WLC Config Analyzer - CDH Per WLAN

[melcara]

Just curious, when using the WLC Config Analyzer, one of the report items says "CDH Per WLAN" either enabled or disabled, what is is this?

Thanks

[Scott Fella]

Do you mean CHD (coverage hole detection)?

Sent from Cisco Technical Support iPhone App

[melcara]

I was thinking that also, but the tool gave that format

here is the output from the tool

Features per   Controller
Feature Name	Controller Name	Feature Version	Enabled
Load Based Call Admision Control	WLC_NAME	4.1	FALSE
FIPS 140-2	WLC_NAME	4.1	FALSE
Expedited Bandwith Request	WLC_NAME	4.1	FALSE
MFP Infraestructure	WLC_NAME	4.1	FALSE
Local EAP	WLC_NAME	4.1	FALSE
DCA Update Interval	WLC_NAME	4.1	FALSE
Tacacs	WLC_NAME	4.1	FALSE
Multiple Country	WLC_NAME	4.1	FALSE
1250 AP Support	WLC_NAME	4.2	FALSE
Wired Guest	WLC_NAME	4.2	FALSE
16 SSID per AP	WLC_NAME	4.2	FALSE
Syslog messages on APs	WLC_NAME	4.2	FALSE
Backup WLC AP enhancement	WLC_NAME	4.2	FALSE
H-REAP Backup Radius server support	WLC_NAME	4.2	FALSE
PEAP on Local EAP	WLC_NAME	4.2	FALSE
IPv6 bridged until webauth	WLC_NAME	4.2	FALSE
Enhanced control on MAC for voice	WLC_NAME	4.2	FALSE
EDCA parameters	WLC_NAME	4.2	TRUE
WMM settings for mixed enviroments	WLC_NAME	4.2	FALSE
Multicast IGMP	WLC_NAME	4.2	FALSE
Multicast Multicast mode Forwarding	WLC_NAME	4.2	FALSE
Peer to Peer Blocking per WLAN	WLC_NAME	4.2	FALSE
AP Telnet	WLC_NAME	5	FALSE
AP SSH	WLC_NAME	5	FALSE
DTIM Per WLAN	WLC_NAME	5	FALSE
AP Sniffer mode sent to Wireshark	WLC_NAME	5	FALSE
Increased Mobility Group for roaming up   to 48 controllers	WLC_NAME	5	FALSE
RRM Support for 40 MHz	WLC_NAME	5.1	FALSE
Increased Mobility Group for roaming up   to 72 controllers	WLC_NAME	5	FALSE
2100 Multicast Enhancements	WLC_NAME	5.1	FALSE
AP dot1x supplicant	WLC_NAME	5.1	FALSE
AP1140 Support	WLC_NAME	5.2	TRUE
CDH Per WLAN	WLC_NAME	5.2	TRUE
AP Locally significant Certificate	WLC_NAME	5.2	FALSE
Mesh Support	WLC_NAME	5.2	FALSE
Voice over Mesh Indoor	WLC_NAME	5.2	FALSE
More than 16 WLANs	WLC_NAME	5.2	FALSE
Up to 100 local users on H-REAP	WLC_NAME	5.2	FALSE
Do not learn Address for H-REAP client	WLC_NAME	5.2	FALSE

I just don't know if that is a type'o in the tool or not.

[Scott Fella · Accepted solution]

Must be a typo:). Disable CHD and see if it changes.

Thanks,

Scott Fella

Sent from my iPhone

[melcara]

That was definitly the setting, I guess the wireless team need to update the tool.

[Scott Fella]

They will notice your post. I guess just wait for the next version or you might be able to reply on the wlc config download page.

Thanks,

Scott Fella

Sent from my iPhone

[Javier Contreras]

Hi

yes, it is a typo...  I just fixed it, it will be solved on next WLCCA release, hopefully this week.

For any bug reports or feedback (new features, etc), please feel free to write to wlc-conf-app-dev@cisco.com

Regards!