Buy or Renew
Buy or Renew
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
967
Views
0
Helpful
4
Replies

Issue with Gui Aironet 2702i

Go to solution
tomnick
Level 1
Level 1

‎11-02-2022 10:14 AM

Hi, I bought a used AIR-CAP2702I-E-K9 with ap3g2-k9w7-xx.153-3.JPJ2 installed. I am trying to set up the network interface settings for a repeater but it only shows me a very short version of it and not the long one. What have I done wrong? Thanks for a little hint....

 

Labels:
0 Helpful
2 Accepted Solutions

Accepted Solutions

Go to solution
Rich R
VIP
VIP

‎11-03-2022 07:04 PM

Yes stick to using the CLI to configure those autonomous APs.

There are a number of bugs in the GUI which will not be fixed so if it works great, if it doesn't use the CLI.

You could also try older versions of software if you insist on using the GUI and then upgrade once you have a working config.

------------------------------
Please click Helpful if this post helped you and Select as Solution (drop down menu at top right of this reply) if this answered your query.
------------------------------
TAC recommended codes for AireOS WLC's   and   TAC recommended codes for 9800 WLC's
Best Practices for AireOS WLC's,   Best Practices for 9800 WLC's   and   Cisco Wireless compatibility matrix
Check your 9800 WLC config with Wireless Config Analyzer using "show tech wireless" output or "config paging disable" then "show run-config" output on AireOS and use Wireless Debug Analyzer to analyze your WLC client debugs
Field Notice: FN63942 APs and WLCs Fail to Create CAPWAP Connections Due to Certificate Expiration
Field Notice: FN72424 Later Versions of WiFi 6 APs Fail to Join WLC - Software Upgrade Required
Field Notice: FN72524 IOS APs stuck in downloading state after 4 Dec 2022 due to Certificate Expired
- Fixed in 8.10.196.0, latest 9800 releases, 8.5.182.12 (8.5.182.13 for 3504) and 8.5.182.109 (IRCM, 8.5.182.111 for 3504)
Field Notice: FN70479 AP Fails to Join or Joins with 1 Radio due to Country Mismatch, RMA needed
How to avoid boot loop due to corrupted image on Wave 2 and Catalyst 11ax Access Points (CSCvx32806)
Field Notice: FN74035 - Wave2 APs DFS May Not Detect Radar After Channel Availability Check Time
Leo's list of bugs affecting 2800/3800/4800/1560 APs
Default AP console baud rate from 17.12.x is 115200 - introduced by CSCwe88390

View solution in original post

0 Helpful
4 Replies 4

Go to solution
marce1000
Hall of Fame
Hall of Fame

‎11-02-2022 10:56 AM

 

                   - Can you post a screenshot ?

 M.



-- Each morning when I wake up and look into the mirror I always say ' Why am I so brilliant ? '
    When the mirror will then always repond to me with ' The only thing that exceeds your brilliance is your beauty! '
0 Helpful

Go to solution
tomnick
Level 1
Level 1
In response to marce1000

‎11-03-2022 12:39 AM

Bildschirmfoto von 2022-11-03 08-37-46.png

0 Helpful

Go to solution
Rich R
VIP
VIP

‎11-03-2022 07:04 PM

Yes stick to using the CLI to configure those autonomous APs.

There are a number of bugs in the GUI which will not be fixed so if it works great, if it doesn't use the CLI.

You could also try older versions of software if you insist on using the GUI and then upgrade once you have a working config.

------------------------------
Please click Helpful if this post helped you and Select as Solution (drop down menu at top right of this reply) if this answered your query.
------------------------------
TAC recommended codes for AireOS WLC's   and   TAC recommended codes for 9800 WLC's
Best Practices for AireOS WLC's,   Best Practices for 9800 WLC's   and   Cisco Wireless compatibility matrix
Check your 9800 WLC config with Wireless Config Analyzer using "show tech wireless" output or "config paging disable" then "show run-config" output on AireOS and use Wireless Debug Analyzer to analyze your WLC client debugs
Field Notice: FN63942 APs and WLCs Fail to Create CAPWAP Connections Due to Certificate Expiration
Field Notice: FN72424 Later Versions of WiFi 6 APs Fail to Join WLC - Software Upgrade Required
Field Notice: FN72524 IOS APs stuck in downloading state after 4 Dec 2022 due to Certificate Expired
- Fixed in 8.10.196.0, latest 9800 releases, 8.5.182.12 (8.5.182.13 for 3504) and 8.5.182.109 (IRCM, 8.5.182.111 for 3504)
Field Notice: FN70479 AP Fails to Join or Joins with 1 Radio due to Country Mismatch, RMA needed
How to avoid boot loop due to corrupted image on Wave 2 and Catalyst 11ax Access Points (CSCvx32806)
Field Notice: FN74035 - Wave2 APs DFS May Not Detect Radar After Channel Availability Check Time
Leo's list of bugs affecting 2800/3800/4800/1560 APs
Default AP console baud rate from 17.12.x is 115200 - introduced by CSCwe88390
0 Helpful
Customers Also Viewed These Support Documents
Review Cisco Networking for a $25 gift card