02-04-2015 11:38 AM - edited 07-05-2021 02:26 AM
dear all,
i just install Virtual WLC and i remove WLC 2504 , i install & configured it , but LAP can not join. it was work fine with WLC 2504.
i used the same network topology with the old WLC.
i receive this error logs.
*spamApTask4: Feb 04 06:01:30.082: <<<< Start of CAPWAP Packet >>>>
*spamApTask4: Feb 04 06:01:30.082: CAPWAP Control mesg Recd from 10.192.200.93, Port 26711
*spamApTask4: Feb 04 06:01:30.082: HLEN 4, Radio ID 0, WBID 1
*spamApTask4: Feb 04 06:01:30.082: Msg Type : CAPWAP_DISCOVERY_REQUEST
*spamApTask4: Feb 04 06:01:30.082: Msg Length : 155
*spamApTask4: Feb 04 06:01:30.082: Msg SeqNum : 0
*spamApTask4: Feb 04 06:01:30.082:
*spamApTask4: Feb 04 06:01:30.082: Type : CAPWAP_MSGELE_DISCOVERY_TYPE, Length 1
*spamApTask4: Feb 04 06:01:30.082: Discovery Type : CAPWAP_DISCOVERY_TYPE_UNKNOWN
*spamApTask4: Feb 04 06:01:30.082:
*spamApTask4: Feb 04 06:01:30.082: Type : CAPWAP_MSGELE_WTP_BOARD_DATA, Length 62
*spamApTask4: Feb 04 06:01:30.083: Vendor Identifier : 0x00409600
*spamApTask4: Feb 04 06:01:30.083: WTP_SERIAL_NUMBER : AIR-CAP2602E-I-K9
*spamApTask4: Feb 04 06:01:30.083:
*spamApTask4: Feb 04 06:01:30.083: Type : CAPWAP_MSGELE_WTP_DESCRIPTOR, Length 40
*spamApTask4: Feb 04 06:01:30.083: Maximum Radios Supported : 2
*spamApTask4: Feb 04 06:01:30.083: Radios in Use : 2
*spamApTask4: Feb 04 06:01:30.083: Encryption Capabilities : 0x00 0x01
*spamApTask4: Feb 04 06:01:30.083:
*spamApTask4: Feb 04 06:01:30.083: Type : CAPWAP_MSGELE_WTP_FRAME_TUNNEL, Length 1
*spamApTask4: Feb 04 06:01:30.083: WTP Frame Tunnel Mode : NATIVE_FRAME_TUNNEL_MODE
*spamApTask4: Feb 04 06:01:30.083:
*spamApTask4: Feb 04 06:01:30.083: Type : CAPWAP_MSGELE_WTP_MAC_TYPE, Length 1
*spamApTask4: Feb 04 06:01:30.083: WTP Mac Type : SPLIT_MAC
*spamApTask4: Feb 04 06:01:30.083:
*spamApTask4: Feb 04 06:01:30.083: Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 10
*spamApTask4: Feb 04 06:01:30.083: Vendor Identifier : 0x00409600
*spamApTask4: Feb 04 06:01:30.083:
IE : UNKNOWN IE 207
*spamApTask4: Feb 04 06:01:30.083: IE Length : 4
*spamApTask4: Feb 04 06:01:30.083: Decode routine not available, Printing Hex Dump
*spamApTask4: Feb 04 06:01:30.083: 00000000: 03 00 00 01 ....
*spamApTask4: Feb 04 06:01:30.083:
*spamApTask4: Feb 04 06:01:30.083: Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 12
*spamApTask4: Feb 04 06:01:30.083: Vendor Identifier : 0x00409600
*spamApTask4: Feb 04 06:01:30.083:
IE : RAD_NAME_PAYLOAD
*spamApTask4: Feb 04 06:01:30.083: IE Length : 6
*spamApTask4: Feb 04 06:01:30.083: Rad Name :
*spamApTask4: Feb 04 06:01:30.083: CEO_AP
*spamApTask4: Feb 04 06:01:30.083: <<<< End of CAPWAP Packet >>>>
*spamApTask4: Feb 04 06:01:30.083: dc:a5:f4:8c:ff:30 Discovery Request from 10.192.200.93:26711
*spamApTask4: Feb 04 06:01:30.083: dc:a5:f4:8c:ff:30 ApModel: AIR-CAP2602E-I-K9
*spamApTask4: Feb 04 06:01:30.083: dc:a5:f4:8c:ff:30 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 200, joined Aps =0
*spamApTask4: Feb 04 06:01:30.083: apModel: AIR-CAP2602E-I-K9
*spamApTask4: Feb 04 06:01:30.083: apType = 26 apModel: AIR-CAP2602E-I-K9
*spamApTask4: Feb 04 06:01:30.083: apType: Ox1a bundleApImageVer: 8.0.110.0
*spamApTask4: Feb 04 06:01:30.083: version:8 release:0 maint:110 build:0
*spamApTask4: Feb 04 06:01:30.083: dc:a5:f4:8c:ff:30 Discovery Response sent to 10.192.200.93 port 26711
*spamApTask4: Feb 04 06:01:30.083: dc:a5:f4:8c:ff:30 Discovery Response sent to 10.192.200.93:26711
Please any help.
Solved! Go to Solution.
02-04-2015 12:04 PM
You may need to put the AP in flexconnect mode before you move it. Is the WLC 2504 at least 7.4?
02-04-2015 11:43 AM
Is the AP in flexconnect mode? Does the AP have at least version 7.4 on it? These are requirements.
02-04-2015 12:01 PM
Dear shh5455
in local mode because they was connected to wlc 2504, but if they joint i will change them to Flecconnect mode.
the vWLC is v 8.0.110
02-04-2015 12:04 PM
You may need to put the AP in flexconnect mode before you move it. Is the WLC 2504 at least 7.4?
02-04-2015 12:12 PM
dear
yes the wlc 2504 is 8.0.110 but because its damaged i replaced it with new vWLC v 8.0.110.
also i can not put the LAP in flexconnect until its joint.
02-04-2015 12:20 PM
Can you pull the logs off of the AP when it's trying to join?
02-05-2015 01:21 AM
Thank you dear
its joint now.
i just add command in the cWLC for flexconnect
BR
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide