12-10-2010 09:01 PM - edited 07-03-2021 07:32 PM
My config is an autonomous 1124N running 12.4 configured by CLI. Attached is the config I've built so far.
Due to the fact that this AP did not ship with a power adaptor and I have no power injector and that the only power I have is from a ASA 5505 that I do not want to reconfigure presently, I cannot run the gui, hence the CLI is my only option.
Can anyone please tell me why radio 1 will not start?
Thanks in advance
Solved! Go to Solution.
12-10-2010 09:57 PM
Hi,
Can you add subinterfaces for radio1, just in the same way that you have for radio 0 :
interface Dot11Radio1.10
encapsulation dot1Q 10 native
bridge-group 1
interface Dot11Radio1.20
encapsulation dot1Q 20
bridge-group 20
interface Dot11Radio1.30
encapsulation dot1Q 30
bridge-group 30
Regards,
Madhuri
12-10-2010 10:57 PM
Looks like he already has the vlan mapped to ssid from
the attached file
!
dot11 ssid 4-C
vlan 20
authentication open
!
dot11 ssid 4-C_Public
vlan 30
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii 7 104D0D1C5142440808017E
!
encryption vlan 30 mode ciphers aes-ccm tkip
!
encryption vlan 20 mode ciphers aes-ccm tkip
12-10-2010 09:33 PM
This is the message I get, but as far as I can tell, I've met this requirement.
%DOT11-4-NO_SSID_OR_NO_VLAN: No SSID configured. Dot11Radio1 not started.
12-10-2010 09:57 PM
Hi,
Can you add subinterfaces for radio1, just in the same way that you have for radio 0 :
interface Dot11Radio1.10
encapsulation dot1Q 10 native
bridge-group 1
interface Dot11Radio1.20
encapsulation dot1Q 20
bridge-group 20
interface Dot11Radio1.30
encapsulation dot1Q 30
bridge-group 30
Regards,
Madhuri
12-11-2010 04:46 AM
Nice catch--Thanks!
Guess I've been looking at too many screens lately (I thought I had dot11radio1 subinterfaces in my config build file).
12-11-2010 07:17 AM
oops i missed it.. i gues Madhuri answered your question and resolved the issue.. 5 for her!!.. and also if you are facing any issue please open up a new discussion rather posting on the answered posts.. More people respond to the new posts..
Regards
Surendra
12-10-2010 10:41 PM
The error msg is telling that there is SSID or VLAN mapped to DOT11 RADIO 1..
So either of the below will solve..
en
conf t
dot11 ssid
vlan X
end
int dot11 1
ssid
encryption vlan <#>
end
This will solve the issue..
Regards
Surendra
12-10-2010 10:57 PM
Looks like he already has the vlan mapped to ssid from
the attached file
!
dot11 ssid 4-C
vlan 20
authentication open
!
dot11 ssid 4-C_Public
vlan 30
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii 7 104D0D1C5142440808017E
!
encryption vlan 30 mode ciphers aes-ccm tkip
!
encryption vlan 20 mode ciphers aes-ccm tkip
12-11-2010 04:49 AM
Thanks to all who responded!
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide