ā10-08-2012 09:03 AM - edited ā07-03-2021 10:47 PM
Hi,
I have an interesting job where i am having to fit a wifi network through a large property. I was advised to use the Cisco 2504 WLC and 9 x Cisco AIR-AP1142N access points.
I know that out of the box the AP's (in standalone versions) have the GUI enabled.
Not being completley up with CLI etc, is the WLC GUI enabled straight out of the box? if not, is it complicated to get it up and running? I'm pretty good at learning/understanding these things just as long as i have a rough idea of what to do!
Thanks in advance,
Josh
ā10-08-2012 09:06 AM
By default you need to connect to the console port, and run through the configuration wizard there first. But once that is done, only takes a few mintues, you have access to the GUI
HTH,
Steve
------------------------------------------------------------------------------------------------
Please remember to rate useful posts, and mark questions as answered
ā10-08-2012 09:08 AM
Keep in mind when ordering access point you can purchase them in capwap or autonomous.
Sent from Cisco Technical Support iPhone App
ā10-08-2012 10:17 AM
Thanks for your amazingly fast responses!
This is the product code i was planning on ordering....
AIR-LAP1142N-E-K9 should i infact order
AIR-LAP1142N-S-K9?
Bear in mind this is for a UK deployment.
Thanks,
Josh
ā10-08-2012 10:33 AM
For UK, you should order
AIR-LAP1142N-E-K9
HTH,
Steve
------------------------------------------------------------------------------------------------
Please remember to rate useful posts, and mark questions as answered
ā10-08-2012 10:35 AM
Thats what i was thinking
But, does that mean it's capwap or autonomous as the previous comment suggested.... or is that irrelvant?
This is the first one of these installs ive done so it's all a bit new!
ā10-08-2012 10:39 AM
For the most part it is irrelevant. You can convert the AP between CAPWAP and IOS easily enough.
But if you are planning on using a WLC, I would order the LAP version and have it be CAPWAP by default.
HTH,
Steve
------------------------------------------------------------------------------------------------
Please remember to rate useful posts, and mark questions as answered
ā10-13-2012 06:51 AM
Thats great, Thanks steve.
I have the Controller (although AP's are still on order - out of stock ) but i have one final question before i start to set it up!
I'm looking at this guide: http://www.cisco.com/en/US/docs/wireless/controller/2500/quick/guide/ctr2504_q_s.html#wp34023 and it talks about Management interface. I presume the management IP address would be the fixed ip of the controller if you like.
So if i had a network with a DHCP server. The Router/Server was 192.168.2.1 and the DHCP range started from .10, i could set this to be 192.168.2.2 with the router of the management interface to be .2.1. I then could set the VLAN id to be 0 as i don't need a seperate managment lan (it's only for a house afterall, and if i lock it down with passwords it should be fine).
With the Management Port, i presume that can be the port that connects into the main PoE Switch, similalry the Management DHCP server would be 192.168.2.1?
Virtual Gateway IP address i guess is irelevant as there will be no mobility group?
And DHCP bridging, like on any other wifi system/AP would be 'No' as the Router will be dealing with all DHCP requests?
Thanks again for your fantastic help so far!
Josh
ā10-13-2012 09:58 AM
Hi,
LAP in the part number stands for lighweight AP.
AP stands for Autonomous.
management port can be set at your preference, with a backup port.
Virtual IP is also for WebAuth with DNS gateway reservation, VPN termination, and is used on the DHCP process
how about you try this document
ā10-13-2012 07:03 AM
Just to help out Steve:)
Yes you can set the management to 2.2 as long as no other device is using this address. If the wireless users will be placed on a different vlan, then make sure the on the switch, you only allow the vlans that you have defined on the WLC. So that would be the management vlan and any dynamic interfaces vlans you configure on the WLC. If you are not doing QoS, then you can leave the management interface tagged as 0. If you want to use QoS then tag the management interface. When you don't tag the interface, you need to specify the native vlan on the trunk ports.
You need to define the VIP so make sure it's non routable in your network.... This is mandatory.
Sent from Cisco Technical Support iPhone App
ā10-13-2012 08:58 AM
Hi Scott,
Thanks for this. Again the support provided on here makes choosing Cisco a great decision! However, just a little question, the VIP... is this required even to get the GUI active? Thats all i'm really after doing. Programming it through CLI until i can get on the admin interface to programm it on GUI.
On the link i listed above there is nothing listed about VIP?
Thanks,
Josh
ā10-13-2012 09:02 AM
You mentioned the following
Virtual Gateway IP address i guess is irelevant as there will be no mobility group?
When you go throught the startup wizard, you will need to dfine the VIP address which is required. So just choose any non routable ip address for this.
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"
ā10-13-2012 09:05 AM
For example 10.10.10.1?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide