Heads Up :
The post you are writing will appear in a public forum. Please ensure all content is appropriate for public consumption. Review the employee guidelines for the community here.
What is the command that can show the ACE Bundle (Like: ACE-4710-02-K9, ACE-4710-04-K9). We have ordered one ACE with 4G BW, and another one with 2G BW. But nothing shows this fact using "show hardware" and "show inventory" commands !
In general, Primary and Standby CM's database tables, configurations, group polices should be sync'd up and looked identical, right? What else will be different and will require to import onto standby CM manually? Things like: SSL certificate, Secu...
Good afternoonI need your help.I´m trying to perform a snmp query to get the status of the reals of a serverfarm.Basically I´m trying to get an output that tells me if the reals of a specific serverfarm are Operation or Probe_Failed.What is the OID t...
Hi there,I'm trying configure and test proximity based responses on the GSS (v3.2) and I'm having trouble understanding how the decisions are being made. As far as I can tell, it doesn't seem to be working. For the test, I've configured three websi...
I recently replaced a WAVE 574 in the data center with vWAAS. That has gone fine with no problems. I deleted the WAVE 574 from the CM about 3 weeks ago and now am re-purposing the device at a new remote site. I can ssh to the device , it is poi...
show stat dreCache:Status: Usable, Oldest Data (age): 4d9hTotal usable disk size: 116735 MB, Used: 95.21%Does this look normal? Sould I be concerned? What should be done to reduce the usage?ThanksJoe
Hello,I have a handful of brand new Cisco WAVE 294's and 594's. I need to downgrade the code from 4.4.5 to 4.4.3. I have the new code on my usb drive, which is readable by my laptop. However, when I plug the device into the 594 and run the "lsusb"...
Hi all I am working on a DataCenter architecture where we would like to implement Nexus 7000. For the time being, there only one "context" but we may take the opportunity to implement VDC in a later future I was not able to find a clear answer on the...
Hi there,I am new to the WAAS world and getting little confused with its terminlogy.When we look into different models (some are appliance based, some are modules).I was going thru the below link about WAAS appliances: http://www.cisco.com/en/US/prod...
Dear Folks,I'm trying to criate trafic policy based on the email domain. For that, I need to know the email domain address.I will be able to know Layer 7 SMTP header and archive that?
Hello,Its strange to see the big difference in the system uptime and the kernel uptime. The ACE had caused a production impact for around 8 minutes and the standby ace didn't took over during that time frame although the FT/query vlan is configured p...
Hi All,We are running the ACE blade (A2.3.4) adn have the following configuration.A serverfarm configured:serverfarm host SF-GRG-Logger-7300 failaction purge probe GRG-Logger-7300 rserver GRG-LOGSRV-01 7300 backup-rserver GRG-LOGSRV-02 7300 ...
Hello, I am new to the ACE30. I a basic configuration from the CLI and I am trying to use the device manger. I am able to get to the web informational page rather then accessing the login page. I have rest the password for both the admin...
Hi,I am trying to set up a reverse telnet from a Router's Aux port to WAE694's console port.., but failed.. Here is the log,2012 Jun 4 02:39:56 HOCLWAAStest1 PAM_unix[6051]: %WAAS-UNKNOWN-3-899999: ### pam_unix: pam_sm_authenticate bad username [ 2...
