- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-15-2020 07:53 AM - edited 09-15-2020 07:59 AM
Cisco ASR-9006
When making any changes, the system returns this to me when using the commit. Can anyone help me in this matter?
------------------------------------------------
router exit after commit
% Failed to commit .. As an error (Unknown) encountered during commit operation. Changes may not have been committed:
'CfgMgr' detected the 'fatal' condition 'The Configuration Manager has encountered a file i/o error.': Value too large to be stored in datatype
Solved! Go to Solution.
- Labels:
-
XR OS and Platforms
Accepted Solutions
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-16-2020 11:39 AM
Can you get authorization for "show nrs handles data all | i "/etc/cfg/lr/" | utility wc lines"?
Also I don't see any output for "show install active summary". What version of code are you running?
There is 1 bug you could be hitting if we get the show nrs output, otherwise its possible the OS is corrupted and we need to turboboot the box based on the show ip int bri output.
Sam
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-15-2020 07:56 AM
Not sure what is the device model and IOS running on it.
some bug show same symptoms worth looking at :
https://bst.cloudapps.cisco.com/bugsearch/bug/CSCsg23286/?rfs=iqvred
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-15-2020 07:58 AM
ASR - 9006
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-15-2020 10:22 AM
What code are you on?
Can you try a 'cfs check' from XR exec prompt and then try to commit your change?
Thanks,
Sam
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-15-2020 01:19 PM
cfs check command output...
RP/0/RSP0/CPU0:LIVERPOOL#cfs check
Mon Sep 15 04:07:54.893 UTC
Creating any missing directories in Configuration File system...OK
Initializing Configuration Version Manager...
Error in initializing Configuration Version Manager due to 'No such file or directory'.
Please fix the problem and reissue the 'cfs check' command.
Attempt to initialize version history encountered a temporary
failure. The Error is : No such file or directory.
This is expected to recover by itself please try again after a short while.
RP/0/RSP0/CPU0:LIVERPOOL#
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-16-2020 10:27 AM
Can you also provide the following?
show logging process rdsfs_svr
show nrs handles data all | i "/etc/cfg/lr/" | utility wc lines
fsck disk0:
show install active summary
Thanks,
Sam
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-16-2020 11:22 AM
RP/0/RSP0/CPU0:LIVERPOOL#show logging process rdsfs_svr
Tue Sep 16 01:51:01.568 UTC
Syslog logging: enabled (0 messages dropped, 0 flushes, 0 overruns)
Console logging: level warnings, 6195007 messages logged
Monitor logging: level debugging, 0 messages logged
Trap logging: level informational, 0 messages logged
Buffer logging: level debugging, 9734305 messages logged
Log Buffer (307200 bytes):
RP/0/RSP0/CPU0:LIVERPOOL#show nrs handles data all | i "/etc/cfg/lr/" | utility wc lines
% This command is not authorized
RP/0/RSP0/CPU0:LIVERPOOL#fsck disk0:
Tue Sep 16 01:53:57.349 UTC
FSCK results for partition /disk0: on node 0/RSP0/CPU0.
==============================================================
14463 block(s) recoverable - previously marked in the bitmap: FIXED
RP/0/RSP0/CPU0:LIVERPOOL#sh ip int br
Tue Sep 16 01:54:58.708 UTC
% The executable: show_ip_interface cannot be launched. Error: 'libovl' detected the 'fatal' condition 'No such file or directory'
RP/0/RSP0/CPU0:LIVERPOOL#show install active summary
Tue Sep 16 01:56:48.477 UTC
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-16-2020 11:39 AM
Can you get authorization for "show nrs handles data all | i "/etc/cfg/lr/" | utility wc lines"?
Also I don't see any output for "show install active summary". What version of code are you running?
There is 1 bug you could be hitting if we get the show nrs output, otherwise its possible the OS is corrupted and we need to turboboot the box based on the show ip int bri output.
Sam
