07-10-2011 03:43 AM
Hi these.
I configurated tunnel IPv6 over IPv4. Althought interface tunnel is up.
But on SW_AGG_01, only ping successful: 1001:1:1::1, not ping 1001:1:1::2.
The same on SW_AGG_02, only ping successful: 1001:1:1::2, not ping 1001:1:1::1.
I don't know cause of problem.
Can everyone help me ????
Thanks.
interface tunnel-ip100
ipv6 nd ns-interval 1000
ipv6 nd ra-interval 3
ipv6 address 1001:1:1::1/48
ipv6 enable
tunnel ttl 100
tunnel source GigabitEthernet0/0/0/0
keepalive 10
tunnel destination 172.16.16.1
!
interface GigabitEthernet0/0/0/0
description For ATP
mtu 9192
ipv4 address 172.16.16.2 255.255.255.252
negotiation auto
transceiver permit pid all
!
SW_AGG_01#show interfaces tunnel-ip 100
Sun Jul 10 15:46:21.334 VN_TIME
tunnel-ip100 is up, line protocol is up
Interface state transitions: 2
Hardware is Tunnel
Internet address is Unknown
MTU 1500 bytes, BW 100 Kbit (Max: 100 Kbit)
reliability 255/255, txload 0/255, rxload 0/255
Encapsulation TUNNEL_GRE, loopback not set,
Tunnel TOS 0
Tunnel mode GRE IPV4,
Keepalive is enabled, interval 10 seconds, maximum retry 3
Tunnel source 172.16.16.2 (GigabitEthernet0_0_0_0), destination 172.16.16.1
Tunnel TTL 100
Last input never, output 2d04h
Last clearing of "show interface" counters never
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
690 packets input, 26200 bytes, 0 total input drops
0 drops for unrecognized upper-level protocol
Received 0 broadcast packets, 0 multicast packets
3 packets output, 192 bytes, 0 total output drops
Output 0 broadcast packets, 0 multicast packets
SW_AGG_02:
interface tunnel-ip100
ipv6 nd ns-interval 1000
ipv6 nd ra-interval 3
ipv6 address 1001:1:1::2/48
ipv6 enable
tunnel ttl 100
tunnel source GigabitEthernet0/0/0/0
keepalive 10
tunnel destination 172.16.16.2
!
interface GigabitEthernet0/0/0/0
description For ATP
mtu 9192
ipv4 address 172.16.16.1 255.255.255.252
negotiation auto
transceiver permit pid all
!
SW_AGG_02#show interfaces tunnel-ip 100
Sun Jul 10 15:49:04.812 VN_TIME
tunnel-ip100 is up, line protocol is up
Interface state transitions: 2
Hardware is Tunnel
Internet address is Unknown
MTU 1500 bytes, BW 100 Kbit (Max: 100 Kbit)
reliability 255/255, txload 0/255, rxload 0/255
Encapsulation TUNNEL_GRE, loopback not set,
Tunnel TOS 0
Tunnel mode GRE IPV4,
Keepalive is enabled, interval 10 seconds, maximum retry 3
Tunnel source 172.16.16.1 (GigabitEthernet0_0_0_0), destination 172.16.16.2
Tunnel TTL 100
Last input 2d03h, output 2d04h
Last clearing of "show interface" counters never
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
689 packets input, 26212 bytes, 0 total input drops
0 drops for unrecognized upper-level protocol
Received 0 broadcast packets, 0 multicast packets
3 packets output, 192 bytes, 0 total output drops
Output 0 broadcast packets, 0 multicast packets
07-19-2011 01:37 PM
IPv6 over IPv4 GRE is not yet supported on the ASR 9000.
I believe that it is planned but not yet anounced what release it will be provided in.
06-26-2018 07:45 PM
Hi David,
do we have support now?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide