cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1610
Views
0
Helpful
5
Replies

FXO using diff codecs

techguy
Enthusiast
Enthusiast

0/0/1         g729r8     n  S_CONNECT             FXOLS_OFFHOOK

0/1/1         g711ulaw   n  S_CONNECT             FXOLS_CONNECT

whats will be the difference between above two since both are connected with different codec.

5 Replies 5

nikshah
Cisco Employee
Cisco Employee

can you add the show run from the gw.

!

trunk group FXO

!

voice-card 0

dspfarm

dsp services dspfarm

!

!

voice rtp send-recv

!

voice service voip

allow-connections h323 to h323

allow-connections h323 to sip

allow-connections sip to h323

allow-connections sip to sip

fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none

h323

sip

  bind control source-interface Loopback10

  bind media source-interface Loopback10

  registrar server

!

voice class codec 1

codec preference 1 g711ulaw

codec preference 2 g711alaw

codec preference 3 g729r8

!

voice class h323 1

  h225 timeout tcp establish 3

!

!

voice iec syslog

!

voice statistics type iec

!

interface Loopback10

ip address 10.5.250.65 255.255.255.192

h323-gateway voip interface

h323-gateway voip bind srcaddr 10.5.250.65

!

!

voice-port 0/0/1

trunk-group FXO

supervisory disconnect anytone

no battery-reversal

input gain -3

output attenuation -1

echo-cancel coverage 64

no comfort-noise

cptone SA

timing hookflash-out 50

connection plar 9801

description *** LOCAL LINE ***

music-threshold -45

bearer-cap Speech

caller-id enable

!

sccp local Loopback10

sccp ccm 10.50.2.4 identifier 2 version 7.0

sccp ccm 10.50.2.3 identifier 1 version 7.0

sccp

!

sccp ccm group 1

associate ccm 2 priority 1

associate ccm 1 priority 2

associate profile 1 register abcd_CONF

associate profile 2 register abcd_XCODE

associate profile 3 register abcd_MTP

!

dspfarm profile 2 transcode

codec g729r8

codec g711alaw

codec g711ulaw

maximum sessions 4

associate application SCCP

!

dspfarm profile 1 conference

codec g729br8

codec g729r8

codec g729abr8

codec g729ar8

codec g711alaw

codec g711ulaw

maximum sessions 1

associate application SCCP

!

dspfarm profile 3 mtp

codec g711ulaw

maximum sessions software 10

associate application SCCP

!

dial-peer voice 10 pots

trunkgroup FXO

tone ringback alert-no-PI

destination-pattern 900.T

fax rate disable

prefix 00

!

dial-peer voice 205 voip

description To CallManager Pub

destination-pattern 9801$

session target ipv4:10.50.2.3

voice-class codec 1

voice-class h323 1

dtmf-relay h245-alphanumeric

req-qos guaranteed-delay audio

acc-qos guaranteed-delay audio

fax-relay ecm disable

fax rate 14400

fax nsf 000000

fax protocol pass-through g711ulaw

no vad

!

telephony-service

srst mode auto-provision all

max-ephones 110

max-dn 400

ip source-address 10.5.51.1 port 2000

max-conferences 8 gain -6

transfer-system full-consult

create cnf-files version-stamp 7960 May 27 2012 17:41:04

Omerpal,

What exactly do you want to know?

Please rate useful posts

"I am complete in God, God completes me"

Please rate all useful posts

I want to know that why some FXO ports are in connected state with G.729r ans some with G.711ualaw. Thanks for your info

Hello All

i have the same problem, any idea how to resolve this issue?

Thanks,

Alexis

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Recognize Your Peers