06-01-2016 01:04 PM - edited 03-17-2019 07:06 AM
We are setting up 3 new PRIs on a 2951 with Frontier. We received 300 DIDs as part of the setup. The PRIs are registered with CUCM, and they show up on the router. However, when we try to make an incoming call with one of the new DIDs, the calling phone is silent for about 7 seconds, rings destination for like half a second and immediately disappears. We receive the message all circuits are busy on the calling phone. Looking at the debug, this is what I see for the call. Any thoughts?
Jun 1 18:41:44.673: ISDN Se0/1/0:23 Q931: RX <- SETUP pd = 8 callref = 0x1A2D
Bearer Capability i = 0x8090A2
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Facility i = 0x9F8B0100A10F02017706072A8648CE1500040A0100
Protocol Profile = Networking Extensions
0xA10F02017706072A8648CE1500040A0100
Component = Invoke component
Invoke Id = 119
Operation = InformationFollowing (calling_name)
Name information in subsequent FACILITY message
Progress Ind i = 0x8283 - Origination address is non-ISDN
Calling Party Number i = 0x2183, '7659938656'
Plan:ISDN, Type:National
Called Party Number i = 0xA1, '7659839199'
Plan:ISDN, Type:National
Jun 1 18:41:44.677: ISDN Se0/1/0:23 Q931d: srl_send_l3_pak:
source_id = CCM MANAGER 0x0003, dest_id = Q.921 0x0000, prim = DL_DATA_REQ 0x0240
priv_len = 4 int_id = 0x155C633C datasize = 26
Jun 1 18:41:44.677: ISDN Se0/1/0:23 Q931d: data =
Jun 1 18:41:44.677: 155C633C00000003024004BC00010000
Jun 1 18:41:44.677: 08029A2D0D1803A98381
Jun 1 18:41:44.677: ISDN Se0/1/0:23 Q931: TX -> SETUP_ACK pd = 8 callref = 0x9A2D
Channel ID i = 0xA98381
Exclusive, Channel 1
itc-row1rack1-MG01#
Jun 1 18:41:44.677: ISDN Se0/1/0:23 Q931: RX <- FACILITY pd = 8 callref = 0x1A2D
Facility i = 0x9F8B0100A117020178020100800F574952454C4553532043414C4C4552
Protocol Profile = Networking Extensions
0xA117020178020100800F574952454C4553532043414C4C4552
Component = Invoke component
Invoke Id = 120
Operation = CallingName
Name Presentation Allowed Extended
Name = WIRELESS CALLER
Jun 1 18:41:44.713: ISDN Se0/1/0:23 Q931: RX <- STATUS pd = 8 callref = 0x1A2D
Cause i = 0x82E10D - Message type not implemented
Call State i = 0x06
itc-row1rack1-MG01#
Jun 1 18:41:48.673: ISDN Se0/1/0:23 Q931: RX <- SETUP pd = 8 callref = 0x1A2D
Bearer Capability i = 0x8090A2
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Facility i = 0x9F8B0100A10F02017706072A8648CE1500040A0100
Protocol Profile = Networking Extensions
0xA10F02017706072A8648CE1500040A0100
Component = Invoke component
Invoke Id = 119
Operation = InformationFollowing (calling_name)
Name information in subsequent FACILITY message
Progress Ind i = 0x8283 - Origination address is non-ISDN
itc-row1rack1-MG01#
Calling Party Number i = 0x2183, '7659938656'
Plan:ISDN, Type:National
Called Party Number i = 0xA1, '7659839199'
Plan:ISDN, Type:National
itc-row1rack1-MG01#
Jun 1 18:41:50.697: ISDN Se0/1/0:23 Q931d: srl_send_l3_pak:
source_id = CCM MANAGER 0x0003, dest_id = Q.921 0x0000, prim = DL_DATA_REQ 0x0240
priv_len = 4 int_id = 0x155C633C datasize = 21
Jun 1 18:41:50.697: ISDN Se0/1/0:23 Q931d: data =
Jun 1 18:41:50.697: 155C633C00000003024004BC00010000
Jun 1 18:41:50.697: 08029A2D02
Jun 1 18:41:50.701: ISDN Se0/1/0:23 Q931: TX -> CALL_PROC pd = 8 callref = 0x9A2D
Jun 1 18:41:50.701: ISDN Se0/1/0:23 Q931d: srl_send_l3_pak:
source_id = CCM MANAGER 0x0003, dest_id = Q.921 0x0000, prim = DL_DATA_REQ 0x0240
priv_len = 4 int_id = 0x155C633C datasize = 25
Jun 1 18:41:50.701: ISDN Se0/1/0:23 Q931d: data =
Jun 1 18:41:50.701: 155C633C00000003024004BC00010000
Jun 1 18:41:50.701: 08029A2D011E028088
Jun 1 18:41:50.701: ISDN Se0/1/0:23 Q931: TX -> ALERTING pd = 8 callref = 0x9A2D
Progress Ind i = 0x8088 - In-band info or appropriate now available
Jun 1 18:41:50.761: ISDN Se0/1/0:23 Q931: RX <- DISCONNECT pd = 8 callref = 0x1A2D
Cause i = 0x82E018 - Mandatory information element missing
Jun 1 18:41:50.785: ISDN Se0/1/0:23 Q931d: srl_send_l3_pak:
source_id = CCM MANAGER 0x0003, dest_id = Q.921 0x0000, prim = DL_DATA_REQ 0x0240
priv_len = 4 int_id = 0x155C633C datasize = 21
Jun 1 18:41:50.785: ISDN Se0/1/0:23 Q931d: data =
itc-row1rack1-MG01#
Jun 1 18:41:50.785: 155C633C00000003024004BC00010000
Jun 1 18:41:50.785: 08029A2D4D
Jun 1 18:41:50.785: ISDN Se0/1/0:23 Q931: TX -> RELEASE pd = 8 callref = 0x9A2D
Jun 1 18:41:50.861: ISDN Se0/1/0:23 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x1A2D
06-01-2016 01:27 PM
HI Cooper,
I would make sure the the switch type and PCM type(ulaw for T1) is set correctly on GW config on CUCM.You might to involve service provider to make sue D channel is error free at their end.thanks
As per logs soon after transmitting the alerting message you receive a disconnect.
Jun 1 18:41:50.761: ISDN Se0/1/0:23 Q931: RX <- DISCONNECT pd = 8 callref = 0x1A2D
Cause i = 0x82E018 - Mandatory information element missing
06-02-2016 05:34 AM
I will check this. I can say the Telco is saying it isn't their issue. In their words, when we call 765-983-9199 the call rings the endpoint and they see it coming in on channel 1 and immediately jump to channel 2 to see if it is accepted there. Funny thing, one number we have 765-965-5555 comes in on one of the PRIs and works just fine.
Edit - we are using PRI NI2 and PCM Type of u-Law
06-02-2016 09:24 AM
A few things:
- Can you do "sh isdn status" and make sure it says "Multiple frame established"?
- How many digits do you use in your extension? The carrier is sending 10 digits in, you will need to reduce the digits via the gateway page or translation pattern in CUCM.
- Can you post a sh run and gateway page in CUCM?
Thanks,
FG
06-03-2016 11:26 AM
I do see multiple frame established on all three PRIs. we reduce it down to 4 or 5 digits via translation.
here is the config
boot system flash:/c2951-universalk9-mz.SPA.154-3.M3.bin
boot-end-marker
!
!
card type t1 0 0
card type t1 0 1
clock timezone EST -5 0
clock summer-time EDT recurring
network-clock-participate wic 0
network-clock-participate wic 1
network-clock-select 1 T1 0/0/0
network-clock-select 2 T1 0/0/1
network-clock-select 3 T1 0/1/0
!
!
!
!
!
!
isdn switch-type primary-4ess
!
!
trunk group 15B-PRI
description itc-row1rack1-MG01 PRI's
hunt-scheme least-used both
translation-profile incoming SRST-DID-STRIP
!
cts logging verbose
!
voice-card 0
dspfarm
dsp services dspfarm
no local-bypass
!
!
voice call send-alert
voice call carrier capacity active
voice rtp send-recv
!
voice service voip
fax protocol pass-through g711ulaw
modem passthrough nse codec g711ulaw
h323
!
voice class codec 1
codec preference 1 g711alaw
codec preference 2 g711ulaw
codec preference 3 g729br8
codec preference 4 g729r8
!
voice class h323 1
h225 timeout tcp establish 3
!
!
!
!
voice translation-rule 1
rule 1 /9833184/ /8474/
rule 2 /9833186/ /8474/
rule 3 /^.*\(....\)/ /\1/
!
!
voice translation-profile SRST-DID-STRIP
translate called 1
!
!
controller T1 0/0/0
cablelength long 0db
pri-group timeslots 1-24 service mgcp
description Frontier PRI 31/ipzx/612163.FTNC
!
controller T1 0/0/1
cablelength long 0db
pri-group timeslots 1-24 service mgcp
description Frontier PRI 31/ipzx/612161.FTNC
!
controller T1 0/1/0
cablelength long 0db
pri-group timeslots 1-24 service mgcp
description Frontier PRI 31/ipzx/612162.FTNC
!
controller T1 0/1/1
cablelength long 0db
pri-group timeslots 1-24 service mgcp
!
!
class-map match-any Media
match ip dscp ef
class-map match-any Control
match ip dscp af31
match ip dscp cs3
!
policy-map Voice
class Media
set ip dscp ef
class Control
set ip dscp cs3
!
!
interface Serial0/0/0:23
no ip address
encapsulation hdlc
isdn switch-type primary-ni
isdn incoming-voice voice
isdn bind-l3 ccm-manager
no cdp enable
!
interface Serial0/0/1:23
no ip address
encapsulation hdlc
isdn switch-type primary-ni
isdn incoming-voice voice
isdn bind-l3 ccm-manager
no cdp enable
!
interface Serial0/1/0:23
no ip address
encapsulation hdlc
isdn switch-type primary-ni
isdn incoming-voice voice
isdn bind-l3 ccm-manager
no cdp enable
!
interface Serial0/1/1:23
no ip address
encapsulation hdlc
isdn switch-type primary-4ess
isdn incoming-voice voice
isdn bind-l3 ccm-manager
no cdp enable
!
!
mgcp
mgcp call-agent cm02 2427 service-type mgcp version 0.1
mgcp dtmf-relay voip codec all mode out-of-band
mgcp rtp unreachable timeout 1000 action notify
mgcp modem passthrough voip mode nse
mgcp ip qos dscp cs3 signaling
mgcp package-capability rtp-package
mgcp package-capability sst-package
mgcp package-capability pre-package
no mgcp package-capability res-package
no mgcp package-capability fxr-package
no mgcp timer receive-rtcp
mgcp sdp simple
mgcp fax t38 inhibit
mgcp rtp payload-type g726r16 static
mgcp bind control source-interface GigabitEthernet0/0
mgcp bind media source-interface GigabitEthernet0/0
mgcp behavior rsip-range tgcp-only
mgcp behavior comedia-role none
mgcp behavior comedia-check-media-src disable
mgcp behavior comedia-sdp-force disable
!
mgcp profile default
!
sccp local GigabitEthernet0/0
sccp ccm x.x.x.x.identifier 3 version 4.1
sccp ccm x.x.x.x identifier 2 version 4.1
sccp ccm x.x.x.x identifier 1 version 4.1
sccp
!
sccp ccm group 1
associate ccm 1 priority 1
associate ccm 2 priority 2
associate profile 1 register CFB-1501-MDF-MG
registration retries 10
registration timeout 30
switchback method graceful
!
ccm-manager music-on-hold
!
ccm-manager fallback-mgcp
ccm-manager redundant-host cm02 cm01
ccm-manager mgcp
no ccm-manager fax protocol cisco
ccm-manager config server x.x.x.x.
ccm-manager config
!
dspfarm profile 1 conference
codec g711ulaw
maximum sessions 6
associate application SCCP
shutdown
!
dial-peer voice 999 voip
description IP Catch-All
modem passthrough nse codec g711ulaw redundancy
incoming called-number .
voice-class codec 1
voice-class h323 1
fax rate disable
fax protocol pass-through g711ulaw
ip qos dscp cs3 signaling
no vad
!
dial-peer voice 1 pots
trunkgroup 15B-PRI
description SRST -- OUTBOUND POTS (INTERNATIONAL)
destination-pattern 9011T
progress_ind setup enable 3
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
fax rate disable
prefix 011
!
dial-peer voice 2 pots
trunkgroup 15B-PRI
description SRST -- OUTBOUND POTS (411)
destination-pattern 9411
progress_ind setup enable 3
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
fax rate disable
forward-digits 3
!
dial-peer voice 3 pots
trunkgroup 15B-PRI
description SRST -- OUTBOUND POTS DIALING LD
destination-pattern 91[2-9]..[2-9]......
progress_ind setup enable 3
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
fax rate disable
forward-digits 11
!
dial-peer voice 4 pots
trunkgroup 15B-PRI
description SRST -- OUTBOUND POTS DIALING Local
destination-pattern 9[2-9]......
progress_ind setup enable 3
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
fax rate disable
forward-digits 7
!
dial-peer voice 10 pots
trunkgroup 15B-PRI
description SRST -- INBOUND PRI
incoming called-number .
fax rate disable
direct-inward-dial
!
dial-peer voice 911001 pots
trunkgroup 15B-PRI
description SRST -- 911 DIALING POTS
translation-profile outgoing SRST-OUTBOUND-CLID
destination-pattern 9911
forward-digits 3
!
dial-peer voice 1000 voip
description SRST -- INBOUND VOIP
incoming called-number .
voice-class codec 1
voice-class h323 1
ip qos dscp cs3 signaling
!
dial-peer voice 9911001 pots
trunkgroup 15B-PRI
description SRST -- 911 DIALING POTS
destination-pattern 9911
forward-digits 3
!
06-03-2016 11:39 AM
Please can you also attached the MGCP config for 0/1/0 from the CUCM.
You have to make sure the Inbound CSS for gateway has access to the all DN's parition you are trying to reach and also significant digits can be set to 4 if you are using only last 4 digits as extension as service provider is sending full 10 digits.
06-03-2016 11:42 AM
I will try to upload the pics right now.
06-03-2016 11:51 AM
06-03-2016 11:55 AM
Please can you make sure in Inbound calls section on GW config.
1) You have the Inbound CSS for gateway which has access to the all DN's partitions you are trying to reach
2) Significant digits can be set to 4 if you are using only last 4 digits as extension as service provider is sending full 10 digits.
06-03-2016 12:46 PM
i have confirmed that both of those settings are correct. CW- INbound has everything in it, and we are matching at 10 digits with the teleco, which contradicts what i said earlier.
Could it be a dial peer or a route pattern that is causing this issue?
06-03-2016 01:07 PM
It is MGCP so dial-peer doesn't matter . These are only for SRST.
Do you still see the same error ,if yes then you might want to check with provider if you think on CUCM correct translations are applied .
Thanks
06-03-2016 11:56 AM
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide