cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
224
Views
0
Helpful
1
Replies

About GK Log

CN_donke.xu
Level 1
Level 1

Hello Friends

I want to use GK Connect two CCM,and when i finish all config i  can see this log in my GK,is there something error in this log ?i can't make a internal call now.

GATEWAY TYPE PREFIX TABLE
=========================
Prefix: 701*
Zone VLA10MACGK1 master gateway list:
10.112.127.233:51250 trunk01_7
10.112.127.234:33022 trunk01_1

Prefix: 31#711*
Zone VLA10MACGK1 master gateway list:
10.119.200.12:49753 VLA10GK1POD_2
10.119.200.13:41220 VLA10GK1POD_3

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

.Oct 29 12:47:15 VVO: //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_process: QUEUE_EVENT (minor 0) wakeup
.Oct 29 12:47:15 VVO: //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_rassrv_arq: arqp=0x24718060,crv=0x29, answerCall=0
.Oct 29 12:47:15 VVO: //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_rassrv_sep_arq: ARQ Didn't use GK_AAA_PROC
.Oct 29 12:47:15 VVO: //802E8F572900/802E8F572900/GK/gk_dns_query: No Name servers
.Oct 29 12:47:15 VVO: //802E8F572900/802E8F572900/GK/rassrv_get_addrinfo: (31#7119927) Matched tech-prefix 31#711
.Oct 29 12:47:15 VVO: //802E8F572900/802E8F572900/GK/rassrv_get_addrinfo: (31#7119927) unresolved zone prefix, using source zone VLA10MACGK1
.Oct 29 12:47:15 VVO: //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_rassrv_get_ingress_network: returning default ingress network = 1
.Oct 29 12:47:15 VVO: //802E8F572900/802E8F572900/GK/rassrv_arq_select_viazone: about to check the source side, src_zonep=0x20284848
.Oct 29 12:47:15 VVO: //802E8F572900/802E8F572900/GK/rassrv_arq_select_viazone: matched zone is VLA10MACGK1, and z_invianamelen=0
.Oct 29 12:47:15 VVO: //802E8F572900/802E8F572900/GK/rassrv_arq_select_viazone: about to check the destination side, dst_zonep=0x20284848
.Oct 29 12:47:15 VVO: //802E8F572900/802E8F572900/GK/rassrv_arq_select_viazone: matched zone is VLA10MACGK1, and z_outvianamelen=0
.Oct 29 12:47:15 VVO: //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_rassrv_get_ingress_network: returning default ingress network = 1
.Oct 29 12:47:16 VVO: //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_process: got a TIMER event

.Oct 29 12:47:16 VVO: //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_handle_timers

.Oct 29 12:47:16 VVO: //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_handle_timers: managed timer expired 0xD373EB8

.Oct 29 12:47:25 VVO: //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_process: QUEUE_EVENT (minor 0) wakeup
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Best Regards

Donke xu

1 Accepted Solution

Accepted Solutions

Nadeem Ahmed
Cisco Employee
Cisco Employee

can you please show run from GK along with follow debugs. enable below debugs and make a test call.

Debug gatekeeper main 10

debug gatekeeper call 10

debug ras

debug h225 asn1

debug h245 asn1

also share below command output

show gatekeeper endpoint

show gatekeeper gw

show gatekeeper zone status

show gateway

Br,

Nadeem

Br, Nadeem Please rate all useful post.

View solution in original post

1 Reply 1

Nadeem Ahmed
Cisco Employee
Cisco Employee

can you please show run from GK along with follow debugs. enable below debugs and make a test call.

Debug gatekeeper main 10

debug gatekeeper call 10

debug ras

debug h225 asn1

debug h245 asn1

also share below command output

show gatekeeper endpoint

show gatekeeper gw

show gatekeeper zone status

show gateway

Br,

Nadeem

Br, Nadeem Please rate all useful post.