Application Networking

Hi The customer got one pair of CSM installed on two switches.Some servers connected to primary switch (primary CSM), and the rest of servers are connected to the 2nd switch/CSM.On the 2nd switch, sniffer shows a lot of unicast traffics are flooding ...

Hello , I have a problem with the configuration Active-Active VIP and Virtual Interface Redundancy, the VIP always is in MASTER, the secondary VIP is not put in backup. What happened?regardsGuillermo

6509 s/w catos upgrade question --------------------------------We have 3 x 6509 switches, each with Sup2 and MSFSC2 cards. These 6509's are running in hybrid mode (i.e. IOS for MSFC2 and Catos for Supervisor II card and IOS revision 12.1(13) on the ...

Is there a way to use a wild card cert in the CSS SSL Proxy list ?Looks like you can request a cert such as ABC*.xyz.com from Verisighn.Can you use that in a CSS for URLS likeABC1.xyz.comABC2.xyz.comABC3.xyz.comand only use one VIP ?ThanksSteve

Suppouse that there is two servers providing service for remote aplications. Those aplications using IPSEC in transport mode. I would like to put at front CSM to load-balance beetwen both of them (persist via SRC IP is ok for me). Have you any expiri...

Hi, I have redundant 11503s (sg0730106 standard feature) configured with VIP redundancy, accepting incoming SSL requests, then talking to backend ssl servers. The CSS are deployed in a "one-armed" network - packets go in and out the same interface. ...

Does Cisco have a link aggregation product similar to Radware's LinkProof or FatPipe's Warp?If so, what is it?Thanks,Jason

I'd like to implement a policy based on return-code. The algorithm is as below,If HTTP return-code == 500 to 600 serverfarm1else serverfarm2We have a CSM V3.2. Can someone tell me if this is doable? If yes, would you please tell me how. App...

Hi i configured the wafs engine with wccp. On my router i see the counter increasing but how can i verify if the File engine is performing well? How can use the Cisco Benchmark Tools with wccp ?any help is apreciate!Thanks.

Hi,Here is my topology 6500A ---dot1q-----6500B \ / \ / \ / Cache Engine The cahce engine has two interfaces, one one each switch. Both are configured to listen to incoming request. If i have a ho...

I've upgraded both Cisco CSS11506 Load Balancer to ver 7.5. However, the Box-to-Box LoadBalancer is not running when " show redundancy". Box A configurecircuit VLAN1 description "Management VLAN for SW2950" ip address 192.168.xx.253 255.255.255.224...

After the script complete's it reports : File copy Vipr Config Sync Failed. Commit unsuccessful! localconfig: 24727 bytes remoteconfig : 24653 bytesI've looked through the config but it's rather large and could really do with some pointers to help...

HiI am doing a migation from alteon AD3 to Cisco content switching module (6500)On the alteon config, we saw the following:a) /c/slb/adv direct ena aphttp enab) metric minmissesQuestion:1) is there any guide available to migrate from alteon ad3 to ci...

I tried to implement backend SSL over the weekend and was unsuccessful. I've read all the posts here on ssl back to January and I was sure I had a solid config. I saw lots of traffic hitting the ssl module but it would not pass to the backend content...

Hi, I've just booted up a brand new 11501S and I am wondering if I'm having a case of "dead-on-arrival": <snip> 256MB.Volume c: has 1948 Mbytes availableFlash is Up to DateDEC 5 00:40:06 1/1 1 SYSSOFT-4: Flash is Up to DateDEC 5 00:40:09 1/1 2 SYSS...