We have multiple sites on each server. Is there a way to have the probe only stop traffic to a specific site or header and not take the complete rserver offline? ThanksGreg
We have 5 waas appliances including the CM (4 wae-512, 1 wae-674.) Starting with the CM, I upgraded all devices to SW version 4.3.1. After the upgrade and the devices came back online, one of the wae-512s reports an alarm "filesystem_size_mismatch...
Hi allI am trying to connect a link between my 6509 box and N5K boxThe link was functioning well , but now it is never upI have tried to change the SFP with no luckPlease check belowHQ-UM-CORE-VSS#show int Te2/8/1 transceiverTransceiver monitoring is...
Hi,Greetings. I can see Mr Siva is helping a lot on the discussions. Thank you so much for your contributions. We have configured Cisco ACE 4710 LB on our environment. One leg of LB is going to firewall for client side and another leg is connected to...
Hi -Did a packet capture on WAAS running L2 WCCP with switch, saw many tcp retransmission & dup ack packets, first i thought something is not right but then i looked back again, this may be corrected. Since WAAS is intercepting network traffic then ...
Hello, Recently I have implemented vPC on Nexus 5500 switches. On other side Router is connected with. The port-channel is configured in On mode.I got strange output from primary nexus: Nexus1# show vpc brief Legend: (*) - local vPC i...
Dera Sir/Madam, This is Robert from Chennai. We have constructed a new building in our office. We have Cisco 4507 switch in new building and having cisco 6509 core switch in Server room. We have lay out the single mode fiber between them. But the ...
Good day,I cannot locate any documentation regarding supported software versions on WAE/WAVE platforms. So will x74 platform range support 5.x software version, for example 5.3.1?Additionally what current recommended version for WAVE platforms? Thank...
Dear, While logging into DCNM in the inventory->switches I have couple of nexus 5K, on some of N5K the status its showing decryptionError, anyone has any idea what this error is, is it related to SNMP? Thanks,Aamir
I installed a virtual central manager, and configured IP, default gateway, and DNS name. The IP is pingable but https://CM-IP:8443 only shows "page can't be displayed". What other configurations I need to do for the virtual central manager to make it...
Transforming Cisco switches into highly scalable zero latency load balancers! Cisco Intelligent Traffic Director (ITD) does exactly that and much more!Cisco ITD has been selected as Best of Interop 2015 finalist in the Data Center Category. Finalist...
We are turning up a second data center for DR and will be using our ACE4710 to intercept DNS requests should Site A go down. We currently have two internet links, both 10G, both using Centurylink. Site A has a 10G connection, Site B has a 10G conne...
We have Two Wan routers WAN1 and WAN2 connected with diff ISP to DC.I have applied a wccp redirect on both routers creating sub-interface ---- going to Dist Switchinterface GigabitEthernet0/0.102 encapsulation dot1Q 102 ip address 172.16.148.33 255.2...
Hi guys,I had an e-mail from our Web team admin with a graph stating that there is an issue with the load balancing configuration.We've got two front end servers SDHSPWFE01, and SDHSPWFE02. According to the graph below, they can see http and https tr...
Hi Guys,We have a requirement to disable SSLv3 support and enable TLS1.0, 1.1 and 1.2 within our environment. Since having upgraded to A5(3.1a) we have available to us the ability to use TLS1.0, 1.1 and 1.2 according to the release notes, however in...
