cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2249
Views
0
Helpful
2
Replies

Troubles with Install License for VRF

saul.reyes
Level 1
Level 1

Hi

actually we have two ASR 9000 with follow info:

RP/0/RSP1/CPU0:ED_MEX_1#show license

Tue Oct 22 09:10:06.835 UTC

FeatureID: A9K-AIP-LIC-B (Slot based, Permanent)

Total licenses 2

Available for use 2

Allocated to location 0

Active 0

Store name Permanent

Store index 1

Pool: Owner

Total licenses in pool: 2

Status: Available 2 Operational: 0

RP/0/RSP1/CPU0:ED_MEX_1#admin show license udi

Tue Oct 22 09:10:20.379 UTC

Local Chassis UDI Information:

PID : ASR-9010-AC-V2

S/N : FOX1645GA37

Operation ID: 2

RP/0/RSP1/CPU0:ED_MEX_1#

En el EDGE 2:

RP/0/RSP0/CPU0:ED_MEX_2#show license

Tue Oct 22 09:14:28.184 pst

FeatureID: A9K-AIP-LIC-B (Slot based, Permanent)

Total licenses 1

Available for use 1

Allocated to location 0

Active 0

Store name Permanent

Store index 1

Pool: Owner

Total licenses in pool: 1

Status: Available 1 Operational: 0

RP/0/RSP0/CPU0:ED_MEX_2#admin show license udi

Tue Oct 22 09:14:37.356 pst

Local Chassis UDI Information:

PID : ASR-9010-DC-V2

S/N : FOX1645GA35

Operation ID: 1

but we have the same warning message from devices:

%LICENSE-ASR9K_LICENSE-2-INFRA_VRF_NEEDED : 2 VRF(s) are configured without

a valid license / license configuration for A9K-iVRF-LIC in violation of the

Software Right To Use Agreement. This feature may be disabled by the system

without the appropriate license. Contact Cisco to purchase the license

immediately to avoid potential service interruption.

Something know what happen

Best Regards

1 Accepted Solution

Accepted Solutions

Hi,

The license is marked as "available for use", but it is not "active". You might need to use the "license location" command to bind the license to a specific slot.

Florian

View solution in original post

2 Replies 2

Hi,

The license is marked as "available for use", but it is not "active". You might need to use the "license location" command to bind the license to a specific slot.

Florian

Hi Florian thamks for your response

we had the control window and we can check the follow:

We can move the first and only license on device generate between slots  but the error change for slot e.g.

Error on slot 3:
LC/0/3/CPU0:Nov 26 19:06:20.958 : rsi_agent[307]: %LICENSE-ASR9K_LICENSE-2-INFRA_VRF_NEEDED : 1 VRF(s) are configured without a valid license / license configuration for A9K-iVRF-LIC in violation of the Software Right To Use Agreement. This feature may be disabled by the system without the appropriate license. Contact Cisco to purchase the license immediately to avoid potential service interruption

Error then we moved the license location to slot 3 from slot 2:

Error on slot 2 now and slot 3 is now operation correctly
LC/0/2/CPU0:Nov 26 19:56:15.855 : rsi_agent[307]: %LICENSE-ASR9K_LICENSE-2-INFRA_VRF_NEEDED : 2 VRF(s) are configured without a valid license / license configuration for A9K-iVRF-LIC in violation of the Software Right To Use Agreement. This feature may be disabled by the system without the appropriate license. Contact Cisco to purchase the license immediately to avoid potential service interruption.

We think that we´ll need it 4 license type A9K-AIP-LIC-B one for each slot.

thanks for your response

Best Regards

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: