After the first loading WAE-674 the command "setup" is not executed through the console. NO-HOSTNAME#setupError opening terminal: vt100.NO-HOSTNAME#
Labels
-
Application Networking
(11,492) -
Community Feedback Forum
(1) -
Other Application Networking
(8) -
Other Data Center Subjects
(1) -
Other NAC
(1) -
Wide Area Application Services (WAAS)
(1,579)
Forum Posts
Hi folks,Some assistance if you have the time please.I'm running an ACE 4700 appliance, i have a 4 server serverfarm setup, non-ssl, with leastconns predictor...i have tried round robin as well, and nothing...I've taken each rserver out of service, a...
Hi,Is it all possible to use an ACE30 to RHI a VIP which acts as route for servers on LAN A to reach LAN B . We have 2xL2 WAN circuits between 2 sites used by only 4 servers for (different L3 subnets for the hosts). I`m considering using a VIP to loa...
Dear,My customer want to install a WAAS in six local remote site and a Site Central, but He has a ALLOT NetEnforcer, the Allot is doing Traffic Prioritization now.I will apreciate some comment about I can install the allot with WAAS.I am planing to s...
Hi,Where can I download ANM 5.1 for a trial? http://www.cisco.com/en/US/prod/collateral/contnetw/ps5719/ps6904/data_sheet_c78-687239.htmlRegardsStephen
I've been running into an issue with Cisco CSM for a number of years, but always found a way around it. Im attempting to get to the bottom of this to find out once and for all, if this is infact a limitation of the device, or a config issue/work aro...
Resolved! Problem with first boot Cisco WAE-674-k9
At the first loading WAE-674-K9 on the monitor screen there are messages:db_grub_start. S, Decommpressing Linux... done, booting the kernal. at the bottom there is Kernel alive and kernel direct mapping tables up to 140000000 800-e000Thus further oc...
How can ftp service on non-standard port be load balanced using Cisco ACE.For example ftp service required on tcp 2000 port
Resolved! wae 674
First time booting an appliance and instead of booting to setup wizard, it hangs at db_grub_start.S, Decommpressing Linux...done, booting the kernal. at the bottom there is Kernel alive and kernel direct mapping tables up to 140000000 @ 800-e000thank...
Is this normal to have millions of current connections within an ace 4710? There is only 3 current connections but shows a high number?Thanks!!
Hi,I´m Trying to sinchronize the clock whit NTP server external, these ntp server only support NTP version 3.Can I change the NTP version in the ACE4710 Appliance to support whit the ntp server external ?If is possible, How I can change it ?This is t...
Resolved! Show active mac pool on an ACE20?
I'm in a situation where I would like to add a vlan to a second context on a pair of redundant ACE modules. As soon as I open up that shared vlan box we will expose ourselves to mac conflicts until the shared-vlan-hostid commands can be implemented ...
I have a client that will not use my domain in connectivity to an application I am hosting. They want to add an entry in thier DNS using thier domain, but resolve it to an address that I have configured as a VIP on my CSS. I am terminating SSL for ...
Hi everyone,I have implemented an ACE in One Arm mode, and I need to know if is possible to apply SNAT with the same IP used as VIP address.For example:class-map match-all port-80-redaccion 2 match virtual-address 200.10.1.42 tcp eq wwwinterface vla...
Resolved! ACE design with inter-Vlan routing
Hello all.I'm working on a design for a customer where the ACE will perform inter vlan routing.A few questions about that :- is routed traffic enforced in hardware with some kind of CEF-like mechanism ? (I suppose yes because there is a FIB ? per htt...
