Can the IP address of an AP be associated to a different VLAN than the Native VLAN
