Heads Up :
The post you are writing will appear in a public forum. Please ensure all content is appropriate for public consumption. Review the employee guidelines for the community here.
Hi I have taken sniffer capture at both ends(source & destination) of communication but how can I track a single packet from both sides of capture. Is there any unique # tagged into the packet from which it can be identified that this is the pack...
Hello all,We have purchased WAAS WAE 674 WAN Accelerator's, and I have a question on placement in our network. I've just recently implemented redundant WAN Lines (DS3's), and now would like to move my WAE674's so that they are accelerating traffic a...
I have been tasked to provide ssl(https) access to a serverfarm that will be accessible from the internet. Is this the correct guide to follow?http://www.cisco.com/en/US/docs/app_ntwk_services/data_center_app_services/ace_appliances/vA3_1_0/configur...
I'm new to ACE and experiencing a small problem with a probe.I have this rather simple config on my ACE module, that loadbalance round robin between 2 servers.The probe I testing is just for checking the tcp port 8000:probe tcp PAPI port 8000 interva...
I will have two routers connected via T1. I would like to enable WAAS Express on both routers. Is a WAAS Central Manager etc. required or will this work just between the two routers?
Hello, I just received a pair of ACE 4710 to replace a single CSS. I have the ACE working in Bridge mode. However, I have an issue. I can access the http & https vips. I am not using source NAT as we need to see the "real" ip address of the end syste...
Hello,Just got a couple fo quick questions but no access to hardware at the mo.- If a WAAS appliance loses power unexpectedly will it recover or will someone need to press the power button?- Are there any plans to support iLO?We use pretty much all h...
Hello everyone,I need some help/advice on trying to the Flow Monitor function that is available. Basically I want to monitor the WAE's using Netflow, and I thought that by enabling Flow Monitor along with the host IP that I could monitor the traffic ...
Hi allHas anyone ever sucessfully loadbalanced dhcp with an ACE module?We use an ACE20-MOD-K9 with version A2(3.5). After I configured a policy which loadbalances everything to one rserver and one standby rserver it seems that it does not work as exp...
We are going to implement WAAS mobile without central manager and other WAE appliances. Just wondering if central manager is needed for WAAS mobile or WAAS mobile can run on its own.Thanks a lot
We're running v4.4.1 on both remote and data center WAE 7341s and we're seeing TCP resets during some of our HTTP connections.I'm just now beginning to look into the problem and noticed this the reset counters in 'show statistics tcp' such as:IKA-734...
I have a serverfarm with two real servers. I want one server to get 100% off the traffic, and the other server to only be used if server1 fails. So I setup server1 as active, and server2 as active standby. If server1 fails a probe, server2 should ...
Hello;I have an interesting issue with a configuration on the ACE module running A2_3_4 code.I have a server farm consisting of two servers and they are running SSL certificates under IIS. I am using a probe to verify if IIS & SSL is running.probe ht...
Hi,I need to configure ssl offloading so that user will send request on port 443 while ACE will so ssl offload so servers will handle http connection. my current config is as below(i haven't copied probe port80 here):rserver server1:80 ip add 192.168...
I received a 1941 G2 ISR from the Cisco Demo Pool today. It has 2 Gig installed and shows a permanent license for WAAS Express feature. I cannot figure out how to activate WAAS Express as there are no WAAS commands available.toreIndex: 1 Feature: W...
