01-09-2019 02:07 AM - edited 03-18-2019 12:35 PM
Hi guys,
I just jointed a company which uses Cisco IP Phones.
I have a Cisco IP Phone 7942 which not seems to be booting.
When connecting the phone all lights are blinking as on any other Cisco IP Phone,
But on this phone the screen/menu is not loading. It just stays blank.
Looks like the software is not starting.
How can I get this Cisco IP Phone to life?
Any help would be appreciated.
01-09-2019 02:18 AM
01-10-2019 12:11 AM
The port is working well, I've used my own phone connection.
The display displays nothing. Stays blank.
When turning the phone on all lights lit up like on other phones. But after that nothing happens. The screen should turn on and the phone should start connecting and finding an IP address. But the screen is doing nothing.
01-09-2019 03:52 AM
Hello,
Can you describe what is shown on the Screen and what is the status on the CUCM side? Is it possible from "show cdp neighbors" to check if the phone has an IP address?
You may also try to hardware reset the device by unplugging the power and then by pressing continouously the # key, then enter 123456789*0#. This way the device will try to load all the files again from the CUCM
George
01-10-2019 12:17 AM
The screen is showing absolutely nothing. Like it is not on.
I've tried the hardware reset you suggested, but how do I do that?
The phone should still be connected to the networkcable I assume?
01-10-2019 12:37 AM
01-10-2019 01:17 AM - edited 01-10-2019 01:21 AM
When I do that and keep # pressed, the 2 lights next to the screen are blinking amber.
My screen shows nothing.
I start typing 123456789*0# and after that the lights stop flashing.
After I am done typing I disconnect the power wait a few secs and plug it back in.
Phone is doing exactly the same. Starts its boot sequence with all the lights, then the screen stays blank/empty.
01-10-2019 01:57 AM
01-10-2019 02:39 AM
Hi guys, thanks for taking the effort to help me with this issue.
To create a complete view;
- My phone is connected by networkcable. With power over ethernet.
- I plug the phone in, the phone starts (headset, mute, speaker and after that the 2 lights next to the screen goes on and off).
- End of functionality, nothing on the display, no sound in the horn.
- I disconnect the networkcable (and also the powercable because of PoE).
- Press # and reconnect the networkcable.
- I keep pressing # until the lights next to the screen are blinking amber.
- I let go of # and start typing 123456789*0#
- the amber flashing lights next to the screen stop flashing.
- still nothing is shown on the display so I dont know if it is doing anything.
- let it stand there for 15 mins, nothing happens.
- disconnect the networkcable (and the power because of PoE).
- reconnect the networkcable
- phone startsup again with the lightshow, but after that still nothing on the screen.
01-10-2019 03:03 AM
01-11-2019 06:28 AM
I will agree with Harris, you should ask for an RMA
01-10-2019 02:34 AM
Please follow this procedure:
George
01-10-2019 04:09 AM
Hi
My phone 7942 has the same issue , screen blank after I rest it ,
The phone take IP from My dhcp and the TFTP is running
The logs looking like this in TFTP
Connection received from 10.0.1.26 on port 51470 [10/01 14:54:52.585]
Read request for file <term42.default.loads>. Mode octet [10/01 14:54:52.586]
Using local port 52395 [10/01 14:54:52.586]
<term42.default.loads>: sent 2 blks, 672 bytes in 0 s. 0 blk resent [10/01 14:54:52.589]
Connection received from 10.0.1.26 on port 50810 [10/01 14:55:27.488]
Read request for file <term42.default.loads>. Mode octet [10/01 14:55:27.488]
Using local port 64925 [10/01 14:55:27.489]
<term42.default.loads>: sent 2 blks, 672 bytes in 0 s. 0 blk resent [10/01 14:55:27.494]
your advice to solve it
01-11-2019 06:20 AM
04-08-2021 03:06 AM
Hi I've been having the same problem with a Cisco phone once its plugged in the phone only shows a white screen,nothing else comes on as well
Please advise me on how to fix this problem
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide