- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-03-2015 09:17 AM - edited 03-17-2019 02:32 AM
Hello,
I am walking through the guide for the Cube line side setup.
However, Im missing some of the commands from my router (Cisco 2921 with UC license installed).
For instance, I do not have the option of:
voice service voip
extension cucm
or
voice-ctl-file
My global voice config is:
voice service voip
mode border-element license capacity 25
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
sip
Show cube status:
CUBE-Version : 9.0
SW-Version : 15.2.4.M6a, Platform CISCO2921/K9
HA-Type : none
Licensed-Capacity : 25
What am I missing to activate this?
Jason Ryan
Solved! Go to Solution.
- Labels:
-
Other IP Telephony
Accepted Solutions
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-03-2015 10:56 AM
Hi Jason
As per document below :
http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/voice/cube_interop/configuration/15-mt/cube-interop-15-mt-book/voi-cucm-lineside.html
Feature Name | Releases | Feature Information |
---|---|---|
Simplified Line-Side Support of CUCM on CUBE | 15.4(2)T Cisco IOS XE Release 3.12S | The Simplified Line-Side Support of CUCM on CUBE feature simplifies the complex CUBE configurations required for registering IP Phones on a CUCM through CUBE using a single CLI that automatically applies all the necessary configurations. The following commands were modified by this feature: extension cucm and voice-class sip extension cucm. |
Cisco Unified Communications Manager Line-Side Support | 15.3(3)M Cisco IOS XE Release 3.10S | The Cisco Unified Communications Manager Line-Side Support feature provides line-side support for Cisco Unified Communications Manager and IP phones deployed on different logical networks, in both cloud-based and premise-based deployments. The following commands were introduced or modified: access-secure, capf-address, clear voice phone-proxy all-sessions, complete (ctl file), ctl-file (phone proxy), debug voice phone-proxy, description (ctl file), description (phone proxy), disable service-settings, max-concurrent-sessions, phone-proxy (dial peer), port-range, record-entry, show voice class ctl-file, show voice class phone-proxy, service-map, session-timeout, tftp-server address,voice-ctl-file, voice-phone-proxy. |
Seems like you are running below the minimum version requirement for this feature.
Regards
Aditya Gupta
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-03-2015 10:56 AM
Hi Jason
As per document below :
http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/voice/cube_interop/configuration/15-mt/cube-interop-15-mt-book/voi-cucm-lineside.html
Feature Name | Releases | Feature Information |
---|---|---|
Simplified Line-Side Support of CUCM on CUBE | 15.4(2)T Cisco IOS XE Release 3.12S | The Simplified Line-Side Support of CUCM on CUBE feature simplifies the complex CUBE configurations required for registering IP Phones on a CUCM through CUBE using a single CLI that automatically applies all the necessary configurations. The following commands were modified by this feature: extension cucm and voice-class sip extension cucm. |
Cisco Unified Communications Manager Line-Side Support | 15.3(3)M Cisco IOS XE Release 3.10S | The Cisco Unified Communications Manager Line-Side Support feature provides line-side support for Cisco Unified Communications Manager and IP phones deployed on different logical networks, in both cloud-based and premise-based deployments. The following commands were introduced or modified: access-secure, capf-address, clear voice phone-proxy all-sessions, complete (ctl file), ctl-file (phone proxy), debug voice phone-proxy, description (ctl file), description (phone proxy), disable service-settings, max-concurrent-sessions, phone-proxy (dial peer), port-range, record-entry, show voice class ctl-file, show voice class phone-proxy, service-map, session-timeout, tftp-server address,voice-ctl-file, voice-phone-proxy. |
Seems like you are running below the minimum version requirement for this feature.
Regards
Aditya Gupta

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-03-2015 11:04 AM
Hi Aditya,
Very useful information (+5) for me too as I was looking for it.
Thanks
Vivek
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-03-2015 11:18 AM
Hi Aditya,
I did see that at the bottom of the guide, though I read it as saying they simplified the setup in the that OS but not necessarily added it in that one.
Ill upgrade the OS and give it a shot.
Thanks
Jason Ryan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-03-2015 11:35 AM
Aditya,
I updated to 15.4 as mentioned and the commands were there.
Thanks for the help.
Jason Ryan

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-03-2015 11:50 PM
If possible, I'd be interested in seeing your final config if you manage to get it working, along with what handsets you get working.
I haven't seen it working in any attempts made, and there doesn't seem to be much TAC knowledge to provide support on it either.
