Hello everyone , I try to enable wanphy mode on NCS55A2 controller move to preconfigure state. may have any ideas or solutions?
RP/0/RP0/CPU0:Nov 12 09:42:41.846 UTC: config: %MGBL-CONFIG-6-INT_UNRESOLVED : Some of the interface configuration was moved to pre configuration automatically as these interfaces do not exist or could not be mapped to any nodes
try both two tips of sfp's SFP-10G-LR-S and SFP-10G-LR-S
controller preconfigure wanphy0/0/1/1 wanmode on
RP/0/RP0/CPU0:NCS_55A2#show platform Tue Nov 12 10:01:27.269 UTC Node Type State Config state -------------------------------------------------------------------------------- 0/0/1 NC55-MPA-12T-S OK 0/RP0/CPU0 NCS-55A2-MOD-SE-S(Active) IOS XR RUN NSHUT 0/RP0/NPU0 Slice UP 0/FT0 NC55-A2-FAN-FW OPERATIONAL NSHUT 0/FT1 NC55-A2-FAN-FW OPERATIONAL NSHUT 0/FT2 NC55-A2-FAN-FW OPERATIONAL NSHUT 0/FT3 NC55-A2-FAN-FW OPERATIONAL NSHUT 0/FT4 NC55-A2-FAN-FW OPERATIONAL NSHUT 0/FT5 NC55-A2-FAN-FW OPERATIONAL NSHUT 0/FT6 NC55-A2-FAN-FW OPERATIONAL NSHUT 0/FT7 NC55-A2-FAN-FW OPERATIONAL NSHUT 0/PM0 NC55-930W-DCFW OPERATIONAL NSHUT 0/PM1 NC55-930W-DCFW FAILED NSHUT
RP/0/RP0/CPU0:NCS_55A2#show install active summary Tue Nov 12 10:01:30.558 UTC Active Packages: 9 ncs5500-xr-6.6.25 version=6.6.25 [Boot image] ncs5500-mgbl-126.96.36.199-r6625 ncs5500-li-188.8.131.52-r6625 ncs5500-isis-184.108.40.206-r6625 ncs5500-mcast-220.127.116.11-r6625 ncs5500-ospf-18.104.22.168-r6625 ncs5500-mpls-22.214.171.124-r6625 ncs5500-mpls-te-rsvp-126.96.36.199-r6625 ncs5500-k9sec-188.8.131.52-r6625
RP/0/RP0/CPU0:NCS_55A2#show inventory Tue Nov 12 10:02:33.931 UTC NAME: "0/0", DESCR: "NC55A2 MOD Scale Virtual Line Card" PID: NCS-55A2-MOD-SE-S , VID: V01, SN: FOC231978CS
Crosswork Cloud - Crosswork Traffic Analysis - FAQ
Crosswork Cloud - Crosswork Traffic Analysis is a Cloud-hosted Software as a Service platform that provides Netflow based Traffic Analytics. The Crosswork Traffic Analysis platform Traffic Analysis, Peeri...
Cisco Champion Radio · S8|E9 Innovations to Achieve a Trustworthy Infrastructure
How do you know for certain that a router in your network has not been altered with since you deployed it? Wouldn’t it be great if you can cryptographically challenge your r...
IOS upgrade on asr9xx mandates rommon upgrades sometimes while they can be optional at other times. You may land up in unwanted situation if proper procedure is not followed during upgrades.
This article will include complete details about rommon ...
In some situation NCS560 RP become unresponsive after reload or powercycle.
In many NCS560 deployments are in remote location, deployment might be large and human intervention should be kept at minimum
Engineering team have been working on a str...
In simple terms, 'Route Churn' is defined as the 'rate of change of prefixes'. Different XR versions across 4.x to 7.x have differing behavior & support for the BGP churn handling and some enhancements made from 6.5.3 onwards (listed in appendix) mak...