Re: WMIC 3201 shut down its wireless in -20℃

QingwYang82917 · ‎01-27-2021

Hello,

I found WMIC 3201 shut down its wireless in -20℃ (environment temperature), and its internal temperature is at -2℃. I need to modify the configuration to let it work in at least -30℃, but I don't know how to do. Please give me some suggestions! Thanks!

Best wishes,

Yang

marce1000 · ‎01-27-2021

- Software configurations won't be able to battle device temperature operating capabilities which you may find in the datasheet for the particular device, you may need other hardware for this environment which can comply with temperatures experienced.

M.

-- Each morning when I wake up and look into the mirror I always say ' Why am I so brilliant ? '
When the mirror will then always repond to me with ' The only thing that exceeds your brilliance is your beauty! '

QingwYang82917 · ‎01-28-2021

-Thanks for your reply! And could you please tell me why WMIC 3201 set this minimum temperature to be -20℃? Its working temperature range could be -40~70℃ in the datasheet, and there is a temperature difference between them. Thanks again!

Best wishes,

Yang

marce1000 · ‎01-28-2021

- One thing you may want to try is to use the latest software version for the device, doubt this will help though. If the device does not operate according to temperature values mentioned in the datasheet you need to report this to Cisco and ask for explanations.

M.

-- Each morning when I wake up and look into the mirror I always say ' Why am I so brilliant ? '
When the mirror will then always repond to me with ' The only thing that exceeds your brilliance is your beauty! '

Rich R · ‎01-28-2021

It looks like this product went last date of support in 2015 so no chance of Cisco supporting it anymore:
https://teamkci.com/wp-content/uploads/C3270.pdf and I couldn't find a data sheet for it.

If you can't make this work by trial and error you'll have to look for a newer product.

------------------------------
Please click Helpful if this post helped you and Select as Solution (drop down menu at top right of this reply) if this answered your query.
------------------------------
TAC recommended codes for AireOS WLC's and TAC recommended codes for 9800 WLC's
Best Practices for AireOS WLC's, Best Practices for 9800 WLC's and Cisco Wireless compatibility matrix
Check your 9800 WLC config with Wireless Config Analyzer using "show tech wireless" output or "config paging disable" then "show run-config" output on AireOS and use Wireless Debug Analyzer to analyze your WLC client debugs
Field Notice: FN63942 APs and WLCs Fail to Create CAPWAP Connections Due to Certificate Expiration
Field Notice: FN72424 Later Versions of WiFi 6 APs Fail to Join WLC - Software Upgrade Required
Field Notice: FN72524 IOS APs stuck in downloading state after 4 Dec 2022 due to Certificate Expired
- Fixed in 8.10.196.0, latest 9800 releases, 8.5.182.12 (8.5.182.13 for 3504) and 8.5.182.109 (IRCM, 8.5.182.111 for 3504)
Field Notice: FN70479 AP Fails to Join or Joins with 1 Radio due to Country Mismatch, RMA needed
How to avoid boot loop due to corrupted image on Wave 2 and Catalyst 11ax Access Points (CSCvx32806)
Field Notice: FN74035 - Wave2 APs DFS May Not Detect Radar After Channel Availability Check Time
Leo's list of bugs affecting 2800/3800/4800/1560 APs

QingwYang82917 · ‎01-28-2021

Thanks for your help! I will try another device to replace WMIC 3201.

Best wishes,

Yang

QingwYang82917 · ‎01-28-2021

Thanks for your help! I will try another device to replace WMIC 3201.

Best wishes,

Yang