cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1973
Views
5
Helpful
2
Replies

ASR-9000: config tunnel IPv6 over IPv4

trantienhung_hn
Level 1
Level 1

Hi these.

I configurated tunnel IPv6 over IPv4. Althought interface tunnel is up.

But on SW_AGG_01, only ping successful: 1001:1:1::1, not ping 1001:1:1::2.

The same on SW_AGG_02, only ping successful: 1001:1:1::2, not ping 1001:1:1::1.

I don't know cause of problem.

Can everyone help me ????

Thanks.

interface tunnel-ip100

ipv6 nd ns-interval 1000

ipv6 nd ra-interval 3

ipv6 address 1001:1:1::1/48

ipv6 enable

tunnel ttl 100

tunnel source GigabitEthernet0/0/0/0

keepalive 10

tunnel destination 172.16.16.1

!

interface GigabitEthernet0/0/0/0

description For ATP

mtu 9192

ipv4 address 172.16.16.2 255.255.255.252

negotiation auto

transceiver permit pid all

!

SW_AGG_01#show interfaces tunnel-ip 100

Sun Jul 10 15:46:21.334 VN_TIME

tunnel-ip100 is up, line protocol is up

  Interface state transitions: 2

  Hardware is Tunnel

  Internet address is Unknown

  MTU 1500 bytes, BW 100 Kbit (Max: 100 Kbit)

     reliability 255/255, txload 0/255, rxload 0/255

  Encapsulation TUNNEL_GRE,  loopback not set,

  Tunnel TOS 0

  Tunnel mode GRE IPV4,

  Keepalive is enabled, interval 10 seconds, maximum retry 3

  Tunnel source 172.16.16.2 (GigabitEthernet0_0_0_0), destination 172.16.16.1

  Tunnel TTL 100

  Last input never, output 2d04h

  Last clearing of "show interface" counters never

  5 minute input rate 0 bits/sec, 0 packets/sec

  5 minute output rate 0 bits/sec, 0 packets/sec

     690 packets input, 26200 bytes, 0 total input drops

     0 drops for unrecognized upper-level protocol

     Received 0 broadcast packets, 0 multicast packets

     3 packets output, 192 bytes, 0 total output drops

     Output 0 broadcast packets, 0 multicast packets

SW_AGG_02:

interface tunnel-ip100

ipv6 nd ns-interval 1000

ipv6 nd ra-interval 3

ipv6 address 1001:1:1::2/48

ipv6 enable

tunnel ttl 100

tunnel source GigabitEthernet0/0/0/0

keepalive 10

tunnel destination 172.16.16.2

!

interface GigabitEthernet0/0/0/0

description For ATP

mtu 9192

ipv4 address 172.16.16.1 255.255.255.252

negotiation auto

transceiver permit pid all

!

SW_AGG_02#show interfaces tunnel-ip 100

Sun Jul 10 15:49:04.812 VN_TIME

tunnel-ip100 is up, line protocol is up

  Interface state transitions: 2

  Hardware is Tunnel

  Internet address is Unknown

  MTU 1500 bytes, BW 100 Kbit (Max: 100 Kbit)

     reliability 255/255, txload 0/255, rxload 0/255

  Encapsulation TUNNEL_GRE,  loopback not set,

  Tunnel TOS 0

  Tunnel mode GRE IPV4,

  Keepalive is enabled, interval 10 seconds, maximum retry 3

  Tunnel source 172.16.16.1 (GigabitEthernet0_0_0_0), destination 172.16.16.2

  Tunnel TTL 100

  Last input 2d03h, output 2d04h

  Last clearing of "show interface" counters never

  5 minute input rate 0 bits/sec, 0 packets/sec

  5 minute output rate 0 bits/sec, 0 packets/sec

     689 packets input, 26212 bytes, 0 total input drops

     0 drops for unrecognized upper-level protocol

     Received 0 broadcast packets, 0 multicast packets

     3 packets output, 192 bytes, 0 total output drops

     Output 0 broadcast packets, 0 multicast packets

2 Replies 2

David Powers
Cisco Employee
Cisco Employee

IPv6 over IPv4 GRE is not yet supported on the ASR 9000.

I believe that it is planned but not yet anounced what release it will be provided in.

Hi David,

 do we have support now?

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: