05-18-2012 08:38 AM - edited 03-16-2019 11:14 AM
Hey Everyone,
Its been awhile since I posted here. I have a customer runnig CUCME 8.5 on a 2901 ISR with 15.1(3)T IOS. I have a number of users with a 7962 phone with 7915-12 expansion module. The issue is, that these phones are configured with 2 DN's and the remaining 4 buttons on the phone, along with all of the buttons on the 7915 are configured as BLF speed dials. However, on the phones and the expansion modules, they are only showing up as speed dials (it has the keypad icon, as opposed the the keypad w/phone icon which should indicate BLF Speed dial). Here is a sample of one of the ephone configs:
ephone 1
mac-address D4A0.2A89.864E
ephone-template 1
username "dkilway" password dkilway7420
blf-speed-dial 1 7440 label "Mark Keener-7440" device
blf-speed-dial 2 8995 label "Bill King-8995" device
blf-speed-dial 3 8992 label "Matt Dawley-8992" device
blf-speed-dial 4 7430 label "Eric Rooney-7430" device
blf-speed-dial 5 7423 label "Don Thomas-7423" device
blf-speed-dial 6 7432 label "Eric Sweere-7432" device
blf-speed-dial 7 7422 label "Kelly Thornton-7422" device
blf-speed-dial 8 8993 label "Ken Russell-8993" device
blf-speed-dial 9 7421 label "Lynn Baker-7421" device
blf-speed-dial 10 8990 label "Mark Hartsook-8990" device
blf-speed-dial 11 7438 label "Nathan Blood-7438" device
blf-speed-dial 12 7433 label "Peter Wilkinson-7433" device
blf-speed-dial 13 7424 label "Ralph O'Connor-7424" device
blf-speed-dial 14 7439 label "Renata Ashford-7439" device
blf-speed-dial 15 7431 label "Rob Hoffman-7431" device
blf-speed-dial 16 7437 label "Julianne Stadelman - 7437" device
paging-dn 199
type 7962 addon 1 7915-12
button 1:1 2:50
Here is a sample ephone-dn config:
ephone-dn 1 dual-line
no call-waiting beep
number 7420
label Debbie Kilway-7420
description Debbie Kilway-7420
name Debbie Kilway
allow watch
call-forward busy 8000
call-forward noan 8000 timeout 20
corlist incoming Unrestricted-CSS
hold-alert 60 originator
Any ideas as to what could be causing the buttons to show up as speed-dials, as opposed to BLF speed-dials? I also have a TAC case open, but thought I would post here as well. Any assistance is greatly appreciated.
Solved! Go to Solution.
05-18-2012 09:01 AM
Yes as mentioned before:
presence
max-subscriptions XXX
Again, it's all explained in the manual.
05-18-2012 08:43 AM
Have you configured 'presence' and few options under it? Full details in the Administrator Guide.
05-18-2012 08:49 AM
Hi Paolo,
As far as I know, it was working fine without any presence configuration. However, TAC added the following to the config:
sip-ua
presence enable
and i just added this under the ephone
presence call-list
Is there anything else I should maybe add?
05-18-2012 09:01 AM
Yes as mentioned before:
presence
max-subscriptions XXX
Again, it's all explained in the manual.
05-18-2012 09:26 AM
Thanks Paolo,
I believe that may have fixed it. Thanks for your assistance.
05-18-2012 09:29 AM
Thank you for the nice rating and good luck!
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide