Doubts about ephone-ds and dial peer.

[ciscolover]

Hi all,

Ephone-dn --> I think it's used to configure the buttons of the ephones. For example, "button one = extension 1000".

Dial Peer -->I thinks it's used to assign the final extensions to the phones..

This is correct?

With the ephone-dn could I assign a final extension to the phone?? Or it's only used to assign buttons...

I don't understand well the ephone-dn concept.

Thanks all.

[slashdots · Accepted solution]

Ephone-dn -> Create a directory number which can be assined to ephones

Ephone -> Create the phone itself. you have to assign the createte ephone-dn here

Dial-peer-> Used to connect to PSTN/Voicemail/etc. Is a numberpattern which is routet to a specific port

Im not sure what you mean by "button" but if you mean all the function keys of the phones:
Define the keys as a "ephone-template" and assign the template under "Ephone"

Link to the CME Admin Guide with lots of examples: https://www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmeadm.html

hope that helps

[ciscolover]

Thanks for your answer..

When I talk about the buttons I talk about the phone physicall keys. I thought that Ephone-dn are an option assigned to a physicall key of the physicall phone.

If I have understand your answer... Ephone-dn = the number or extension of the phone. After you have create the ephone you assign the Ephone-DN to give it's extension number.

[slashdots]

to answer your second question:

Yes. Thats correct.

[ciscolover]

Thanks for the replyes ¡¡¡

But I have a last doubt:

1º)I create an ephone dn 1000 and ephone dn 2000

2º)I create a ephone 1 and ephone 2

Ok,I can assign the ephone dn 2000 to the ephone 1 button 1. If I press the button 1 I could call the ephone dn 2000

But, how can I assign the telephone number to the ephone 1. Not a button to call another phones, his own phone number??

Thanks '¡¡¡

[ciscolover]

Any?

Please, how can assign a phone number(dn) to an ephone? Not to his buttons to can call another phones?

Regardss'''

[ronpatel · Accepted solution]

Hi

One of the way to assign the phone number to ephone is by using "button" command under ephone configuration.

For example

ephone 1

Button 1:1 , 2:2

This command will assign Dn 1000 to button 1 of your ephone and Dn 2000 to button 2 of your ephone

Regards
Ronak Patel

Rate all helpful post by clicking stars below the answer.

[ciscolover]

Ronak,

But, it assigns DN 1000 to button 1 of my ephone. This meands that if I push the physical button 1 of my physicall phone I log with the extension 1000 ¿?

¿Or when it talks about button is not the physicall button of the phone?  Is another concept?

I hope you understand my question.

Thanks ¡¡¡

[ronpatel]

Hi,

Yes the button 1:1 will give DN number to button 1 of the ip phone. Button command gives DN to  physical button of Ip phone .

Regards
Ronak Patel

Rate all helpful post by clicking stars below the answer.

[ciscolover]

Ok last question. Sorry.

If anyone dials the extension 1000 my physical phone rings?

If I push the physical button 1 I pick up the call ¿?¿?

Thanks

[ronpatel · Accepted solution]

HI

Q 1 If anyone dials the extension 1000 my physical phone rings?

Answer :- Yes  ( provided you do not have any kind of calling restriction using COR lists. )

Q 2 If I push the physical button 1 I pick up the call ¿?¿?

Answer :- Yes

Regards
Ronak Patel

Rate all helpful post by clicking stars below the answer.