Hello All, we have 3 APIC cluster in our ACI fabric. With this we can connect maximum 80 leaf. Now leaf count is increasing because of requirement. If i increase the cluster size from 3 to 5 , i can add up to 400 leaf. kindly answer below queries:-...
Forum Posts
Hello Guys, We are running small ACI setup with 3 units of APIC-SERVER-M2 (UCS C220 APIC-Server-M2) which will be EOS by 30june2024. Upon checking internally we found that , we can replace existing APIC-M2 with new APIC-M4 and we need to upgrade curr...
When deploying Cisco ACI, can I first build each site with a DCN Essentials license and later upgrade the Essentials license to Advantage to build Multi-Site?
Hi,In the same way that ACI, when integrated with Kubernetes can load balance outside requests to a particular exposed service, is it possible to manually configure ACI for basic L3/L4 load-balancing of regular of servers, announcing the /32 IP to th...
I feel like I'm missing something that should be obvious. I'm at a loss for identifying where to define a host or a subnet as a source or destination within the contract policy heirarchy.If I have a contract, I can specificy allowed/denied TCP and UD...
Hello Guys.Is it possible to redirect traffic (using a PBR or any other way) to one IP in ACI? The case is like this:There is an F5 balancing a service to a cluster of servers. The thing is that when the traffic needs to return, the servers that are ...
Hi all - We have been working to integrate Rancher Kubernetes into our ACI environment utilizing the Cisco ACI-CNI. Having issues with understanding our the External Routers (Cat 8kV) is suppose to be configured for the exposed service IP address. C...
Under Fabric-Inventory-Pod x- Leafxxx-Interfaces-Physical Interfaces-Eth1/1 you can add a Description to that port. Login to the leaf and do a show interface status shows the description.Is there a way to set this description with ansible or terrafo...
Hi guys,I am setting a fabric with 3 APIC M4 having VIC 1455 cards ... Each APIC VIC port-3 and VIC port-1 goes to Leaf 1 and 2 according to the topology below. Problem : APIC 1 can't see other 2 APICs. APIC 1 registers Leaf 1 and Leaf 2 but each rem...
Hi,I am troubleshooting an issue with an L3OUT that is bouncing/flapping periodically. It looks to me to be a physical issue but I am struggling slightly. The ACI switch is a Nexus 93180YC-FX which is connected to my core which is C9500-48Y4C. Bot...
Resolved! where are APIC shards located ?
There are many control functions which APIC provides like policy manager, topology manager, VMM etc. Can someone please answer where are these located in cisco APIC and how i can see them.ThankyouNitesh
Can we stretched epg and bridge-domain between two sites without MSO I have EP1 (10.10.1.100/24) on the site 1 and GW 10.10.1.1 on the site 1 I want to move EP2 from site 1 to site 2 with the same broadcast domain (10.10.1.0/24) but I didn't find any...
Hi Team,We have the below Model Switch in our infra where by default some configurations are appearing under the few interfaces.What could be the reason for this .Please help on this.Also please help me the command to clear all the interface config ...
Question for those running the new APIC M4. Do you see 4 or 6 interfaces on the interface tab of the APIC in the GUI. Historically i have seen 4 but with the APIC M4 ACI 6.03, i see six. Fabric is discovered, database is fully fit, F0103 alarms ar...
Not sure what the best approach here is so I am asking for recommendations. Customer has ALL EPGs configured in “Preferred Group” status but has an OS\Application server that meeds segmentation and also wants L7 visibility. I think the best approach ...
