Application Networking

Hello All,We've just deployed a scenario with CM/Core in our Main office and Edge in remote office. We're using DMPVN between offices with lowered MTU/MSS over the tunnels (1400/1360 respectively). The traffic itself between the offices works just fi...

I have configured an LDAP probe using the script provided. It is stuck in INIT state saying that No. Internal error: is incrementing. I have tried script LDAP_PROBE DEBUG but I don't know how to view the debug output. I have logging up and running an...

i want to make ethernet channel btween wae in data center & datacenter switch ,wae has two giga port and i use transperant wccp interseption is that possible as i need bandwidth more than 100MB btween wae & switch another Q did any one tested port sp...

Is there any possobility of problem if LAN side of inline group is set to 1Gb but WAN side is only 100 Mbps ? Also I can not see LAN and WAN settings in WAE-512K9 of 4.0.13 although this is clearly shown in 4.0.7 configuration of of 511.How would I l...

I have a point to point site with redundant links load sharing. I've installed a WAAS appliance on each end. We also have a Packetshaper installed on each end with shaping turned off. The setup is client -WAAS-Packetshaper-Router- Circuit-Router-PAck...

I put a couple web servers behind the ACE and it appears to work. But I cannot get to the internet. I'm assuming I need to enable NAT on the ACE and I read the SCE Security Guide. If I enable NAT on ACE for my outgoing traffic, will it impact the num...

Hi,I'm trying to answer a question while doing design. I am planning on deploying a CSM in bridge mode with multiple vlans. I need to create a serverfarm which has real servers in two separate server side vlans.I would then present the Vserver on the...

Forgive me if someone has asked this before - though I couldn't see anything relevant on a forum search.I have CSS box-to-box redundancy working fine. The servers we are load balancing have x2 adapters which are teamed with a cable to each CSS.If one...

Hi,The ACE permits to allocate finely ACE resource for each context.We can check the context resource usage by the command "sh resource usage".The Denied outputs gives details regarding the "Number of denied resources because of oversubscription or r...

When I try to enter the member [resource_class] command under the context config mode I get...Error: resources in useAny idea how I get around this?Note: I am trying to do this so that I can configure stickiness in my context and I getError: sticky r...

ip route 0.0.0.0 0.0.0.0 [6509-int-vlan11]ip route 1.1.8.0 255.255.255.0 [6509-int-vlan10]ip route 1.1.7.0 255.255.255.0 [6509-int-vlan10]Route Summary for Context C1 (RouteId 1)Route Source Count Memory (bytes)---------------------------------------...

Hi,I have configured a pair of CSSs for backend SSL. The setup includes self signed certificates. The server farm is two VMs with IIS6. HTTPS requests work like a charm. I am trying to get L5 stickiness with Arrowpoint cookies and i have a problem wh...

I have many server farms in various contexts and every single serverfarm shows something like this:NDCD23ACERT1/Internal-1295# sh serverfarm FINPROD88_80 detail serverfarm : FINPROD88_80, type: HOST total rservers : 3 description : - predictor : ROUN...

I am running out of IP's in a DMZ I have... I have a CSS in there.... Can I run a webserver on a different port of one of my servers.... and use the css to translate inbound port 80 and/or 443 traffic to the correct port based on URL?What would that ...

HI Experts,I have a requirement to select different content rules (also different services) for the same header URL, the only key differentiator is the fact that source IP will change.Flow is like this;WAPG/W - CSS11503 - HTTP proxy - CSS11503 (same ...