- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-06-2014 04:56 AM - edited 07-05-2021 01:39 AM
Hi,
I have new Cisco AIR-CAP2602i-E-K9 and I try to configure it via CLI.
I log in, give username and password (defaults) and I'm in User EXEC mode.
Then I type enable and give password to get Privileged EXEC. At least command prompt changed to # and more commads are available.
Then I try to give 'configure' command to get next, Global configuration mode.
Problem: there is no 'configure' named command.
What to do? How to get further?
Best regards,
Hannu
Solved! Go to Solution.
- Labels:
-
Other Wireless Topics
Accepted Solutions
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-06-2014 11:17 AM
Hi.
If you need to configure something on this AP in CAPWAP mode by CLI, you should write:
"debug capwap console cli" In other case as Mohanak told you you need to convert your AP to Autnomous mode.
**Please rate useful answers**
**Please rate the answer if this information was useful***
**Por favor si la información fue util marca esta respuesta como correcta**
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-07-2014 08:33 AM
My pleasure :)
**Please rate the answer if this information was useful***
**Por favor si la información fue util marca esta respuesta como correcta**
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-06-2014 06:13 AM
Put ? symbol in # prompt and it will show u possible commands,here u can look for configuration related command.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-06-2014 06:27 AM
Problem is, that when I go to Privileged EXEC mode, there is NOT 'configure' command.

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-06-2014 07:32 AM
Convert the AP to Autonomous and TRY:
https://supportforums.cisco.com/discussion/11833271/global-configuration-mode-aironet-2600i
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-06-2014 10:44 AM
Sounds and looks difficult. Is this the ONLY way?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-06-2014 11:17 AM
Hi.
If you need to configure something on this AP in CAPWAP mode by CLI, you should write:
"debug capwap console cli" In other case as Mohanak told you you need to convert your AP to Autnomous mode.
**Please rate useful answers**
**Please rate the answer if this information was useful***
**Por favor si la información fue util marca esta respuesta como correcta**
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-06-2014 11:23 PM
That works!
Thanks!
Hannu
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-07-2014 08:33 AM
My pleasure :)
**Please rate the answer if this information was useful***
**Por favor si la información fue util marca esta respuesta como correcta**
