Heads Up :
The post you are writing will appear in a public forum. Please ensure all content is appropriate for public consumption. Review the employee guidelines for the community here.
Dear sir/Ma,I am aware the the ACE4710 (ACE-4710-04-K9) will be EoL by january 24, 2014..Please what is the replacement product/part number for this?brkuku
Hello everyone!Is it possible to change inline ports wan/lan assignments in inline group on WAVE 694/WAVE 7571 with 4/8 port copper gigabit ethernet inline module through telnet or Central Manager?Can any problems occur if cords were plugged in wrong...
Greetings.Thank you for your valuable time.I would kindly seek your guidance in getting this information regarding cisco 11503 can do either multiple URL redirection or url rewrite.Public users use the url either http://jobs. A.com:80 , http://jobs.B...
Can someone clarify how the ACL wildcard mask works in the ACE30?. Ideally, wildcard mask of 0.0.0.0 should match all but what I am seeing is, it is treating is as match any.Here is the scenario: I would like to capture all traffic between 1.1.1.1 an...
We are upgrading the waas software to a 5x release from 4.4.1.Which 5x version is recommended? We will need to be running in a mix environment until the wae-512s are replaced with 594s. The reason we want to go to a 5x train is to run the ica ao at...
Hi all,I have a new GSS 4492R appliance, running v4.1(1) out of the box, and presently attempting to configure it (creating region, location, etc.) per the GSLB configuration guide. When attemping to issue commands under the "config-gslb" config mo...
I´m working on getting my ACE modules, ACE30, to load balance PPTP traffic but i don´t find how configure it, It is possible that i can do it?. I find that it´s possible with ipsec traffic.
Hi Experts,First of all, our error has persisted for a while on Developing section (Real-Server).Overview of the configuration is .... We has client running web-service request to rserver though ACE4710. There is traditional VIP. After passing VIP be...
Hi board,I am looking for a Cisco WAAS monitoring Plugin for Nagios/Icinga or a simple way to monitor the Appliances/CM via SNMP.I found a plugin on nagiosexchange.org but it seems to be only for 4.X.Somebody here using Nagios/Icinga monitoring for W...
I am new to ACE in our company there is ACE modules installed on 6509 switches as VSS configured and we are running ver A4(2.3) for ACE. Please guide me some good http link to start reading about ACE.-Atul
Hi all !I have in a branche office a WAE-274 connected by console to the auxiliary port of Cisco 1700 router.My question is how can i manage the WAE by telneting to the router ?Thanks for your help.
Just want to get your opinion about shutting down a router that has WAAS on SRE module whether we'd better shut down the WAAS first or we can just simply turn off the router.Please share your opinion on this.
I have an ACE30 with 2 client facing vlans and 2 server facing vlans within the same context. I need to NAT traffic originating from a server to the VIP of client vlan 2, however the default gateway points to client vlan1. How do I configure this?
I have an ACE pair in HA mode running A5.2(2) in one-armed configuration, therefore, doing source NAT. I'm researching a problem with an web serverfarm (L7 "/.*" rule) where one particular URL doesn't work, but it works when going to the back-end ser...
I've got an interesting issue here with an ACE pair. I've set a pretty basic insert-cookie based configuration. However, persistence wasn't working. I fired up HTTP-fox and found that the ACE was setting the cookie to expire in 1970. Here's the rele...
