cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
5621
Views
0
Helpful
3
Replies

How to stop a LAP from rebooting

dbauman_wan
Beginner
Beginner

I have a C1310 LAP that I need to downgrade to Autonomous, but it constantly reboots.

Is there anyway to stop this so I can get into it and load a full ios code?

*Mar  1 00:00:24.599: %LWAPP-3-CLIENTERRORLOG: LWAPP Crypto Init: could not start PKI session

*Mar  1 00:00:24.599: %LWAPP-3-CLIENTERRORLOG: Failed to initialize Crypto. Rebooting

*Mar  1 00:00:24.625: %SYS-4-PUPDATECLOCK: Periodic Clock update with ROMMON failed, because size left in ROMMON (4294967295), size needed (29), error code (-1)

*Mar  1 00:00:24.625: %SYS-5-RELOAD: Reload requested by CAPWAP CLIENT. Reload Reason: FAILED CRYPTO INIT.

*Mar  1 00:00:24.626: %LWAPP-5-CHANGED: CAPWAP changed state to DOWN

Thanks,

David    

1 Accepted Solution

Accepted Solutions

Stephen Rodriguez
Cisco Employee
Cisco Employee

Debug capwap con CLI

Debug LWAPP client no-reload <- If I recall correctly

Steve

Sent from Cisco Technical Support iPhone App

HTH,
Steve

------------------------------------------------------------------------------------------------
Please remember to rate useful posts, and mark questions as answered

View solution in original post

3 Replies 3

Stephen Rodriguez
Cisco Employee
Cisco Employee

Debug capwap con CLI

Debug LWAPP client no-reload <- If I recall correctly

Steve

Sent from Cisco Technical Support iPhone App

HTH,
Steve

------------------------------------------------------------------------------------------------
Please remember to rate useful posts, and mark questions as answered

Looks promising, but still rebooting:

Press RETURN to get started!

*Mar  1 00:00:04.711: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 100 messages)

*Mar  1 00:00:06.716: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up

*Mar  1 00:00:06.743: %SYS-5-RESTART: System restarted --

Cisco IOS Software, C1310 Software (C1310-RCVK9W8-M), Version 12.4(21a)JA2, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2009 by Cisco Systems, Inc.

Compiled Mon 02-Nov-09 18:12 by prod_rel_team

*Mar  1 0

AP000f.90f9.b79c>0:00:06.771: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY

*Mar  1 00:00:06.808: %LWAPP-3-CLIENTERRORLOG: LWAPP Crypto Init (SSC): no certs in the SSC Private File

*Mar  1 00:00:07.716: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to upen

Password:

AP000f.90f9.b79c#Debug capwap con CLI

This command is meant only for debugging/troubleshooting

Any configuration change may result in different

behavior from centralized configuration.

CAPWAP console CLI allow/disallow debugging is on

AP000f.90f9.b79c#Debug LWAPP client  no-reload

LWAPP ignore internal reload debugging is on

*Mar  1 00:00:15.936: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 172.16.1.107, mask 255.255.255.0, hostname AP000f.90f9.b79c

Writing out the event log to nvram...

*Mar  1 00:00:25.718: %LWAPP-3-CLIENTERRORLOG: LWAPP Crypto Init: could not start PKI session

*Mar  1 00:00:25.718: %LWAPP-3-CLIENTERRORLOG: Failed to initialize Crypto. Rebooting

*Mar  1 00:00:25.734: %SYS-4-PUPDATECLOCK: Periodic Clock update with ROMMON failed, because size left in ROMMON (4294967295), size needed (29), error code (-1)

*Mar  1 00:00:25.734: %SYS-5-RELOAD: Reload requested by CAPWAP CLIENT. Reload Reason: FAILED CRYPTO INIT.

*Mar  1 00:00:25.735: %LWAPP-5-CHANGED: CAPWAP changed state to DOWN

AP000f.90f9.b79c#

Along with this: 

debug capwap cli no-reload

It worked.

Thanks!David

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: