Any idea? The vmmmgr process seem to have problem, and creating EPC in apic does not create port-group in vm DVS. We are unable to downgrade back to 1.0(3n) because controller health is not in "fully fit" state.
Any idea? The vmmmgr process seem to have problem, and creating EPC in apic does not create port-group in vm DVS. We are unable to downgrade back to 1.0(3n) because controller health is not in "fully fit" state.
Hi,My old firmware is n9000-11.0(2j) and apic-1.0(2j).I have done upgrade firmware apic-1.1(1j) on controller and n9000-11.1(1j) on 2 Leafs.But when i upgrade firmware n9000-11.1(1j) on 2 Spines, it returns fail. I got some picture for faults log ( ...
I want to know if I can upgrade the ACI Fabric to v1.1(1j) straight from v1.0(2j)? The release notes for 1.1(1j) only shows these examples: Upgrading the APIC ControllerTable 2 contains the supported APIC upgrades.Table 2 Supported APIC UpgradesFromT...
Hello Can someone explain the significance of the Multicast address that gets provisioned on the Bridge Domain? thanks
Hi, Team Need your help , our LAB APICs were connected to leaf switch by using 10G fiber connections and APICs were discovering fine.but since we have 1G copper SFP , we are try to replace fiber with the copper. but after swap , nothing is working. I...
Hello, I'm not clear why/when we need to associate a physical domain with an EPG? Without associate the EPG with a physical domain, the EPG can pass the traffic OK through static path binding. The front panel ports can get active vlans from AEP->doma...
Is the latest cisco VSUM 1.2.2 which release on 7-May-2015 compatible with esxi 6.0?
Guys, Is there a way a can police traffic on ACI. I need to limit traffic on a particular EPG, i know i can create a custom QoS policy but not sure how i can rate limit it.I figured i could probably mark the traffic and then send into 7k and police ...
HiI have downloaded ACI Python samples provided by cisco on github. I searched using Python pip search for cobra but couldn't find any relevant library. Please let me know where could I get the python cobra library for ACI samples. Many Thanks Mehran
Hello,We have a loaner ACI simulator UCSC-220 box which we have installed the simulator software on, however we are having trouble getting it fully configured and usable. Each of the 3 APICs have been configured with IP addresses, following the inst...
Hi, ...regarding the limitation of a stretched ACI Fabric of 30km's - what's the max delay tolerated by the solution?When using a DWDM system, longer distances might be possible, if delay's are still acceptable? Thanks, Andy
Hi There, Could anyone help me find out the maximum tenants can setup in Cisco ACI. My understanding is it can support 64k tenants base on document below. however someone said it only support 100 tenants and it will grow to 500 in the future. Could ...
I need to route leak between VRFs in the same tenant, i know how to do it for Inter Tenant but i cannot get it working when inside the same tenant with two different VRFs using different BD. any ideas thanks
Would like to know if we can create a 3-arm design on the ASAv? Possible?
For L3 connectivity outside the fabric, I config L3-out in tenant Common, I want to share L3 connection for multi tenants. How to do this.Please help me!Thanks.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-17-2024 08:10 AM | ||
09-16-2024 01:50 PM | ||
09-13-2024 06:40 AM | ||
09-12-2024 07:01 AM | ||
09-12-2024 12:54 AM |
User | Count |
---|---|
2 | |
1 | |
1 | |
1 | |
1 |