04-05-2012 10:28 AM - edited 07-03-2021 09:57 PM
Hello, does anybody know how to enable wireless N speeds on this access point? It's operating in mixed mode via PoE. If I go into network interfaces -> Radio0-802.11N --> Settings, the highest data rate is only 54 mbps. Can N speeds be acheived in mix mode? Also, I thought this access point is dual-band, but I'm only seeing the one radio, is that normal? (see attached image)
Thanks in advance.
Solved! Go to Solution.
04-05-2012 10:32 AM
Hi Jason,
You see the MCS rates, thats your 802.11n
Also, keep in mind you need to allow WMM.
And you need to either have a OPEN unsecure network or use WPA2/AES to do 802.11n RATEs
Modulation Coding Scheme (MCS) Index | Number of spatial streams | Modulation used | Data Rate when GI=800ns | Data Rate when GI=400ns |
0 | 1 | BPSK | 13.5 | 15 |
1 | 1 | QPSK | 27 | 30 |
2 | 1 | QPSK | 40.5 | 45 |
3 | 1 | 16-QAM | 54 | 60 |
4 | 1 | 16-QAM | 81 | 90 |
5 | 1 | 64-QAM | 108 | 120 |
6 | 1 | 64-QAM | 121.5 | 135 |
7 | 1 | 64-QAM | 135 | 157.5 |
8 | 2 | BPSK | 27 | 30 |
9 | 2 | QPSK | 54 | 60 |
10 | 2 | QPSK | 81 | 90 |
11 | 2 | 16-QAM | 108 | 120 |
12 | 2 | 16-QAM | 162 | 180 |
13 | 2 | 64-QAM | 216 | 240 |
14 | 2 | 64-QAM | 243 | 270 |
15 | 2 | 64-QAM | 270 | 300 |
04-05-2012 11:25 AM
Post your show run config .. Lets take a peek
QoS / WMM needs to be enabled and WPA2/AES ..
04-05-2012 10:32 AM
Hi Jason,
You see the MCS rates, thats your 802.11n
Also, keep in mind you need to allow WMM.
And you need to either have a OPEN unsecure network or use WPA2/AES to do 802.11n RATEs
Modulation Coding Scheme (MCS) Index | Number of spatial streams | Modulation used | Data Rate when GI=800ns | Data Rate when GI=400ns |
0 | 1 | BPSK | 13.5 | 15 |
1 | 1 | QPSK | 27 | 30 |
2 | 1 | QPSK | 40.5 | 45 |
3 | 1 | 16-QAM | 54 | 60 |
4 | 1 | 16-QAM | 81 | 90 |
5 | 1 | 64-QAM | 108 | 120 |
6 | 1 | 64-QAM | 121.5 | 135 |
7 | 1 | 64-QAM | 135 | 157.5 |
8 | 2 | BPSK | 27 | 30 |
9 | 2 | QPSK | 54 | 60 |
10 | 2 | QPSK | 81 | 90 |
11 | 2 | 16-QAM | 108 | 120 |
12 | 2 | 16-QAM | 162 | 180 |
13 | 2 | 64-QAM | 216 | 240 |
14 | 2 | 64-QAM | 243 | 270 |
15 | 2 | 64-QAM | 270 | 300 |
04-05-2012 11:23 AM
Thanks for the quick replies everyone. Ok, I see the MCS rate table now. By WMM do you mean "World Mode Multi-Domain Operation"? It was disabled, but I enabled it at Dot11d and specified US country code, but still only connect at 54Mbps. I'm using WPA2-enterprise security, so that should work right? Anything else I can check?
04-05-2012 11:25 AM
Post your show run config .. Lets take a peek
QoS / WMM needs to be enabled and WPA2/AES ..
04-05-2012 11:31 AM
BTW what client are you using to determine you arent getting 802.11n speeds?
04-05-2012 11:40 AM
04-05-2012 10:34 AM
04-05-2012 10:37 AM
To add to Rons point, you will not be able to bond on 2.4 so at best you will get 144
04-05-2012 11:44 AM
Switching to AES got me up to 144 Mbps, which is the max according you, so I'll take it! Thanks so much for you help everyone!
04-05-2012 11:53 AM
LOL, accroding to me! I like the tone to that !
Yes, if you get a 1042 with a a/n radio you can bond and you will get 300.
Cool ... Enjoy!
Thanks for supporting the rating system ..
06-24-2016 12:19 PM
My cisco function only 54mb, how to configure 150mb or 300mb?
06-24-2016 12:18 PM
My cisco function only 54mb, how to configure 150mb or 300mb?
06-24-2016 12:23 PM
My cisco function only 54mb, how to configure 150mb or 300mb?
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: