HelloBeen struggling with a Cisco 1120 today, no warranty left, but would like to get it running again. Tried a new disk and flashed it with tftp from rommon, also tried USB. Unit comes up with FXOS, but not able to install FTD with scope --> firmwar...
Forum Posts
Hello,I have a question about if the FTD license is Out of Compliance status,what is the potential impact on the license regarding the security updates?Does it take the updates or do I have to fix the situation to sync the updates?Thank you.
Hello, If we want to use WCCP on a FTD firewall to redirect web traffic to a Palo Alto Web Proxy, is that possible? I know that Palo Alto doesn't support WCCP but since it would be a Cisco device doing the re-direction, does the receiving device nee...
Resolved! FTD over Remote FMC - 2 FMC Setup
Hi All, I'm in bit of a pickle here as I have a task at hand that has 2 FMC's and 2 FTD's present: Below is the scenario; In an existing setup that constitutes of a FMC(VM) and local FTD's deployed in HA, lets call them FMC-A and FTD-1) are in produ...
hi Cisco experts, can someone teach me how to use FMC API to get all the members of a given network group object? and how to create an network group object and add all the members using API.
Resolved! Talos Connectivity Problem
Hi to all ,i am getting many messages as the following:Severity: criticalModule: Talos CommunicationDescription: 3 modules failed:* URLDB- Failed to retrieve beaker inventory* LSP- Failed to retrieve beaker inventoryMy subscription is active (it expi...
Resolved! TCP-state-bypass on FMC managed FTD
Hi All,I'm seeing tons of %FTD-4-419002: Duplicate TCP SYN from Inside:x.x.x.x/36769 to OUTSIDE:y.y.y.y/80 with different initial sequence number on multiple FTDs where the source IP x.x.x.x is ThousandEyes Enterprise agents' IPs.I've found this doc ...
I have lately realised that there is no way to actually figure out the physical interfaces used by a port-channel in FTD 4110s or 2120s or probably any FTDs through the FMC gui or FTD cli. I asked TAC about this and they also advise there is no way t...
as cisco firepower 2130 throughput is 10 Gbps raw and 5.4 Gbps NGFW and ISP and 760 Mbps when TLS decryption is enabled . Is this 760 Mbps is the overall throughput of the firewall when TLS decryption is enabled or non TLS traffic can pass through 5....
I have 2 x FTD2110 managed by an FMCv, all v6.2.2. I'm trying to create an HA pair using an EtherChannel rather than a single physical link. However, only the physical interfaces are appearing in the dialog box to create the HA pair. The documentatio...
Hello Experts,We have a Cisco Firepower 2130 in production running version 7.4.2.4 which we manage via FMC. A Port-Channel with a VLAN has been configured on the FTD with its own IP address serving as the gateway for DHCP clients while the FTD serves...
Opened a case about this error. Was given this link. Not very helpful to me but others might find it useful.https://www.cisco.com/c/en/us/support/docs/security/firepower-ngfw/217616-troubleshoot-cisco-cloud-configuration.html
I currently have an FTD that has public DNS configured on the management interface (>show network, >show DNS system have Umbrella IPs). I have internal DNS IPs assigned to inside data interface using the platform policy. I did not check enable DNS...
I have setup up a number of FTDS that are managed by FMC in CML labs. I have setup the in-built desktop in CML that is hanging off a FTD. I am able to get the internet via FTD-->Router (NAT)-->External Connector and I am able to get internet access f...
On some pages of the report, the columns are shifted to the right so that the hitcount column moves closer to the page margin. Sometimes, it is too far over, and this column is dropped from the report. Workaround to deliver in html works OK so far.
