Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Resolved! WLC2504 Access Point not joining
Hello,I have a WLC2504 with 10 licenses running 8.5.151.0.I have several 3602 AP's with AC radio module that previously could join the controller, but now don't join the controller anymore. As reason for the failed join attempt I read: Missing AP Man...
Resolved! Different AP models
Hi all We have MR45 APs in place in one of our offices, now we need to extend this office with more APs. MR45 APs are end of sales and I want to go with MR44, from the roaming prospective is the MR45 compatible with MR44? Or are there any issues? Of ...
I have Cisco 2504 Wlan Controller and 12 APs. Yesterday I tried to update system starting by uploading new FUS.I didn't do any preloading stuff since our WLAN is only use in working hours. Now it has not been accessible for almost 20 hours and other ...
Hi,We are (have to) deploying wired dot1x on our network. We are using Cisco APs (2700, 2800, 9120 models), some locations in local switching mode, some locations in central switching mode. What is the recommended configuration switch LAN port config...
I know it's not very scalable but for a temporary solution I've been asked if there's a limit to the number of clients that can connect to an SSID with one set of credentials in the "User management portal".Can't see anything documented.
Hi all,I have an iPad here that regularly loses connection.Catalyst 9800-CL 17.3.3FT-802.11x onOther Apple devices are behaving normally. The first strange thing is that every few minutes there is an "Association received" and after a few more minute...
Cisco 5520 WLC Version 8.5.151ISE 2.7Cisco AnyConnect 4.10Cisco 3702Is it expected behavior for a authenticated and connected client to be disconnected when the flexconnect AP goes into standalone mode? I was under the impression that currently authe...
Good Morning, Meraki wizards.I have a project to cover an exterior farm of about 4.5 acres, that needs complete coverage. if each AP is wired I was considering 4 one on each corner facing inwards, if not wired I would have 5 main one would be wired i...
When doing Stick Survey I use a 9120 with EWC or a 2802 with MobilityExpress, mount it on a camera stand and use Ekahau with sidekick to measure signal strength and other various metrics. But how does my settings in the AP really reflect how RRM will...
Sinds yesterday I have a cisco aironet 1815i. I did start configuring with the cisco mobility express for phones. After I made a configuration I would change it. Only I can't change any configuration. So, I decided to factory reset the AP. Only if I ...
Hello,I have 2 C9800-CL WLCs Version 17.3.5b running on Hyperv, they are forming a working HA/SSO cluster.Last week, we had to patch the host where the 2 controllers were located, so we had to migrate the 2 VMs to another hosts, and the cluster has b...
Hi. I have a 9120AXI ap running version 17.3.6.76. I have a 10 ap's in production that I runs 17.6.1.13 code. I want this new ap to join the EWC controller instead of upgrading all 10 ap's in production to newest release for now. If that is possible....
Resolved! Azure SSO login fails after MFA
HelloI've followed these two articles to set up SSO logins:https://documentation.meraki.com/General_Administration/Managing_Dashboard_Access/Configuring_SAML_SSO_with_Azure_ADTutorial: Azure Active Directory single sign-on (SSO) integration with Mera...
Hello Experts, We are a small org with mix of fifty Aironet 3702s and 3802s access points managed by 5508 dual controller in HA setup. This summer we are planning to upgrade it with Embedded Wireless Controller (EWC) running on Catalyst 9130AX acce...
Resolved! QoS for "Fuze" voip and conferencing
Hello,I am trying to add DSCP tagging on our MR36's for our VOIP and video conferencing software called "Fuze" (aka 8x8).I have this from their documentation - Would adding a rule of "all voip and video conferencing" (there isn't a specific definitio...
