08-05-2009 11:39 AM - edited 03-15-2019 07:14 PM
But the problem i am facing is that: the conrefence profile is not taking the command " maximum-sessions" & hence the profile shows down all the time...
Plz find the sh run of the router & suggest...
============================================
Building configuration...
Current configuration : 7580 bytes
!
ip cef
!
!
ip domain name
!
voice-card 0
dspfarm
dsp services dspfarm
!
!
application
global
service alternate Default
!
!
!
class-map match-any CALL-SIGNALLING
match ip dscp af31
match ip dscp cs3
class-map match-any VOICE
match ip dscp ef
!
!
policy-map CE-EGRESS-EDGE
class VOICE
priority percent 33
class CALL-SIGNALLING
priority percent 2
class class-default
fair-queue
!
interface FastEthernet0/0
description MPLS IPVPN connection to Etisalat with IP 10.100.100.114
ip address 255.255.255.248
ip ospf network point-to-point
duplex full
speed auto
service-policy output CE-EGRESS-EDGE
ip rsvp bandwidth 168
!
interface FastEthernet0/1
description Life Sales Gateway Address
ip address 10.65.1.11 255.255.255.248
duplex auto
speed auto
!
!
router ospf 1
router-id
log-adjacency-changes
redistribute static subnets
network 10.65.1.11 0.0.0.0 area 0
network 0.0.0.0 area 0
!
ip forward-protocol nd
ip route 10.40.208.0 255.255.255.128 10.65.1.10
ip route 10.40.208.128 255.255.255.128 10.65.1.10
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
!
!
!
!
!
!
control-plane
!
!
!
voice-port 0/1/0
timing hookflash-out 50
!
voice-port 0/1/1
!
voice-port 0/1/2
!
voice-port 0/1/3
!
voice-port 0/2/0
timing hookflash-out 50
!
voice-port 0/2/1
!
voice-port 0/2/2
!
voice-port 0/2/3
!
ccm-manager fallback-mgcp
ccm-manager redundant-host 10.40.64.5
ccm-manager mgcp
no ccm-manager fax protocol cisco
ccm-manager music-on-hold
ccm-manager config server 10.40.64.6
!
mgcp
mgcp call-agent 10.40.64.6 2427 service-type mgcp version 0.1
mgcp dtmf-relay voip codec all mode cisco
mgcp rtp unreachable timeout 1000 action notify
mgcp modem passthrough voip mode nse
mgcp package-capability rtp-package
mgcp package-capability sst-package
mgcp package-capability pre-package
no mgcp package-capability res-package
no mgcp timer receive-rtcp
mgcp sdp simple
mgcp rtp payload-type g726r16 static
mgcp bind control source-interface FastEthernet0/1
mgcp bind media source-interface FastEthernet0/1
!
mgcp profile default
!
sccp local FastEthernet0/1
sccp ccm 10.40.64.6 identifier 1 priority 1 version 6.0
sccp ccm 10.40.64.5 identifier 2 priority 2 version 6.0
sccp
!
sccp ccm group 1
associate ccm 1 priority 1
associate ccm 2 priority 2
associate profile 1 register RSVPdxbLS
switchover method immediate
!
sccp ccm group 100
bind interface FastEthernet0/1
associate ccm 1 priority 1
associate ccm 2 priority 2
associate profile 200 register CFB0024978C10B9
keepalive retries 5
switchover method immediate
switchback method immediate
switchback interval 15
!
dspfarm profile 200 conference
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
associate application SCCP
shutdown
!
dspfarm profile 1 mtp
codec g711ulaw
codec pass-through
rsvp
maximum sessions software 10
associate application SCCP
!
!
dial-peer voice 999010 pots
service mgcpapp
port 0/1/0
!
dial-peer voice 999020 pots
service mgcpapp
port 0/2/0
!
dial-peer voice 9 pots
destination-pattern 9T
incoming called-number .
direct-inward-dial
port 0/2/0
!
!
!
call-manager-fallback
secondary-dialtone 9
max-conferences 8 gain -6
transfer-system full-consult
ip source-address 10.65.1.11 port 2000
max-ephones 42
max-dn 100 dual-line
dialplan-pattern 1 042337... extension-length 3
!
08-05-2009 11:47 AM
Hi, check if you have enough DSP to configure the conference profile.
(show diag or show inventory)
All the best
David
08-05-2009 12:00 PM
Your dspfarm profile is still shut down. Configure the maximum sessions and do a no shut on it.
Please rate if this helped.
08-05-2009 09:31 PM
Hi,
Whenever i try to configure maximum-seesions under the profile it shows "0-0" as the session number & hence the profile is shut down...I have PVDM2-16...
Can u plz suggest..
08-06-2009 12:26 AM
Hi Acharya,
Your MTP profile is consuming all the DSP resources.
I don't know if you need software MTP resources on the gateway.
Try shutting them down and then try the max sessions for the conference profile.
It should work.
Cheers,
Bala.
08-06-2009 12:30 AM
Thanks Bala..I will try it & update
08-06-2009 06:14 AM
The MTP is NOT consuming any DSP resources, it's a SW IOS MTP
maximum sessions software 10
You already have 2 lines configured
dial-peer voice 999010 pots
service mgcpapp
port 0/1/0
!
dial-peer voice 999020 pots
service mgcpapp
port 0/2/0
So if you want CFB options are:
Do NOT use any line on it, meaning disable the above
Add another DSP.
HW CFB requires the WHOLE DSP. You only have 1 and 2 channels are in use.
If you don't know how to calculate DSPs use this
DSP Calculator
http://www.cisco.com/cgi-bin/Support/DSP/cisco_dsp_calc.pl
HTH
java
if this helps, please rate
08-06-2009 09:30 AM
Thanks Java..But can u plz expalin the below (that you mentioned in your post):
=========================================
So if you want CFB options are:
Do NOT use any line on it, meaning disable the above----What to disable?? (dial-peer voice 999010 pots
dial-peer voice 999020 pots)
Add another DSP---how to add another DSP? R u meaning to say add another DSP card into the Router??
08-06-2009 09:37 AM
Simply put, remove all the config for those voice ports and do not use them
Add DSPs = buy pvdm2
HTH
java
if this helps, please rate
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide