02-19-2019 03:15 AM
Hi,
We're in a bit of a problem right now, we have a MOD400-TR + MPA-2x100G and when we plug into the ASR9006-V2 or ASR9010-V2 chassis throw the following warning:
%FABRIC-FIA-1-RATE_LIMITER_ON : Set|fialc[163908]|0x1073000|Insufficient fabric capacity for card types in use - FIA egress rate limiter applied
And of course if i check the throughput on the MPA ports the RX is arounf 100G but the TX is around 39G.
RP/0/RSP0/CPU0:ios#show ver bri
Tue Feb 19 11:50:38.442 UTC
Cisco IOS XR Software, Version 6.4.2[Default]
Copyright (c) 2018 by Cisco Systems, Inc.
ROM: System Bootstrap, Version 0.76(c) 1994-2012 by Cisco Systems, Inc.
ios uptime is 16 minutes
System image file is "disk0:asr9k-os-mbi-6.4.2/0x100305/mbiasr9k-rsp3.vm"
cisco ASR9K Series (Intel 686 F6M14S4) processor with 12582912K bytes of memory.
Intel 686 F6M14S4 processor at 2128MHz, Revision 2.174
ASR 9006 4 Line Card Slot Chassis with V2 AC PEM
1 FastEthernet
2 Management Ethernet
2 HundredGigE
2 DWDM controller(s)
503k bytes of non-volatile configuration memory.
6271M bytes of hard disk.
12510192k bytes of disk0: (Sector size 512 bytes).
12510192k bytes of disk1: (Sector size 512 bytes).
RP/0/RSP0/CPU0:ios# show diag sum
Tue Feb 19 11:50:42.794 UTC
NODE module 0/RSP0/CPU0 ASR9K Route Switch Processor with 440G/slot Fabric and 12GB
NODE module 0/1/CPU0 400G Modular Linecard, Packet Transport Optimized
MPA 0/1/0 : ASR 9000 2-port 100GE Modular Port Adapter
RP/0/RSP0/CPU0:ios#
Could anyone guide me in how to solve this, i did the same exactly configuration for another customer not so long ago and was working fine (so 100G TX/100G RX).
Regards,
02-19-2019 06:24 AM
Do you only have a single RSP?
02-19-2019 07:01 AM
Hi Tkarnani,
First test (the one for the other customer that was working) was only with one RSP440 but this one i tested with one and two SUPs.
I forgot to mention in my first message that i was using a really basic L2 config (ports configured as l2transport and assigned to the same bridge domain).
Right now i have it working in basic L3 but would like to know why in the past it worked in L2 with only one supervisor.
Regards,
02-20-2019 07:24 AM
There are quite a few variables here.
1st , with 1 RSP the fabric will be limited to 220G
2nd, we do not know the dest port, if its a 10G line card for example there is a limitation of VOQ size, which will only allow 13-18G per flow (from 100G LC to 10G LC)
3rd, we do not know the packet size, if it is small size packet for example there is a chance the NP is being overwhelmed and experiencing tail drops
let me know if you have any additional questions
Thanks!
02-21-2019 01:46 AM
Hi,
I understand the fist point, last test was with 2 RSP.
2) Traffic flows from 1 port of the 2x100G to the other (just a required proof for the customer).
3) packet size is 9000 and mtu is configured as 9216 in both interfaces.
Regards,
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide