Hi, for a few weeks I have been facing this error "No applications have been installed." on my cucm at version 12.5 when I try to go to the ccmadmin interface. After my research, I read that it was a recognized bug, but I couldn’t figure out how to f...
Hello,I'm new to learning VOIP on Cisco phones, and I'm having trouble finding clear information about the following Cisco technologies:Cisco Unified CM (CallManager) PUB SUBCisco Unity Connection Administration PUB SUBCisco Unified Attendant Console...
Hi,We have multiple cisco room kits ranging from mini to Plus at a number of our client sites. We are having this issue where some the call and share screen buttons are appearing on the main display as well as being on the touch panel. I've been thro...
I have two VoIP applications installed on my computer that use my audio device, specifically a JABRA headset. When I receive a call on CISCO WEBEX, I need to check the "RETRAIT" box on ALCATEL LUCENT IPSOFTPHONE to avoid receiving a duplicate call on...
Hello Team, for a company with fewer than 30 users. What is the least expensive on-premise solution to offer to implement a CISCO collaboration solution?
Hi dears,We configured a sip trunk with our provider. we successfully registered but incoming calls are not working. We get disconnect cause 102. Can you please helpMy router config : FUIG#sh runBuilding configuration... Current configuration : 19227...
Hi allI installed cucm 12.5 and I encountered a problem.I have two networks 192.168.15.0/24 the server is installed in this network. and the second network 192.168.16.0/24. I installed Cisco 7821 telephones in these two networks except that the telep...
Bonjour, Nous utilisons présentement un système Be6000 et lorsque nous programmons un renvoi d'appel sur nos téléphones (modèle 7945) vers des numéros externes, cela fonctionne parfaitement lorsque l'appel d'origine provient d'un poste interne, mais ...
HI GuysI have a 2921 router for Outgoing calls to itsp with sip connection.this router is Voice Gateway and Data Gateway for SIP Ip phonei want to configure srst for those ip phone on this router but when connection lost with cucm srst does not worki...
Hi everybody,I need your help. We have a CUCM 12.5 cluster. In the same building, we have Phone A and Phone B. If Phone A calls Phone B or Phone B calls Phone A, Phone B doesn't hear Phone A, but Phone A hears Phone B. If Phone A calls other phones, ...
Bonjour, je voudrais savoir si l'on pouvait utiliser le Cisco SPA122 pour connecter sa ligne Orange, donc une Livebox 6, à un serveur en SIP sous FreePBX Asterisk. Si oui, pourriez-vous m'éclairer un peu ? Car lorsque je branche ma ligne sur le port ...
Bonjour, nous utilisons des Téléphone IP 8821 et nous n'avons pas l'option pour transférer les appels(System version: 12.5.1.16900)comment l'activer dans les paramètres sur call manager? en vous remerciant par avance Cordialement,
Bonjour, Nous souhaitons supprimer la fonction de bip d'appel dans les casques et combinés lorsque nous sommes en conversation ?Nous n'avons pas trouvé cette information dans le guide du téléphone, et ces bips étant présents aussi au combiné nous pen...
Hi,Does anyone know the XML configuration for configuring a SIP password on a cisco ata 190 or a cisco 8831 ? I looked everywhere and found nothing. Is it possible to indicate this in the XML configuration?Unfortunately, I don't have access to cucm a...
Bonjour,Désolé d'avance si mon post n'est pas dans le bon forum.J'utilise UC-One Communicator 22.9.40.Celui-ci crashe sans arrêt, plusieurs fois par jour :* les correspondants ne m'entendent pas quand j'appelle* la communication se coupe en pleine ap...
